1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the ADTRAN MX2800 DS3 DC Redundant Multiplexor. This device is designed for rack-mountable deployment and supports SNMP and Telnet for remote management. Please read this manual thoroughly before operating the equipment.
2. Safety Information
Always observe the following safety precautions to prevent injury and damage to the equipment:
- Ensure proper grounding of the equipment.
- Do not operate the device in wet or damp conditions.
- Disconnect power before performing any maintenance or installation procedures.
- Only qualified personnel should perform installation and servicing.
- Ensure adequate ventilation around the unit to prevent overheating.
3. Product Features
The ADTRAN MX2800 Multiplexor offers a robust set of features for reliable network connectivity:
- DS3 DC Redundant operation for enhanced reliability.
- Support for SNMP (Simple Network Management Protocol) for centralized monitoring and management.
- Telnet access for command-line interface configuration and control.
- Designed for standard rack-mounting, optimizing space in data centers and network closets.
- Comprehensive connectivity options including LAN, Modem, DS3/STS-1, and DSX-1/E1 ports.
4. Setup
4.1 Physical Installation
The ADTRAN MX2800 is designed for rack-mounting. Secure the unit in a standard 19-inch equipment rack using appropriate mounting hardware (not included).
4.2 Rear Panel Connections
Refer to the diagram below for an overview of the rear panel connections.
Figure 4.2.1: Rear Panel Layout of the ADTRAN MX2800.
This image displays the rear panel of the ADTRAN MX2800 Multiplexor. From left to right, it features LAN and Modem ports (RJ45), DS3/STS-1 BNC connectors (OUT and IN, labeled A and B), DSX-1/E1 ports (OUT and IN) with multi-pin connectors, DC Power inputs (-48V, 0.7A) with PWR, FAIL, and RET terminals for two redundant power feeds (A and B), a terminal block for T, R, S, CLK connections (A and B), and a 115 AC 50/60Hz 0.8A power inlet.
4.3 Power Connection
Connect the appropriate power source to the unit:
- DC Power: For redundant DC power, connect -48V DC power supplies to the "DC POWER" terminals (A and B). Ensure correct polarity for PWR, FAIL, and RET connections. The unit requires 0.7A per feed.
- AC Power: Connect a standard 115V AC, 50/60Hz, 0.8A power cord to the AC inlet on the far right.
4.4 Network Connections
- LAN/Modem: Connect standard Ethernet cables to the LAN and Modem RJ45 ports for management access. The "NONCRITICAL" and "CRITICAL" alarm contacts are also located near these ports.
- DS3/STS-1: Use BNC cables to connect DS3/STS-1 signals to the "OUT" and "IN" ports (A and B).
- DSX-1/E1: Connect DSX-1/E1 lines to the multi-pin "OUT" and "IN" connectors.
- T, R, S, CLK: Utilize the terminal block for connecting external timing and signaling lines as required for your specific network configuration.
5. Operating Instructions
5.1 Initial Power-Up
Once all connections are secure, apply power to the unit. Observe the front panel indicators (if any, not shown in image) for power and operational status.
5.2 Configuration and Management
The ADTRAN MX2800 can be managed via SNMP or Telnet:
- SNMP: For network management systems, configure the device's IP address and SNMP community strings. Refer to the ADTRAN SNMP MIB documentation for detailed information.
- Telnet: Access the command-line interface (CLI) by connecting to the device's IP address via Telnet. Use the CLI for detailed configuration, status monitoring, and troubleshooting.
Consult the ADTRAN MX2800 Command Reference Guide for a complete list of commands and configuration options.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your ADTRAN MX2800:
- Cleaning: Periodically clean the exterior of the unit with a soft, dry cloth. Do not use liquid or aerosol cleaners.
- Ventilation: Ensure that ventilation openings are clear of dust and obstructions.
- Firmware Updates: Check the ADTRAN support website for available firmware updates to ensure the latest features and security patches.
- Cable Management: Keep all cables neatly organized and secured to prevent accidental disconnections or damage.
7. Troubleshooting
This section provides solutions to common issues. For more complex problems, contact ADTRAN technical support.
| Problem | Possible Cause | Solution |
|---|---|---|
| No Power | Power cable disconnected; Power supply failure. | Check power cable connections. Verify power supply output. |
| Cannot Access via Network (SNMP/Telnet) | Incorrect IP address; Network cable issue; Firewall blocking. | Verify IP configuration. Check LAN cable. Disable temporary firewall for testing. |
| DS3/STS-1 Link Down | Cable fault; Remote equipment issue; Configuration mismatch. | Check BNC cable integrity. Verify remote equipment status. Confirm configuration settings. |
8. Specifications
| Attribute | Detail |
|---|---|
| Manufacturer | ADTRAN, INC. |
| Model Number | LYSB00A8AZKY8-ELECTRNCS |
| ASIN | B00A8AZKY8 |
| Description | MX2800 DS3 DC REDUNDANT W/OUT MODEM |
| Power Input (DC) | -48V DC, 0.7A (Redundant) |
| Power Input (AC) | 115 AC 50/60Hz, 0.8A |
| Management | SNMP, Telnet |
| Mounting | Rack-Mountable |
9. Warranty and Support
For warranty information and technical support, please refer to the official ADTRAN website or contact your authorized ADTRAN reseller. Keep your purchase receipt and product serial number handy when seeking support.
ADTRAN Website: www.adtran.com/support