SBU SBU-600JET26
SBU Jet Ski Cover Instruction Manual
Model: SBU-600JET26
Product Overview
The SBU Jet Ski Cover is a heavy-duty, 600 denier polyester canvas cover designed for personal watercraft. It provides comprehensive protection against environmental elements such as dust, dirt, sun rays, and rain. This cover is suitable for various storage needs, including indoor, outdoor, on-water, and trailering applications.
Key features include:
- Trailerable design with detachable side-release strap buckles.
- Constructed from 600 denier marine-grade 100% solution-dyed woven polyester poly canvas.
- Urethane-coated backing for water resistance and breathability.
- Fabric resists shrinking, stretching, sun rays, dirt, rain, condensation, and tearing.
- Double-stitched 4-ply interlocking seams with rot-proof thread for enhanced durability.
- Rear air vents to reduce wind lofting and internal moisture buildup.
- Integrated fuel gas tank cap access door.
- Underside reinforcements for added protection.
Figure 1: Overview of SBU Jet Ski Cover features, highlighting material, ventilation, and access points.
Installation Guide
Follow these steps to properly install your SBU Jet Ski Cover:
- Prepare the Jet Ski: Ensure the jet ski is clean and dry before covering to prevent moisture trapping and potential damage. Remove any sharp objects or accessories that could tear the cover.
- Unfold the Cover: Lay the cover flat on the ground near the jet ski, identifying the front and rear sections. The lighter grey section typically indicates the front.
- Position the Cover: Drape the cover over the jet ski, starting from the front. Align the front of the cover with the bow of the jet ski.
- Pull Down and Adjust: Pull the cover down evenly over both sides of the jet ski, working your way towards the rear. Ensure the elastic hemline fits snugly around the bottom edge of the watercraft.
- Secure Straps: Locate the detachable side-release strap buckles. Pass the straps under the jet ski and connect them to the corresponding buckles on the opposite side. Tighten the straps to secure the cover firmly, preventing wind lofting during storage or trailering.
- Check Air Vents: Ensure the rear air vents are not obstructed. These vents are crucial for reducing moisture buildup and allowing air circulation.
Figure 2: Properly installed SBU Jet Ski Cover on a personal watercraft.
Figure 3: Detail of the elastic hem for a snug fit around the jet ski.
Figure 4: Rear air vents designed to prevent wind lofting and moisture buildup.
Video 1: Demonstration of the SBU 600D mooring and travel jet ski cover, highlighting its features and fit.
Usage and Applications
The SBU Jet Ski Cover is designed for versatile use across various scenarios:
- Storage: Ideal for long-term storage, whether indoors in a garage or outdoors. It protects against dust, dirt, UV rays, and precipitation.
- Mooring: Can be used while the jet ski is moored on the water, at a dock, or on a floating jet dock. The detachable straps allow for secure mooring without needing to remove the entire cover.
- Trailering: The cover is trailerable, meaning it can remain on the jet ski while being transported on a trailer. The secure strap system and rear air vents are designed to withstand highway speeds and prevent ballooning or flapping.
Figure 5: Jet ski covered for outdoor storage, showcasing protection from elements.
Figure 6: Cover in use during trailering, emphasizing secure fit for transport.
Maintenance and Care
Proper maintenance will extend the life of your SBU Jet Ski Cover:
- Cleaning: Clean the cover periodically with mild soap and water. Use a soft brush or sponge to remove dirt and grime. Rinse thoroughly with clean water and allow it to air dry completely before folding and storing. Do not use harsh chemicals or abrasive cleaners.
- Drying: Always ensure the cover is completely dry before folding and storing it in the included storage bag. Storing a damp cover can lead to mildew and fabric degradation.
- Inspection: Regularly inspect the cover for any signs of wear, tear, or damage to the seams and straps. Address minor issues promptly to prevent them from worsening.
- Winter Storage: The cover can serve as an alternative to shrink wrap for winterizing your personal watercraft. Its material is designed to withstand temperature extremes without cracking or disintegrating.
Figure 7: Double-stitched seams for enhanced durability and longevity.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Cover appears loose or flaps during trailering. | Straps not sufficiently tightened; incorrect cover size. | Ensure all side-release straps are securely fastened and tightened. Verify the cover is the correct model for your jet ski. The rear air vents are designed to minimize wind lofting. |
| Moisture or mildew under the cover. | Jet ski was covered while damp; insufficient air circulation. | Always ensure the jet ski is completely dry before covering. The cover's breathable material and air vents help, but proper drying is essential. Clean any mildew with a mild solution and air dry. |
| Difficulty accessing fuel tank. | Unaware of access feature. | Utilize the integrated zippered fuel tank access door for convenient refueling without removing the entire cover. |
Specifications
- Model Number: SBU-600JET26
- Material: 600 denier Marine Grade 100% Solution Dyed Woven Polyester Poly Canvas with Urethane Coating
- Color: Black & Gray
- Water Resistance Level: Water Resistant
- Item Package Dimensions: 109 x 12 x 12 inches
- Item Dimensions (LxWxH): 8 x 4 x 12 inches (Note: These are likely folded dimensions, not installed dimensions)
- Package Weight: 5 Pounds
Warranty and Support
SBU provides a 2-year protection against manufacturing defects or workmanship issues for this product. For any questions, support, or warranty claims, please contact SBU customer support. Our team is dedicated to assisting you with your product needs.
You can find more information and contact details by visiting the official SBU store on Amazon: SBU Store.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.