Bryant Electric RL320
Bryant Electric RL320 Fluorescent Lampholder User Manual
Model: RL320 | Brand: Bryant Electric
1. Product Overview
The Bryant Electric RL320 is a medium bi-pin fluorescent lampholder designed for T8 and T12 lamps. It features a disconnect function, a 4-wire configuration, and a pedestal-type, tall profile. This lampholder supports both slide-on and snap-in installation methods and includes a captive nut for secure mounting. It is rated for 660 watts and 600 volts, and comes in a white finish.
Figure 1: Bryant Electric RL320 Fluorescent Lampholder. This image shows the white lampholder with its tall profile, bi-pin lamp receptacles, and the integrated screw with captive nut for mounting.
Key Features:
- T8-T12 disconnect functionality
- Tall profile design
- Compatible with bi-pin lamps
- Supports both slide-on and snap-in installation
2. Important Safety Information
WARNING: Risk of electric shock. Installation must be performed by a qualified electrician in accordance with all local and national electrical codes.
- Always disconnect power at the circuit breaker or fuse box before installing, servicing, or removing the lampholder.
- Ensure the lampholder's voltage and wattage ratings (600 volts, 660 watts) are compatible with your lighting fixture and electrical system.
- Do not exceed the maximum rated wattage or voltage.
- Inspect the lampholder for any damage before installation. Do not install if damaged.
- Keep children away from electrical components.
3. Setup and Installation
This section provides general guidelines for installing the Bryant Electric RL320 Fluorescent Lampholder. Always refer to the specific instructions provided with your lighting fixture and consult local electrical codes.
Installation Steps:
- Power Disconnection: Before beginning any work, turn off the power to the lighting circuit at the main electrical panel (circuit breaker or fuse box). Verify that power is off using a voltage tester.
- Mounting: The RL320 supports slide-on and snap-in mounting. Align the lampholder with the mounting slots on your fluorescent fixture. Slide it into place or snap it securely until it locks. Use the integrated screw with the captive nut to further secure the lampholder if required by your fixture design.
- Wiring: Connect the four wires from the lampholder to the corresponding wires in your fixture's ballast or wiring harness. Ensure all connections are secure and properly insulated. The lampholder is designed for 4-wire connections.
- Lamp Insertion: Once the lampholder is securely mounted and wired, insert the T8 or T12 bi-pin fluorescent lamp by aligning the pins with the lampholder slots and rotating the lamp until it clicks into place.
- Power Restoration: After ensuring all connections are correct and secure, restore power at the main electrical panel.
4. Operating Instructions
The Bryant Electric RL320 Fluorescent Lampholder is designed for straightforward operation once installed.
Inserting a Fluorescent Lamp:
- Ensure the power to the fixture is OFF.
- Align the two pins at one end of the fluorescent lamp with the slots in the lampholder.
- Push the lamp firmly into the lampholder until the pins are fully seated.
- Rotate the lamp approximately 90 degrees until it locks into place. You should feel a slight click or resistance indicating it is secure.
- Repeat for the other end of the lamp if using two lampholders.
Removing a Fluorescent Lamp:
- Ensure the power to the fixture is OFF.
- Rotate the lamp approximately 90 degrees in the opposite direction of insertion until the pins are aligned with the slots.
- Gently pull the lamp straight out from the lampholder.
5. Maintenance
The Bryant Electric RL320 Fluorescent Lampholder requires minimal maintenance. Regular inspection and cleaning can help ensure its longevity and safe operation.
- Cleaning: With power disconnected, gently wipe the lampholder with a dry, soft cloth to remove dust or debris. Do not use liquid cleaners or abrasive materials.
- Inspection: Periodically inspect the lampholder for any signs of wear, cracking, discoloration, or loose connections. If any damage is observed, disconnect power and replace the lampholder immediately.
- Lamp Replacement: Always replace fluorescent lamps with the correct type (T8 or T12 bi-pin) and ensure they are fully seated in the lampholder.
6. Troubleshooting
If you encounter issues with your fluorescent lighting fixture, the problem may not always be with the lampholder itself. Here are some common issues and potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light up. | No power to fixture. | Check circuit breaker/fuse. Ensure wall switch is ON. |
| Lamp does not light up. | Faulty fluorescent lamp. | Replace lamp with a new, known-good lamp. |
| Lamp does not light up. | Loose or incorrect wiring. | (Power OFF!) Check all wiring connections to the lampholder and ballast. Ensure they are secure. Consult a qualified electrician if unsure. |
| Lamp does not light up. | Faulty ballast. | If other lamps in the fixture work, or if the new lamp doesn't work, the ballast may be faulty. Ballast replacement should be done by a qualified electrician. |
| Lamp flickers or hums. | Old or failing lamp. | Replace the fluorescent lamp. |
| Lamp flickers or hums. | Loose connection at lampholder. | (Power OFF!) Ensure lamp pins are fully seated and rotated into the lampholder. Check wiring connections. |
If troubleshooting steps do not resolve the issue, it is recommended to consult a qualified electrician.
7. Specifications
Detailed technical specifications for the Bryant Electric RL320 Fluorescent Lampholder:
| Attribute | Value |
|---|---|
| Brand | Bryant Electric |
| Model Number | RL320 |
| Type | Medium Bi-Pin Fluorescent Lampholder |
| Lamp Compatibility | T8 and T12 Fluorescent Lamps |
| Voltage Rating | 600 Volts |
| Wattage Rating | 660 Watts |
| Wiring | 4-wire |
| Mounting Type | Pedestal type, Slide-on and Snap-in with captive nut |
| Profile | Tall |
| Color | White |
| Material | Copper (internal contacts) |
| Item Weight | 0.95 ounces |
| Product Dimensions | 3 x 1.5 x 0.7 inches |
| UPC | 883778112355 |
8. Warranty Information
Bryant Electric products are manufactured to high standards. For specific warranty terms and conditions applicable to the RL320 Fluorescent Lampholder, please refer to the official warranty statement provided by Bryant Electric at the time of purchase or visit their official website. Keep your proof of purchase for warranty claims.
9. Support
For technical assistance, product inquiries, or further support regarding your Bryant Electric RL320 Fluorescent Lampholder, please contact Bryant Electric customer service or visit their official website. Contact information can typically be found on the product packaging or the manufacturer's website.
Bryant Electric Official Website: www.hubbell.com/bryantelectric/en/