WENKO 4460030100

WENKO Strip-it 4460030100 Oval Hooks Instruction Manual

Model: 4460030100 | Brand: WENKO

1. Introduction

Thank you for choosing the WENKO Strip-it 4460030100 Oval Hooks. This instruction manual provides essential information for the proper setup, operation, and maintenance of your new wall hooks. Please read this manual thoroughly before installation and retain it for future reference.

WENKO Strip-it Oval Hook, front view

Figure 1: Front view of a single WENKO Strip-it Oval Hook. The hook is white, oval-shaped, and made of plastic, designed for wall mounting.

2. Package Contents

The WENKO Strip-it 4460030100 package includes the following items:

  • 3 x WENKO Strip-it Oval Hooks (White, Plastic)

3. Specifications

BrandWENKO
Model Number4460030100
MaterialPlastic
ColorWhite
Finish TypeWhite
Mounting TypeWall Mount (Adhesive)
Dimensions (L x W x H)0.79 x 0.98 x 1.57 inches (2.0 x 2.5 x 4.0 cm)
Item Weight0.564 ounces (16 Grams)
Number of Hooks3
Maximum Weight Recommendation35 Pounds (Note: Adhesion strength can vary based on surface and application.)
UPC764558456862
WENKO Strip-it Oval Hook dimensions diagram

Figure 2: Diagram illustrating the dimensions of the WENKO Strip-it Oval Hook: Height (H) 4 cm (1.57 inch), Width (B) 2.5 cm (0.98 inch), Depth (T/D) 2 cm (0.79 inch).

4. Setup and Installation

The WENKO Strip-it hooks are designed for easy adhesive mounting. Follow these steps for proper installation:

  1. Prepare the Surface: Ensure the mounting surface is clean, dry, and smooth. Wipe the area with a clean cloth and a mild cleaner if necessary, then dry thoroughly. Avoid porous, uneven, or freshly painted surfaces.
  2. Position the Hook: Determine the desired location for the hook.
  3. Apply Adhesive: The hooks utilize a "Strip-it" adhesive system. Carefully peel the protective backing from the adhesive pad located on the back of the hook. Note: Some adhesive pads may require trimming to fit the hook's shape precisely. If so, carefully cut the adhesive to match the oval contour of the hook before peeling the backing.
  4. Attach the Hook: Press the hook firmly against the prepared surface for at least 30 seconds. Apply even pressure across the entire adhesive area.
  5. Allow Adhesion Time: For optimal adhesion, allow the hook to set for at least 24 hours before hanging any items. This allows the adhesive to fully bond with the surface.
WENKO Strip-it Oval Hook, side view showing adhesive pad

Figure 3: Side view of the WENKO Strip-it Oval Hook, illustrating the adhesive pad on the back for wall mounting.

5. Operating Instructions

Once installed and fully adhered, the WENKO Strip-it Oval Hooks are ready for use.

  • Hang towels, tea towels, small bags, or other lightweight items on the hook.
  • Ensure the total weight of items hung does not exceed the maximum weight recommendation of 35 pounds (approximately 15.8 kg). Exceeding this limit may cause the hook to detach.
  • The hooks are suitable for use in various household areas, including bathrooms, kitchens, and general living spaces.

6. Maintenance

To maintain the appearance and functionality of your WENKO Strip-it Oval Hooks:

  • Clean the hooks regularly with a soft, damp cloth.
  • Avoid using abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the plastic finish.
  • If the hook needs to be relocated, carefully peel it off the surface. The "Strip-it" design allows for removal without leaving residue, provided the surface is suitable.

7. Troubleshooting

If you encounter issues with your WENKO Strip-it Oval Hooks, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Hook does not adhere properly or falls off.
  • Surface was not clean or dry.
  • Surface is porous, uneven, or textured.
  • Insufficient pressure applied during installation.
  • Adhesive not allowed sufficient time to bond (less than 24 hours).
  • Weight limit exceeded.
  • Adhesive pad not properly trimmed or applied.
  • Ensure surface is thoroughly cleaned and dried before application.
  • Apply only to smooth, non-porous surfaces like tiles, glass, or smooth painted walls.
  • Press firmly for at least 30 seconds during installation.
  • Wait a full 24 hours before hanging items.
  • Reduce the weight of items hung on the hook.
  • Ensure the adhesive pad is correctly sized and fully covers the contact area on the hook.
Adhesive pad is difficult to apply or does not fit the hook.Adhesive pad may require manual trimming.Carefully trim the adhesive pad to match the oval shape of the hook before peeling the backing and applying.

8. Warranty and Support

For information regarding warranty coverage, product support, or to contact customer service, please visit the official WENKO website or refer to your purchase documentation.

WENKO Official Website

© 2023 WENKO. All rights reserved.

This manual is for informational purposes only.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.