BRINKS Indoor Digital Timer with Photocell

1. Product Overview

The BRINKS Indoor Digital Timer with Photocell (Model 44-2010) is designed to automate the on/off cycles of indoor lighting and appliances. It features a photocell sensor for automatic dusk-to-dawn operation and allows for timed operation in 2-hour increments. This timer is suitable for various indoor applications, enhancing convenience and security.

Figure 1: Front view of the BRINKS Indoor Digital Timer, displaying the light sensor, time increment buttons, ON/OFF control, and light sensitivity dial.

2. Safety Information

• Indoor Use Only: This timer is designed exclusively for indoor applications. Do not use it outdoors or in wet environments.
• Electrical Rating: Connect this timer only to a 120V, 60Hz power source. Ensure the connected load does not exceed 8 Amperes, 1250 Watts (Tungsten), or 1/3 Horsepower.
• Proper Grounding: Always plug the timer into a properly grounded 3-prong outlet.
• Avoid Overloading: Do not plug in appliances that exceed the timer's maximum electrical rating. Overloading can cause overheating and fire hazards.
• Keep Away from Children: Store and operate the timer out of reach of children.
• Do Not Disassemble: Do not attempt to open or repair the timer. Refer all servicing to qualified personnel.

3. Setup and Installation

1. Unpack the Timer: Carefully remove the timer from its packaging.
2. Select a Location: Choose an indoor electrical outlet that is easily accessible and where the timer's photocell sensor will receive adequate ambient light for dusk-to-dawn operation, if desired. Avoid locations where the sensor might be blocked or exposed to direct artificial light sources that could interfere with its function.
3. Plug in the Timer: Insert the timer directly into a standard 120V, 60Hz wall outlet.
4. Connect Appliance: Plug the appliance or lamp you wish to control into the timer's outlet. Ensure the appliance is switched to the 'ON' position if it has its own power switch.

4. Operating Instructions

4.1 Manual ON/OFF Operation

• To manually turn the connected appliance ON or OFF, press the ON/OFF button located on the front of the timer.
• The indicator light will illuminate when the timer is in the ON state.

4.2 Setting Timed Operation (2-Hour Increments)

• The timer allows you to set operation for 2, 4, 6, 8, or 12 hours.
• Press the desired time increment button (2, 4, 6, 8, or 12 HOURS). The corresponding indicator light will illuminate.
• Once the set time has elapsed, the timer will automatically turn off the connected appliance.

4.3 Photocell (Dusk-to-Dawn) Operation

The built-in photocell sensor detects ambient light levels to automatically turn the connected appliance ON at dusk and OFF at dawn. This feature is ideal for controlling lights.

• To activate photocell mode, ensure no time increment button is selected. The timer will then operate based on the light sensor.
• Adjusting Light Sensitivity: The timer features a dial labeled 'L' (Light) to adjust the photocell's sensitivity.
• Turning the dial towards the 'less' side (counter-clockwise) will cause the timer to activate when it is darker outside.
• Turning the dial towards the 'more' side (clockwise) will cause the timer to activate when it is lighter outside.
• Adjust the dial gradually and observe the timer's behavior over a 24-hour cycle to find the optimal setting for your environment.

5. Maintenance

• Cleaning: Disconnect the timer from the power outlet before cleaning. Wipe the exterior with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
• Photocell Sensor: Ensure the photocell sensor is kept clean and free from obstructions (dust, dirt, furniture) to maintain accurate light detection.
• Storage: When not in use, store the timer in a cool, dry place away from direct sunlight and extreme temperatures.

6. Troubleshooting

• Timer does not turn ON/OFF:
  • Ensure the timer is securely plugged into a working 120V, 60Hz outlet.
  • Verify that the connected appliance is functioning correctly and its power switch is in the 'ON' position.
  • Check if the appliance's power consumption exceeds the timer's maximum rating (8A, 1250W, 1/3HP).
• Photocell not activating at desired light level:
  • Adjust the 'L' (Light) sensitivity dial. Turn clockwise for activation in brighter conditions, counter-clockwise for darker conditions.
  • Ensure the photocell sensor is not obstructed by dust, dirt, or nearby objects.
  • Relocate the timer if it is exposed to inconsistent light or direct artificial light sources (e.g., streetlights, indoor lamps) that might interfere with its operation.
• Timer indicator light is off:
  • Confirm the timer is receiving power from the wall outlet.
  • If using timed operation, ensure a time increment button is selected and its indicator light is on.
  • If using photocell mode, the light will only be on when the timer is actively supplying power to the appliance.

7. Specifications

Figure 2: Back view of the BRINKS Indoor Digital Timer, detailing electrical ratings and model information.

8. Warranty and Support

8.1 Limited Warranty

This BRINKS product is covered by a limited warranty. For specific details regarding the warranty period and terms, please refer to the packaging or contact customer support. The warranty typically covers defects in materials and workmanship under normal use.

8.2 Customer Support

For technical assistance, troubleshooting, or warranty inquiries, please contact Hampton Products customer support. Contact information can typically be found on the product packaging or the manufacturer's official website.

Please have your product model number (44-2010) and purchase information ready when contacting support.