Introduction
This manual provides comprehensive instructions for the Fossil Men's Nate Chronograph Watch, Model JR1401. This timepiece features a robust stainless steel construction, a 50mm case, chronograph functionality, and water resistance up to 50 meters (5 ATM). Please read this manual carefully to ensure proper use and maintenance of your watch.
Figure 1: Front view of the Fossil Men's Nate Chronograph Watch.
Setup and Time Adjustment
To ensure accurate timekeeping and functionality, follow these steps to set up your watch:
- Setting the Time:
- Pull the crown (center knob on the side of the watch) out to position 2.
- Turn the crown clockwise or counter-clockwise to set the hour and minute hands to the desired time.
- Push the crown back into position 1 to start the watch.
- Setting the Date:
- Pull the crown out to position 1 (first click).
- Turn the crown clockwise to adjust the date.
- Once the correct date is displayed, push the crown back into its original position.
- Using the Chronograph (Stopwatch):
- Press the top pusher (A) to start the chronograph.
- Press the top pusher (A) again to stop the chronograph.
- Press the bottom pusher (B) to reset the chronograph hands to zero.
Figure 2: Side view illustrating the crown and chronograph pushers.
Operating the Watch
The Fossil Nate Chronograph Watch is designed for daily wear and features a robust construction. The unidirectional rotating bezel can be used for timing events, such as elapsed time up to 60 minutes. Align the triangle marker on the bezel with the minute hand at the start of an event, then read the elapsed time on the bezel as the minute hand progresses.
Figure 3: The Fossil Nate watch comfortably worn on a wrist.
Maintenance and Care
Proper care will extend the life and appearance of your Fossil watch:
- Water Resistance: This watch is water resistant up to 50 meters (5 ATM). It is suitable for short periods of recreational swimming and showering. It is not suitable for diving or snorkeling. Ensure the crown is fully pushed in before any water exposure.
- Cleaning: Use a soft, damp cloth to wipe the watch case and strap. For the stainless steel bracelet, a soft brush can be used to clean between links. Avoid harsh chemicals or abrasive materials.
- Battery Replacement: The watch uses 1 Lithium Metal battery (included). Battery replacement should be performed by a qualified watch technician to maintain water resistance and proper function.
- Band Adjustment: The stainless steel bracelet features a secure fold-over clasp closure. Links can be removed for a customized fit. This watch is interchangeable with all 24mm Fossil straps.
Figure 4: Back view of the watch, highlighting the stainless steel bracelet and clasp.
Troubleshooting
If you encounter any issues with your watch, please refer to the following common solutions:
- Watch Not Running: Check if the crown is fully pushed in. If the watch still does not run, the battery may need replacement.
- Incorrect Time/Date: Follow the "Setting the Time" and "Setting the Date" instructions in the Setup section.
- Chronograph Hands Not Resetting to Zero: This may require a specific reset procedure or professional adjustment. Consult Fossil customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | JR1401 |
| Case Size | 50mm |
| Band Width | 24mm |
| Movement | Quartz Chronograph |
| Lens Material | Hardened Mineral Crystal |
| Water Resistance | 50m (165ft) / 5 ATM |
| Material | Stainless Steel |
| Battery | 1 Lithium Metal (included) |
| Product Dimensions | 5.91 x 5.91 x 5.91 inches; 10.4 ounces |
Figure 5: Men's watch case size guide for reference.
Warranty and Support
For warranty information regarding your Fossil Men's Nate Chronograph Watch, please refer to the official Fossil website or the warranty document included with your purchase. For further assistance or technical support, please visit the Official Fossil Store or contact Fossil customer service.
