1. Product Overview
E6000 QuickHOLD is a versatile, all-purpose craft contact adhesive and sealant. It features a thin consistency designed for precise applications and a quick-dry formula that facilitates faster project completion. This adhesive becomes water resistant immediately upon application, is paintable, and dries clear.
Image 1.1: Front packaging of E6000 QuickHOLD 380722 adhesive.
Key Features:
- Withstands extreme weather conditions.
- Suitable for household use.
- Designed not to crack or crumble.
- High-strength craft adhesive ideal for bonding wood, fabric, leather, ceramic, glass, and metal.
- Thin formula for quick drying.
- Nozzle tip designed for precise applications.
- Dries clear, waterproof, and paintable.
2. Safety Information and Warnings
WARNING: FLAMMABLE. VAPOR HARMFUL. IRRITANT. MAY PRODUCE ALLERGIC REACTION BY SKIN CONTACT. Contains Toluene, Ethyl Acetate, Acetone, and Methyl Ethyl Ketone. Prolonged exposure may cause irritation of eyes, nose, throat, or respiratory tract. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful. Keep out of reach of children. Keep away from heat, sparks, and open flame. Do not use near heat, sparks, or open flame. Use only in a well-ventilated area. Avoid breathing vapors. Wash hands immediately after use. Store container tightly closed.
FIRST AID: If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, wash with plenty of soap and water. If symptoms persist, get medical attention. If inhaled, move to fresh air. If symptoms persist, get medical attention. For further health information, contact a poison control center. This product contains a chemical known to the State of California to cause cancer. For more information, visit www.P65Warnings.ca.gov.
Image 2.1: Back packaging of E6000 QuickHOLD 380722, detailing safety warnings and usage instructions.
3. Setup and Preparation
- Ensure the work area is well-ventilated.
- Gather all materials to be bonded.
- Clean surfaces thoroughly to remove dust, dirt, grease, or oil. Surfaces should be dry before application.
- Pre-fit items to ensure proper alignment before applying adhesive.
- Protect your work surface with newspaper or a drop cloth.
- Twist the cap to break the seal and remove it.
4. Operating Instructions (Application)
E6000 QuickHOLD is a contact adhesive, meaning it forms a strong bond when applied to both surfaces and allowed to partially dry before joining.
- Application: Apply a thin, even coat of QuickHOLD to each surface to be bonded.
- Drying Time: Allow the adhesive to dry for approximately 2 to 3 minutes. The adhesive will become tacky during this time.
- Bonding: Press the two surfaces firmly together. The adhesive will form a strong, permanent bond upon contact.
- Adjustments: Minor adjustments can be made before the adhesive fully sets.
- Full Cure: The adhesive will reach full cure in 24 to 72 hours, depending on temperature and humidity.
Image 4.1: Demonstrating the application of E6000 QuickHOLD adhesive to attach decorative beads to a container.
Tips for Best Results:
- For precise application, utilize the fine nozzle tip.
- Work in a temperature range of 40°F to 150°F (4°C to 66°C).
- Immediately replace the cap after use to prevent the adhesive from drying out in the tube.
- If the adhesive continues to ooze after squeezing, briefly replace the cap to stop the flow, then remove it again for continued use.
Image 4.2: An example of a finished craft project, a decorative mirror, showcasing the potential applications of E6000 QuickHOLD adhesive.
5. Maintenance and Storage
- Always replace the cap tightly after each use to prevent the adhesive from drying and clogging the nozzle.
- Store the adhesive in a cool, dry place, away from direct sunlight and heat sources.
- Ensure the product is stored out of reach of children and pets.
- If the nozzle becomes clogged, use a pin or thin wire to clear it.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Adhesive does not bond effectively. | Surfaces were not clean or dry; insufficient drying time before joining; incorrect application amount. | Ensure surfaces are clean and dry. Apply a thin, even coat to both surfaces. Allow 2-3 minutes for adhesive to become tacky before pressing surfaces together. |
| Adhesive continues to flow from the tube after squeezing. | Pressure build-up in the tube. | Briefly replace the cap on the tube to stop the flow, then remove it to continue application. Always replace the cap tightly when not in use. |
| Nozzle is clogged. | Adhesive dried inside the nozzle. | Use a thin wire or pin to clear the obstruction from the nozzle. Always cap tightly after use. |
| Adhesive is not drying clear. | Excessive application; improper curing conditions. | Apply a thin, even layer. Ensure adequate ventilation and appropriate temperature for curing. |
7. Specifications
| Attribute | Detail |
|---|---|
| Brand | E6000 |
| Model Number | 380722 |
| Product Dimensions | 1.4 x 3.6 x 7.1 inches; 2 ounces (59.1 mL) |
| Item Form | Gel |
| Color | Clear |
| Material Compatibility | Wood, Fabric, Leather, Ceramic, Glass, Metal |
| Water Resistance | Immediate upon application |
| Paintable | Yes |
| Manufacturer | Eclectic Products, Inc. |
| Date First Available | May 7, 2012 |
8. Warranty and Support
Limited Warranty:
The manufacturer will not accept liability beyond product replacement. This warranty is limited to the replacement of the product only.
Technical Support:
For technical assistance, please contact Eclectic Products, Inc. at 1-800-767-4667.
Additional information can be found at quickholdcraft.com.