Livex Lighting 5081-01 Flush Mount with Seeded Glass Shades

Introduction

This instruction manual provides detailed guidance for the safe installation, operation, and maintenance of your Livex Lighting 5081-01 Flush Mount fixture. Please read all instructions carefully before beginning installation and retain this manual for future reference.

Image: Livex Lighting 5081-01 Flush Mount fixture in Antique Brass with seeded glass shades. This image shows the complete assembled fixture.

Safety Information

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

• Always disconnect power at the main fuse or circuit breaker before installation, servicing, or cleaning.
• Consult a qualified electrician if you are unsure about the installation process.
• Ensure all electrical connections are made in accordance with local codes and ordinances.
• Do not exceed the specified wattage for bulbs.
• Handle glass components with care to prevent breakage.
• Keep children away from the work area during installation.

Package Contents

Before installation, carefully unpack your new fixture and lay out all parts on a clear area. Ensure all components are present and undamaged. Refer to Fig. 1 in the installation section for component identification.

• Mounting screw
• Single bar
• Junction Box (existing, not included)
• Green Screw (GND)
• Screw Box
• Canopy (A)
• Pipe nipple (C)
• Lamp holder (F)
• Glass bell (H)
• Big ring (G)
• Pipe (D)
• Bulb (E) - 3 x 60W Candelabra Base (Bulbs included as per specifications, but verify upon receipt)

Installation Instructions

Follow these steps carefully for proper installation of your ceiling mount fixture.

Image: Detailed installation diagram (Fig. 1) and wiring diagram (Fig. 2) for the Livex Lighting 5081-01 Flush Mount fixture.

1. Shut off Power: Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.
2. Unpack and Inspect: Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.
3. Prepare Mounting Screws: Thread the two mounting screws about 1/4" into the pre-drilled holes in the single bar spaced the same distance apart as the holes in the fixture canopy (A).
4. Attach Single Bar: Install the single bar to the Junction Box with the two Junction Box Screws as shown. The side of the single bar marked "GND" must face out.
5. Wiring Connections: While holding the column assembly towards the ceiling, connect the electrical wires as shown in Fig. 2. Make sure that all wire nuts are secured. You may have to wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect the fixture ground wire to it. Otherwise, connect fixture's ground wire directly to the Mounting strap with the green screw provided. After wires are connected, tuck them carefully inside the Junction Box.
6. Attach Pipe Nipple: Attach the pipe nipple (C) to top coupling of the lamp holder (F) and lock it until tight. Attach the canopy (A) onto the pipe nipple (C) and lock it until tight.
7. Place Candle Sleeve: Place the candle sleeve (E) onto the lamp holder (F).
8. Install Bulbs: Install the light bulbs in accordance with the fixture specifications. NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE! (3 x 60W Candelabra Base).
9. Attach Glass Bell: Attach the glass bell (H) insert to the big ring (G). While holding the big ring (G) and canopy (A), hook it by the hook at both of the pipe (D).
10. Secure Canopy: Attach the canopy (A) to the junction box, aligning screws on single bar with mounting holes in canopy and lock it securely with ball nut (B).

Your installation is now complete. Return power to the junction box and test the fixture.

Operating Instructions

This fixture is designed for simple operation once installed.

• Power On/Off: Operate the light fixture using the standard wall switch connected to the circuit.
• Bulb Type: Uses 3 x 60W Candelabra Base (E26 Medium) incandescent bulbs. Ensure replacement bulbs match these specifications.
• Control Method: The product specifications mention "Control Method: App" and "Switch Type: Touch". For standard operation, use a wall switch. These features may refer to compatibility with smart home systems or specific smart switches, which are not included with the fixture.

Maintenance

Regular maintenance ensures the longevity and appearance of your fixture.

• Cleaning: To clean the fixture, first ensure power is off. Wipe with a soft, dry cloth. Do not use abrasive cleaners or solvents as they may damage the finish or glass.
• Bulb Replacement:
  1. Turn off power at the circuit breaker.
  2. Allow bulbs to cool completely before touching.
  3. Carefully unscrew the old bulb from the socket.
  4. Screw in a new 60W Candelabra Base (E26 Medium) incandescent bulb. Do not overtighten.
  5. Restore power and test the light.

Troubleshooting

If your fixture is not operating correctly, refer to the following common issues and solutions:

If you are unable to resolve the issue, please contact customer support or a qualified electrician.

Product Specifications

Warranty and Support

Warranty Information:

All Livex Lighting products purchased come with a 30-day replacement parts policy to ensure a fully working item. Additionally, all products are covered under a 1-year warranty when purchased on Amazon. The warranty period begins on the day the product is originally shipped. The warranty covers all items and conditions identified in the original manufacturer's warranty. Items specifically not covered by the warranty include loss and theft, water damage, customer abuse, and finish deterioration due to UV or coastal exposure.

Customer Support:

For further assistance, replacement parts, or warranty claims, please contact Livex Lighting customer support. You can also visit the official Livex Store for more information and products: Livex Lighting Store.