1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Jensen HDS3000 Weatherproof Heavy Duty Dual Cone Surface-Mount Speakers. Please read this manual thoroughly before attempting to install or operate the speakers to ensure proper function and longevity. Retain this manual for future reference.
2. Safety Information
- Ensure all wiring connections are secure and properly insulated to prevent short circuits.
- Do not expose speakers to extreme temperatures or direct flame.
- Always disconnect power from the audio system before making any electrical connections.
- Avoid prolonged listening at high volume levels to prevent hearing damage.
- When drilling mounting holes, verify there are no electrical wires, fuel lines, or other critical components behind the surface.
3. Package Contents
Verify that your package contains the following items:
- Two (2) Jensen HDS3000 Surface-Mount Speakers
- Mounting Hardware (screws, brackets if applicable)
- This Instruction Manual
4. Setup and Installation
4.1 Mounting the Speakers
The Jensen HDS3000 speakers are designed for surface mounting. Choose a flat, stable location that can support the weight of the speakers and allows for proper sound dispersion. Ensure the mounting surface is free from obstructions.
- Position the speaker in the desired mounting location.
- Mark the locations for the mounting screws using the speaker's base as a template.
- Drill pilot holes at the marked locations. Ensure the drill bit size is appropriate for the mounting screws to prevent stripping or cracking the surface.
- Secure the speaker to the mounting surface using the provided hardware. Do not overtighten the screws.
Figure 1: Jensen HDS3000 Weatherproof Surface-Mount Speakers. These speakers are designed for robust outdoor and marine environments.
4.2 Wiring Connections
Connect the speakers to your audio system's amplifier or head unit. Observe proper polarity to ensure optimal sound performance.
- Identify the positive (+) and negative (-) terminals on both the speaker and your audio source.
- Connect the positive (+) wire from the speaker to the positive (+) output of your amplifier/head unit.
- Connect the negative (-) wire from the speaker to the negative (-) output of your amplifier/head unit.
- Ensure all connections are tight and free from corrosion. Use marine-grade connectors if installing in a wet environment.
5. Operation
Once properly installed and wired, your Jensen HDS3000 speakers will function as part of your audio system. Turn on your audio source (e.g., stereo, receiver) and adjust the volume to your desired listening level. These speakers are designed for a nominal impedance of 4 Ohms and a maximum power handling of 60 watts.
6. Maintenance
To ensure the longevity and performance of your weatherproof speakers, follow these maintenance guidelines:
- Cleaning: Periodically wipe the speaker grilles and enclosures with a soft, damp cloth. Avoid using harsh chemicals or abrasive cleaners, which can damage the finish or weatherproof seals.
- Inspection: Regularly check all mounting hardware and wiring connections for tightness and signs of corrosion or wear. Tighten any loose screws and replace damaged wiring as needed.
- Environmental Exposure: While designed to be weatherproof, prolonged exposure to direct sunlight, extreme temperatures, or harsh marine conditions can affect the lifespan. Consider covering the speakers when not in use for extended periods in such environments.
7. Troubleshooting
If you experience issues with your speakers, consult the following table before contacting support:
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from speakers |
|
|
| Distorted or poor sound quality |
|
|
| Only one speaker working |
|
|
8. Specifications
The following are the technical specifications for the Jensen HDS3000 speakers:
| Model Name | HDS3000 |
| Speaker Type | Dual Cone, Surface Mount |
| Max Power Handling | 60 Watts |
| RMS Power | 30 Watts |
| Nominal Impedance | 4 Ohms |
| Sensitivity @ 1W/1 Meter | 89 dB |
| Frequency Response | 90-15,000 Hz |
| Material | Polypropylene (Woofer Cone) |
| Color | Black |
| Overall Dimensions (each) | 11.3D x 17W x 12.1H Centimetres (6.69" x 4.76" x 4.43") |
| Item Weight (pair) | 2.2 Kilograms (4.8 Lbs) |
| Special Features | Durable, Weatherproof |
9. Warranty and Support
Jensen products are manufactured to high quality standards. For information regarding warranty coverage, please refer to the warranty card included with your purchase or visit the official Jensen website. For technical support or service inquiries, please contact Jensen customer service through their official channels.
Note: Product specifications and design are subject to change without notice.
