ArtToFrames 16x32 inch Satin Black Picture Frame Instruction Manual

1. Product Overview

This manual provides instructions for the assembly, installation, and care of your ArtToFrames 16x32 inch Satin Black Picture Frame. This frame is designed to hold a 16x32 inch photo, poster, diploma, or artwork. The frame is made of MDF, measuring 1.25 inches wide and 0.75 inches deep, with a 0.375 inch deep rabbet (the space below the lip to the bottom of the frame). It comes with Plexi Glass for protection.

Figure 1: ArtToFrames 16x32 inch Satin Black Picture Frame. This image displays the full view of the frame with a landscape picture inserted, highlighting its sleek black finish.

Figure 2: Dimensions of the 16x32 inch Satin Black Picture Frame. The image shows the frame with measurements indicating its 16-inch width and 32-inch length, confirming the size for which it is designed.

Figure 3: Cross-section view of the frame profile. This image illustrates the construction of the frame, showing the MDF material and the rabbet depth where the artwork and backing are secured.

2. Setup and Installation

Your ArtToFrames picture frame comes with all necessary hardware for wall mounting. Follow these steps to prepare your frame and hang it securely.

2.1 Unpacking and Preparation

• Carefully remove the frame from its packaging. Inspect for any damage.
• Remove the protective film from both sides of the Plexi Glass.
• Gather the included hanging hardware: wire, D-rings, screws, and a nail hook. You will also need a screwdriver, pencil, and tape measure.

Figure 4: Included hanging hardware. This image shows the wire, two D-rings, two screws, and a nail hook, which are provided for wall mounting the frame.

2.2 Attaching Hanging Hardware to the Frame

For secure hanging, attach the D-rings and wire to the back of the frame.

1. On the back of the frame, measure approximately one-third of the way down from the top edge on both vertical sides. Mark these points with a pencil.
2. Position a D-ring at each marked point. Use a screwdriver to secure each D-ring with the provided screws. Ensure the D-rings are firmly attached.
3. Thread the hanging wire through the openings of both D-rings. Twist the wire around itself several times at each D-ring to create a secure loop. Ensure the wire is taut but has a slight slack when pulled upwards, forming a gentle curve.

2.3 Inserting Your Artwork

To insert your picture or artwork:

1. Carefully bend back the metal tabs on the back of the frame.
2. Remove the backing board and the Plexi Glass.
3. Place your artwork inside the frame, followed by the Plexi Glass (with protective film removed) and then the backing board.
4. Bend the metal tabs back down to secure the contents firmly in place.

Figure 5: Frame with mat for visualization. This image shows how a mat can be used within the frame to enhance the presentation of smaller artwork, though the mat is not included with this specific frame.

2.4 Wall Mounting the Frame

Once the hardware is attached and your artwork is in place, you can hang the frame on your wall.

1. Hold the frame against the wall in the desired position. Use a level to ensure it is straight.
2. Mark the center point at the top of the frame on the wall with a pencil.
3. Measure approximately 3 inches directly below this mark. This is where your picture frame hanger will be installed.
4. Carefully hammer the nail hook into the wall at the 3-inch mark. Ensure it is secure.
5. Hang the frame by placing the wire onto the installed nail hook. Adjust as needed to ensure the frame is level and secure.

Figure 6: Frame displayed on a wall. This image shows the 16x32 inch frame hanging on a wall above a small table, demonstrating its aesthetic integration into a home decor setting.

3. Maintenance and Care

Proper care will ensure the longevity and appearance of your ArtToFrames picture frame.

• Cleaning the Frame: Wipe the frame gently with a soft, dry cloth to remove dust. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
• Cleaning the Plexi Glass: For cleaning the Plexi Glass, use a soft, lint-free cloth. Do not use paper towels, as they can scratch the surface. A mild, non-abrasive cleaner specifically designed for acrylic or plastic can be used if necessary. Gently wipe the surface to avoid scratches.
• Handling: Always handle the frame by its edges to avoid touching the Plexi Glass surface or the artwork directly.
• Placement: Avoid placing the frame in direct sunlight or in areas with extreme temperature fluctuations or high humidity, as this can affect the frame material and artwork.

4. Troubleshooting

If you encounter any issues with your frame, consider the following common solutions:

• Artwork Not Fitting: Ensure your artwork is precisely 16x32 inches. If it is slightly larger, it may need trimming. Check for any internal spacers or debris that might prevent the artwork from seating correctly.
• Plexi Glass Appears Scratched or Damaged: Ensure all protective films have been completely removed from both sides of the Plexi Glass. If the Plexi Glass is genuinely scratched or damaged upon arrival, refer to the warranty information for replacement options.
• Frame Not Hanging Level: Re-check the placement of the D-rings on the back of the frame to ensure they are at equal distances from the top edge. Adjust the nail hook on the wall if necessary, using a level to verify alignment.
• Loose Components: If the backing or Plexi Glass feels loose, ensure all metal tabs are bent firmly against the backing board.

5. Specifications

6. Warranty and Support

6.1 Warranty Information

ArtToFrames offers a 30-day money-back guarantee. For any damages incurred during shipping, all original packaging must be saved to facilitate claims. Please retain your proof of purchase.

6.2 Customer Support

For further assistance, questions, or support regarding your ArtToFrames product, please visit the official ArtToFrames store or contact their customer service. You can find more information and contact details on their Amazon store page:

Visit the ArtToFrames Store on Amazon