Craftsman 139.53753 Garage Door Remote Control Instruction Manual

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your Craftsman 139.53753 Garage Door Remote Control. This remote is designed for use with specific garage door openers.

1.1 Compatibility

The Craftsman 139.53753 remote control is compatible with Craftsman, Liftmaster, Do-It, Master-Mechanic, Raynor, and Chamberlain garage door openers that utilize Security+ ERT technology, manufactured in 2005 or later. Key indicators for compatibility include:

• Your garage door opener has a PURPLE program/learn button on the back or side of the powerhead.
• Your garage door opener has a PURPLE antenna wire.
• Your original remote control has BLACK buttons.
• Your original remote control or opener indicates "315 MHz" frequency.

Important: This remote is not compatible with systems using other types of coding or different learn button colors (e.g., red, orange, green, yellow).

2. Safety Information

Please read and understand all safety warnings before operating your garage door opener and remote control. Improper use can result in serious injury or property damage.

• Keep remote controls out of reach of children.
• Operate the garage door only when it is in full view, free of obstructions, and the opener is properly adjusted.
• Do not allow children to play with the garage door opener or remote control.
• Test the safety reversal system of your garage door opener monthly.
• Dispose of batteries properly according to local regulations.

3. Package Contents

Your package should contain the following items:

• Craftsman 139.53753 Garage Door Remote Control
• Visor Clip
• CR2 Lithium Battery (pre-installed or separate)

Image of the Craftsman 139.53753 garage door remote control. It is grey with a large black button at the top and two smaller black buttons below it. A metal clip is attached to the side for visor mounting. The brand 'CRAFTSMAN' and '315' are printed on the bottom front.

4. Setup and Programming

Follow these steps to program your Craftsman 139.53753 remote control to your compatible garage door opener. Ensure you have access to your garage door opener's motor unit.

1. Locate the Learn Button: On your garage door opener's motor unit, locate the PURPLE learn button. This button is typically found on the back or side panel of the motor unit.
2. Activate Learn Mode: Press and immediately release the PURPLE learn button. The learn indicator light on the opener will illuminate steadily for 30 seconds, indicating it is in programming mode.
3. Program the Remote: Within 30 seconds of activating the learn mode, press and hold the desired button on your new Craftsman remote control.
4. Confirm Programming: Continue holding the remote button until the garage door opener's light flashes or you hear two clicks. This indicates that the remote has been successfully programmed.
5. Release Button: Release the button on the remote control.
6. Test Operation: Press the programmed button on your remote control to test its operation. The garage door should activate.

If you are programming multiple garage doors, repeat these steps for each door, using a different button on the remote for each opener.

5. Operating the Remote Control

Your Craftsman 139.53753 remote control is designed for simple operation.

• Opening/Closing the Garage Door: Press the programmed button on the remote control once to activate your garage door opener. The door will begin to open or close. Pressing the button again during operation will stop the door. Pressing it a third time will reverse its direction.
• Multiple Doors: If you have programmed multiple garage doors to different buttons on your remote, simply press the corresponding button for the desired door.
• Security+ 3-Function: This remote transmits a new security code each time a button is pressed, enhancing security.

6. Maintenance

6.1 Battery Replacement

The remote control uses one CR2 Lithium battery. When the remote's range decreases or the indicator light on the remote dims, it is time to replace the battery.

1. Open the Remote Casing: Carefully open the remote control casing. This usually involves prying it open with a small flat-head screwdriver at a designated notch.
2. Remove Old Battery: Remove the old CR2 Lithium battery.
3. Insert New Battery: Insert a new CR2 Lithium battery, ensuring the positive (+) terminal is facing the correct direction as indicated inside the battery compartment.
4. Close Casing: Snap the remote control casing back together securely.
5. Test Remote: Test the remote control to ensure it is functioning correctly.

Note: Dispose of old batteries responsibly according to local regulations.

7. Troubleshooting

If your remote control is not functioning as expected, refer to the following common issues and solutions:

8. Specifications

• Model Number: 139.53753
• Brand: CRAFTSMAN
• Frequency: 315 MHz
• Compatibility: Garage door openers with PURPLE learn button (Security+ ERT technology, 2005+)
• Number of Buttons: 3 (for up to three garage doors)
• Security Features: Security+ 3-Function (transmits a new security code every time)
• Battery Type: 1 x CR2 Lithium (not included, but often pre-installed)
• Item Weight: Approximately 2.4 ounces
• Dimensions: Approximately 5.5 x 2.8 x 1 inches (Package Dimensions)
• Color: Black, Grey

9. Warranty and Support

For warranty information or technical support regarding your Craftsman 139.53753 Garage Door Remote Control, please refer to the documentation provided with your purchase or contact Craftsman customer service directly. Contact details can typically be found on the official Craftsman website or on your product packaging.

For additional resources, you may visit the CRAFTSMAN Store on Amazon.