Important Safety Instructions
WARNING: This is an electric heating pad. Never leave the pad unattended while in use. Keep the pad away from flammable materials. Do not use the pad if the cord is damaged. Always unplug the pad when not in use. Keep the pad dry. Do not use the pad if it has been damaged or if you suspect a malfunction. Always follow the instructions provided with the pad. Keep the pad out of the reach of children and pets. If the pad becomes hot to the touch, unplug it immediately and do not use it again until it has cooled down. If you experience discomfort or pain while using the pad, stop using it immediately and consult a doctor. If the pad malfunctions or causes injury, stop using it immediately and contact the manufacturer.
Product Overview
The Sunbeam BW1214-030-470 Heated Electric Microplush Blanket provides warmth and comfort. It features an exclusive warming system designed to deliver consistent heat.
- Microplush fabric for softness.
- Pre-heat feature to warm cold sheets.
- Easy-to-use ComfortSet controller with digital display and push-button controls.
- Exclusive warming system for consistent warmth.
- 100% polyester, channeled microplush construction.
- 10 heat settings.
- 10-hour auto-off function.
Image: The Sunbeam Heated Microplush Blanket in Walnut, King size, folded to display its soft texture and the two attached ComfortSet controllers.
Setup Instructions
- Unpack the Blanket: Carefully remove the blanket and controllers from the packaging.
- Position the Blanket: Place the heated blanket on your bed with the label at the foot of the bed. Ensure the blanket is spread evenly and not bunched up.
- Connect the Controller(s): Locate the connector(s) on the blanket. Firmly plug the controller cord(s) into the blanket connector(s) until it clicks securely. For King size blankets, there are typically two controllers, one for each side of the bed.
- Connect to Power: Plug the power cord(s) from the controller(s) into a 120V AC electrical outlet. Ensure the outlet is not controlled by a wall switch if you intend for the blanket to remain on.
- Route Cords: Arrange the cords so they are not pinched or tangled and do not pose a tripping hazard.
Image: A close-up view of the Sunbeam ComfortSet controller, showing the digital display, 'On/Off', '+', '-', and 'Preheat' buttons, and the 10-hour auto-off indicator.
Operating Instructions
Using the ComfortSet Controller
- Turn On: Press the 'On/Off' button to turn the blanket on. The digital display will illuminate, showing the current heat setting.
- Adjust Heat Setting: Use the '+' and '-' buttons to select your desired heat level, from 1 (low) to 10 (high).
- Pre-heat Function: To pre-warm your bed, press the 'Preheat' button. The blanket will heat up quickly and then return to your last selected heat setting after a period.
- Auto-Off Timer: The blanket is equipped with a 10-hour auto-off feature for safety and energy conservation. It will automatically turn off after 10 hours of continuous use.
- Turn Off: Press the 'On/Off' button again to turn the blanket off. Always unplug the blanket when not in use.
Image: A detailed close-up of the soft, microplush fabric texture of the Sunbeam heated blanket, highlighting its channeled design.
Care and Maintenance
Washing Instructions
- Disconnect Power: Always ensure the blanket is unplugged from the wall outlet and the controller(s) are disconnected from the blanket before washing.
- Pre-soak (Optional): For best results, pre-soak the blanket for 15 minutes in mild soap and cold water.
- Machine Wash: Wash on the 'delicate' or 'gentle' cycle in a washing machine with cold water and a small amount of mild, non-detergent soap. Do not use bleach.
- Rinse: Rinse on the 'normal' cycle with cold water.
- Machine Dry: Tumble dry on a low heat setting for 5-10 minutes. Remove while still damp and air dry over a clothesline or shower rod. Do not use commercial dryers or iron the blanket.
- Storage: Ensure the blanket is completely dry before storing. Store in a cool, dry place.
Important: Do not dry clean, iron, or use mothballs on the heated blanket. These actions can damage the heating elements and void the warranty.
Troubleshooting Guide
| Problem | Possible Cause | Solution |
|---|---|---|
| Blanket does not heat. | Power cord not securely plugged in. Controller not connected to blanket. Outlet not active. | Ensure all connections are firm. Check if the outlet is working by plugging in another appliance. |
| Controller display is off or flashing. | Loose connection. Internal error. | Unplug the blanket from the wall, disconnect the controller from the blanket, wait 5 minutes, then reconnect everything securely. If the issue persists, contact customer support. |
| Blanket heats unevenly. | Blanket is bunched or folded. | Ensure the blanket is spread flat on the bed without any folds or bunches. |
| Blanket feels too hot or not warm enough. | Heat setting is too high or too low. | Adjust the heat setting using the '+' or '-' buttons on the controller. |
Product Specifications
| Feature | Detail |
|---|---|
| Model Number | BW1214-030-470 |
| Brand | Sunbeam |
| Material | Polyester (Microplush) |
| Color | Walnut |
| Size | King (90"L x 108"W) |
| Heat Settings | 10 |
| Auto-Off Timer | 10-hour |
| Special Features | Exclusive Warming System, Pre-heat Feature, Channeled Microplush |
| Item Weight | 8.45 pounds |
| UPC | 027045737227 |
Warranty and Support
Warranty Information
This Sunbeam Heated Electric Microplush Blanket comes with a 5-year limited warranty. Please refer to the warranty card included with your product for specific terms and conditions, including coverage details and how to make a claim.
Customer Support
For technical assistance, troubleshooting not covered in this manual, or warranty claims, please contact Sunbeam Customer Service. Contact information can typically be found on the product packaging, the official Sunbeam website, or the warranty card.
