Jesco Lighting TM616WH 6-Inch Aperture Line Voltage Trim Recessed Light User Manual

1. Introduction

Thank you for choosing the Jesco Lighting TM616WH 6-Inch Aperture Line Voltage Trim Recessed Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before installation and retain them for future reference.

2. Safety Information

WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing. All electrical connections must be made in accordance with local codes, ordinances, or the National Electric Code (NEC). If you are unfamiliar with proper electrical wiring connections, consult a qualified electrician.

• Ensure the power supply is turned off before installation, maintenance, or bulb replacement.
• Do not install this fixture in wet locations unless specifically rated for such use. This trim is suitable for shower applications when used with an appropriate IC or Non-IC housing.
• Handle glass components with care to prevent breakage.
• Use only bulbs that comply with the specified wattage and type.
• Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

3. Product Overview and Components

The Jesco Lighting TM616WH is a 6-inch aperture line voltage trim designed for recessed lighting applications. It features a flat frosted opal glass diffuser and a white finish, suitable for various indoor environments, including showers.

• Diameter: 8-1/4 inches
• Aperture: 5-1/8 inches
• Finish: White
• Lamp Type: A19 120V (bulb not included)
• Maximum Wattage: 40W (for IC Housing) or 60W (for Non-IC Housing)
• Material: Glass (shade)

4. Setup and Installation

Installation of this recessed light trim requires an existing compatible recessed housing (not included). It is strongly recommended that installation be performed by a qualified electrician to ensure safety and compliance with all electrical codes.

1. Prepare the Area: Ensure the power to the circuit where the light will be installed is turned OFF at the circuit breaker or fuse box.
2. Verify Housing Compatibility: Confirm that your recessed housing is compatible with a 6-inch aperture trim. The TM616WH trim has an 8-1/4 inch outer diameter and a 5-1/8 inch aperture.
3. Install the Lamp: Before installing the trim into the housing, insert an A19 120V lamp (bulb) into the socket of the recessed housing. Ensure the wattage does not exceed 40W for IC (Insulation Contact) rated housings or 60W for Non-IC rated housings.
4. Secure the Trim: Carefully align the trim with the recessed housing. Most trims use torsion springs or friction clips to secure themselves within the housing. Gently push the trim upwards until it sits flush with the ceiling surface.
5. Restore Power: Once the trim is securely in place, restore power to the circuit at the breaker or fuse box.
6. Test Operation: Turn on the light switch to verify proper operation.

5. Operating Instructions

The Jesco Lighting TM616WH recessed light trim operates by simply turning on the wall switch connected to its circuit. Ensure a compatible A19 120V bulb is installed within the recessed housing.

• Power On/Off: Use the standard wall switch to control the light fixture.
• Dimming: If connected to a dimmable bulb and a compatible dimmer switch, the light output can be adjusted. Refer to your dimmer switch and bulb instructions for compatibility.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your light fixture. Always disconnect power before performing any maintenance.

• Cleaning: To clean the trim and glass diffuser, wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or glass.
• Bulb Replacement:
  1. Turn off power to the fixture at the circuit breaker.
  2. Carefully pull down the trim from the recessed housing to access the bulb.
  3. Unscrew the old A19 bulb and replace it with a new one of the same type and wattage (max 40W for IC, 60W for Non-IC).
  4. Gently push the trim back into the housing until it is flush with the ceiling.
  5. Restore power and test the light.

7. Troubleshooting

If your light fixture is not functioning correctly, refer to the following troubleshooting guide:

If you are unable to resolve the issue after following these steps, please contact Jesco Lighting customer support or a qualified electrician.

8. Specifications

9. Warranty and Support

Warranty: This Jesco Lighting product is covered by an 18-month manufacturer warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.

Customer Support: For technical assistance, warranty claims, or any questions regarding your Jesco Lighting TM616WH fixture, please contact Jesco Lighting customer service. Refer to the official Jesco Lighting website for current contact information.

Please note: Unauthorized repairs or modifications to the product will void the warranty.