Jesco Lighting TM309WH

Jesco Lighting TM309WH Recessed Light Trim Instruction Manual

Model: TM309WH

Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Jesco Lighting TM309WH 3-Inch Aperture Low Voltage Trim Recessed Light. Please read this manual thoroughly before installation and retain it for future reference.

Safety Information

WARNING: Risk of electric shock. Disconnect power at the fuse box or circuit breaker before installation or servicing. All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC).

  • Ensure the power supply is OFF before beginning installation.
  • Consult a qualified electrician if you are unsure about the installation process.
  • Do not install in locations where the operating temperature exceeds the fixture's rating.
  • Use only MR16 12V 35/50W lamps as specified.
  • Maximum wattage: 35W for IC (Insulation Contact) Housing or 50W for Non-IC Housing. Verify your housing type before installing a lamp.

Package Contents

Verify that all components are present before beginning installation:

  • Jesco Lighting TM309WH Recessed Light Trim (White Finish, Flat Frosted Opal Glass)
  • (Note: Recessed housing and MR16 lamp are sold separately and are required for complete installation.)

Setup and Installation

This trim is designed for use with compatible 3-inch recessed housings (sold separately). Ensure the housing is properly installed and wired according to its own instructions and local electrical codes.

Dimensions and Compatibility

Diagram showing the dimensions of the Jesco Lighting TM309WH recessed light trim, with an overall diameter of 3-5/8 inches and an aperture of 3 inches.

Figure 1: Dimensional diagram of the TM309WH trim. The trim has an overall diameter of 3-5/8 inches and a 3-inch aperture, designed to fit standard 3-inch recessed housings.

  • Overall Diameter: 3-5/8 inches
  • Aperture: 3 inches
  • Lamp Type: MR16 12V 35/50W (not included)
  • Maximum Wattage: 35W (IC Housing) / 50W (Non-IC Housing)

Installation Steps

  1. Turn Off Power: Ensure power to the recessed housing circuit is OFF at the breaker.
  2. Install Lamp: Carefully insert the MR16 lamp (not included) into the lamp holder within the recessed housing. Ensure the lamp wattage does not exceed the housing's rating (35W for IC, 50W for Non-IC).
  3. Insert Trim: Align the trim with the recessed housing. Gently push the trim into the housing until the retention clips (if applicable to your housing) engage and hold the trim securely in place.
  4. Secure Trim: Ensure the trim is flush with the ceiling surface.
  5. Restore Power: Turn the power back ON at the circuit breaker.

Operating Instructions

Once installed and powered, the Jesco Lighting TM309WH recessed light trim operates in conjunction with your existing wall switch or dimmer (if installed). Simply use the wall switch to turn the light ON or OFF.

A modern kitchen and dining area illuminated by multiple recessed lights, showcasing the aesthetic integration of the Jesco Lighting TM309WH trim.

Figure 2: Example of recessed lighting in a modern interior setting, demonstrating typical application.

Maintenance

Regular maintenance ensures optimal performance and longevity of your light fixture.

  • Cleaning: Disconnect power before cleaning. Wipe the trim and glass with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners or solvents.
  • Lamp Replacement: Disconnect power before replacing the lamp. Allow the lamp to cool completely. Carefully remove the old MR16 lamp and insert a new one of the correct type and wattage (MR16 12V, max 35W for IC / 50W for Non-IC).
  • Inspection: Periodically inspect the trim for any signs of damage or loose connections.

Troubleshooting

ProblemPossible CauseSolution
Light does not turn ON.
  • No power to the circuit.
  • Faulty lamp.
  • Loose wiring connection.
  • Check circuit breaker or fuse.
  • Replace lamp with a new one.
  • Ensure all connections are secure (consult electrician if unsure).
Light flickers.
  • Loose lamp.
  • Incorrect dimmer switch (if applicable).
  • Voltage fluctuations.
  • Ensure lamp is seated firmly.
  • Use a dimmer compatible with low voltage MR16 lamps.
  • Consult an electrician.
Lamp burns out quickly.
  • Over-wattage lamp.
  • Poor ventilation in housing.
  • Ensure lamp wattage does not exceed 35W (IC) or 50W (Non-IC).
  • Verify housing is not excessively insulated if it's a Non-IC type.

If problems persist, contact a qualified electrician or Jesco Lighting customer support.

Specifications

ModelTM309WH
BrandJesco Lighting
Aperture Size3 inches
Overall Diameter3-5/8 inches
Lamp Type (Recommended)MR16 12V 35/50W (not included)
Max Wattage (IC Housing)35W
Max Wattage (Non-IC Housing)50W
FinishWhite
Glass TypeFlat Frosted Opal Glass
MaterialGlass
StyleVoltage Trim Recessed / Modern
Light Fixture FormRecessed

Warranty and Support

For warranty information and customer support, please refer to the documentation provided with your original purchase or visit the official Jesco Lighting website. Keep your purchase receipt for warranty claims.

Jesco Lighting Official Website: www.jescolighting.com

© 2023 Jesco Lighting. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.