Hayward SPX0710XF Replacement Valve Handle Instruction Manual

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of the Hayward SPX0710XF Replacement Valve Handle. This handle is specifically designed to replace worn or broken handles on compatible Hayward multiport and sand filter valves, ensuring proper functionality of your pool filtration system.

2. Product Overview

The Hayward SPX0710XF is a durable replacement handle for various Hayward valve models. It is engineered to provide a secure grip and precise control over your filter's functions.

2.1 Compatibility

This replacement handle is compatible with the following Hayward valve models:

• Hayward Multiport Valve Models: SP0710, SP0710X, SP0711, SP0712
• Hayward Sand Filter Valve Series: Pro Series, VL Series, S200 Series

2.2 Product Image

Image of the Hayward SPX0710XF replacement valve handle, a black, curved plastic component designed for Hayward multiport and sand filter valves.

3. Safety Information

Always prioritize safety when working with pool equipment. Failure to follow these instructions can result in injury or damage to equipment.

• Disconnect Power: Before performing any maintenance or installation on your pool filter system, ensure all power to the pump is disconnected at the circuit breaker.
• Release Pressure: Always release any pressure in the filter system before opening or servicing the valve. Refer to your filter's manual for specific instructions on pressure release.
• Wear Protective Gear: Use appropriate personal protective equipment, such as safety glasses, when working with tools or pool chemicals.
• Consult a Professional: If you are unsure about any step or encounter difficulties, consult a qualified pool technician.

4. Setup and Installation

This section outlines the steps to replace your existing valve handle with the Hayward SPX0710XF.

1. Prepare the System:
   • Turn off the pool pump and disconnect power at the circuit breaker.
   • Ensure the filter system is depressurized.
2. Remove the Old Handle:
   • Locate the pin that secures the existing handle to the valve stem. This pin typically runs through the base of the handle and the stem.
   • Carefully push out or remove this pin. Depending on the design, you may need a small punch or screwdriver.
   • Once the pin is removed, the old handle can be lifted off the valve stem.
3. Install the New Handle:
   • Align the new Hayward SPX0710XF handle with the valve stem, ensuring the holes in the handle align with the hole in the stem.
   • Insert the securing pin through the aligned holes. Ensure the pin is fully seated and secure.
   • Gently test the handle's movement to confirm it rotates smoothly and engages the valve positions correctly.
4. Restore System:
   • Reconnect power to the pool pump.
   • Follow your filter system's instructions for repressurizing and restarting the system.
   • Check for any leaks around the valve.

Note: The exact method for pin removal and insertion may vary slightly depending on your specific valve model. Refer to your valve's original manual for detailed instructions if needed.

5. Operation

The valve handle controls the flow of water through your pool filter system. Each position corresponds to a specific function. Always turn off the pump before changing valve positions to prevent damage to the valve or filter.

5.1 Multiport Valve Positions (Common)

• FILTER: Normal filtering. Water flows through the filter media and returns to the pool.
• BACKWASH: Cleans the filter media. Water flows in reverse through the filter and out the waste line.
• RINSE: Used after backwashing to flush out any remaining dirt from the filter media and settle the media. Water flows through the filter and out the waste line.
• WASTE/DRAIN: Bypasses the filter. Used for vacuuming heavy debris directly to waste or lowering the pool water level.
• RECIRCULATE/BYPASS: Bypasses the filter. Water is circulated directly back to the pool without filtering.
• CLOSED: Shuts off all flow to the filter. Never operate the pump with the valve in the CLOSED position.
• WINTER/CLOSED: Used for winterizing the pool. This position typically lifts the diverter, preventing pressure buildup and allowing for drainage.

Refer to your specific Hayward multiport valve manual for detailed descriptions of each position and recommended operating procedures.

6. Maintenance

Proper maintenance of your valve handle ensures longevity and smooth operation of your pool filter system.

• Regular Inspection: Periodically inspect the handle for signs of wear, cracks, or damage. Replace the handle if it shows significant deterioration.
• Cleaning: Keep the handle and the valve top clean from debris, dirt, and chemical residue. A mild soap and water solution can be used.
• Lubrication (if applicable): While the handle itself typically does not require lubrication, the internal valve diverter may benefit from periodic lubrication with a silicone-based lubricant designed for pool equipment. Refer to your valve's manual for specific lubrication instructions.

7. Troubleshooting

This section addresses common issues related to the valve handle.

• Handle is Stiff or Hard to Turn:
  • Ensure the pump is off and the system is depressurized before attempting to turn the handle.
  • Inspect the valve's internal diverter for debris or wear. The diverter may need cleaning or lubrication.
  • Check if the handle's securing pin is bent or obstructed.
• Handle Feels Loose or Wobbly:
  • Verify that the securing pin is fully inserted and not damaged.
  • Inspect the valve stem for wear or damage where the handle attaches.
• Water Leaking from Handle Area:
  • This typically indicates an issue with the valve's internal components (e.g., spider gasket, O-rings) rather than the handle itself. The valve top may need to be serviced or replaced.

For issues beyond the handle, consult your Hayward multiport valve's specific troubleshooting guide or contact a qualified pool professional.

8. Specifications

Note on Weight: The provided product data indicates a weight of 7.5 lbs. This weight is unusually high for a small valve handle and likely refers to the entire valve assembly or is an error in the source data. The handle itself is significantly lighter.

9. Warranty and Support

Hayward products are manufactured to high standards. For specific warranty information regarding the SPX0710XF Replacement Valve Handle, please refer to the documentation included with your original Hayward valve or visit the official Hayward website.

For technical support, replacement parts, or further assistance, please contact Hayward Customer Service or your authorized Hayward dealer. When contacting support, have your product model number (SPX0710XF) and the model number of your multiport valve readily available.

Hayward Official Website: www.hayward-pool.com