Dynalon 607115 Polyethylene 150mL Flat Bottom Lab Sampling Scoop

Product Overview

The Dynalon 607115 Lab Sampling Scoop is a robust and versatile tool designed for accurate and safe handling of various materials in laboratory and industrial settings. Constructed from high-density polyethylene (HDPE), this scoop offers excellent chemical resistance and durability.

Key features include:

• 150mL Liquid Capacity: Ideal for precise measurement and transfer of liquids.
• High-Density Polyethylene (HDPE) Construction: Ensures durability, chemical resistance, and suitability for various substances.
• Flat Bottom Design: Allows the scoop to stand upright, preventing spills and facilitating easy filling and emptying.
• Heavy-Duty Build: Suitable for demanding industrial and laboratory applications.
• Versatile Use: Designed for both liquids and powders.

Figure 1: Dynalon 607115 Polyethylene 150mL Flat Bottom Lab Sampling Scoop. This image shows a clear, translucent polyethylene lab scoop with a flat bottom and a long handle, designed for sampling liquids and powders.

Setup and Initial Preparation

Before first use, and after each subsequent use, proper preparation ensures the integrity of your samples and the longevity of the scoop.

1. Unpacking: Carefully remove the scoop from its packaging. Inspect for any visible damage or defects that may have occurred during transit. If any damage is observed, do not use the scoop and contact your supplier.
2. Initial Cleaning: Wash the scoop thoroughly with a mild laboratory detergent and warm water. Rinse extensively with distilled or deionized water to remove all detergent residues.
3. Drying: Allow the scoop to air dry completely in a clean, dust-free environment, or use a lint-free cloth. Ensure no moisture remains, especially if the scoop will be used with moisture-sensitive materials.
4. Sterilization (Optional): If sterile conditions are required, the scoop can be sterilized using appropriate methods for polyethylene, such as ethylene oxide gas or chemical sterilization. Autoclaving is generally not recommended for polyethylene due to potential deformation at high temperatures.

Operating Instructions

The Dynalon 607115 scoop is designed for safe and efficient sampling and transfer of various materials.

For Powders and Granular Materials:

1. Preparation: Ensure the scoop is clean and dry, and that the material to be sampled is accessible.
2. Sampling: Gently insert the scoop into the material. For representative samples, ensure the scoop penetrates the material adequately.
3. Leveling (Optional): If a precise volume is required, use a straight edge (e.g., a spatula or another clean, flat object) to level off the material in the scoop.
4. Transfer: Carefully transfer the sampled material to the desired container, ensuring minimal spillage.

For Liquids:

1. Preparation: Ensure the scoop is clean and dry.
2. Submersion: Slowly submerge the scoop into the liquid until the desired volume is collected. The 150mL capacity can guide volume.
3. Withdrawal: Carefully withdraw the scoop, minimizing agitation of the liquid.
4. Transfer: Pour the liquid into the target container. The flat bottom design allows for stable placement if temporary holding is needed.

Important: Always use appropriate personal protective equipment (PPE) when handling chemicals or hazardous materials. Avoid cross-contamination by using a dedicated scoop for each material or by thoroughly cleaning between uses.

Maintenance and Care

Proper maintenance extends the life of your Dynalon scoop and ensures accurate performance.

• Cleaning: After each use, clean the scoop immediately to prevent material residue from drying and adhering. Use warm water and a mild, non-abrasive detergent. For stubborn residues, a soft brush may be used.
• Rinsing: Rinse thoroughly with distilled or deionized water to remove all cleaning agents.
• Drying: Air dry or wipe with a clean, lint-free cloth. Ensure complete dryness before storage.
• Storage: Store the scoop in a clean, dry, and dust-free environment, away from direct sunlight and extreme temperatures. Storing in a dedicated container or drawer can prevent scratches and contamination.
• Inspection: Periodically inspect the scoop for signs of wear, cracks, or chemical degradation. Discard and replace any damaged scoops to prevent sample contamination or inaccurate measurements.

Troubleshooting

Most issues with the Dynalon scoop relate to cleaning or material compatibility. Here are common concerns and their solutions:

Specifications

Detailed specifications for the Dynalon 607115 Polyethylene Lab Sampling Scoop:

• Model Number: DYNCR 607115
• Material: High-Density Polyethylene (HDPE)
• Capacity: 150mL (liquid)
• Bottom Type: Flat
• Applications: Industrial and laboratory sampling of liquids and powders
• Package Dimensions: Approximately 9.4 x 8.3 x 7 inches
• Item Weight: Approximately 5.09 Pounds (for case of 6)
• Manufacturer: Dynalon
• ASIN: B004AHL8ZA
• First Available: November 3, 2010