Fabbri Ellisse 6960810 Magnetic Ski and Snowboard Carrier

1. Introduction and Product Overview

The Fabbri Ellisse 6960810 is a magnetic ski and snowboard carrier designed for secure attachment to vehicle roofs. This carrier facilitates the transport of up to two pairs of skis, including carving or cross-country skis, or two snowboards. It features high-strength magnetic plates engineered to ensure stable and safe transport, even under challenging driving conditions. Special protective layers on the magnetic plates are integrated to prevent damage to your vehicle's paintwork. This product has successfully undergone City Crash Testing, affirming its structural integrity and safety performance.

Image showing the Fabbri Ellisse 6960810 magnetic ski and snowboard carrier installed on a car roof, ready for use.

2. Safety Information

Please read and understand all safety instructions before installing or using the Fabbri Ellisse 6960810 carrier. Failure to follow these instructions may result in property damage or personal injury.

• Always ensure the carrier is securely attached to the vehicle roof before commencing any journey.
• Do not exceed the maximum load capacity of the carrier or your vehicle's roof. Refer to the 'Specifications' section for carrier capacity.
• Regularly check the carrier's attachment and the security of the loaded items, especially during long trips or after driving on rough terrain.
• Drive at reduced speeds when the carrier is installed, particularly in adverse weather conditions such as strong winds, heavy rain, or snow.
• Avoid sudden braking, rapid acceleration, or sharp turns, as these can affect the stability of the carrier and its contents.
• Remove the carrier when it is not in use to prevent potential theft, reduce wind noise, and improve fuel efficiency.
• Thoroughly clean both the vehicle roof and the magnetic plates before each installation. This ensures maximum adhesion and prevents abrasive particles from damaging the vehicle's paint.
• Be aware of the increased height of your vehicle when the carrier is loaded, especially when entering garages, car washes, or low-clearance areas.

3. Package Contents

Verify that all components are present in the package before proceeding with installation:

• 2 x Fabbri Ellisse Magnetic Carrier Units
• 2 x Ski/Snowboard Holding Arms
• 1 x Key Set (for locking mechanisms, if applicable)
• 1 x User Manual (this document)

4. Setup and Installation

1. Prepare the Vehicle Roof: Thoroughly clean the area of the vehicle roof where the carrier units will be placed. Ensure the surface is completely dry and free from any dirt, dust, grit, or moisture. This step is critical for achieving optimal magnetic adhesion and preventing scratches or damage to your vehicle's paintwork.
2. Position the Carrier Units: Carefully place the two magnetic carrier units onto the desired positions on the vehicle roof. Ensure they are parallel to each other and spaced appropriately to accommodate the length of your skis or snowboards. The units should be placed on a flat, metallic surface of the roof.
3. Secure the Carrier: Press down firmly on each magnetic unit to ensure full and even contact with the roof surface. The high-strength magnets will engage and secure the units in place. Listen for a distinct 'snap' or feel a strong pull, indicating proper attachment.
4. Verify Stability: Gently attempt to move each carrier unit by hand. They should feel completely stable and immovable. If there is any noticeable movement or instability, lift the unit, re-clean the surface, and re-position it until a secure attachment is achieved.
5. Engage Locking Mechanisms (if applicable): If your carrier model includes integrated locking mechanisms, ensure they are engaged after the units are securely installed on the roof. This provides an additional layer of security.

5. Operating Instructions

1. Load Skis or Snowboards: Unlock and open the holding arms of the carrier units. Carefully place your skis or snowboards onto the carrier, ensuring they are centered and balanced between the two units. For skis, place them with bindings facing upwards. Snowboards should be placed flat on the carrier surface.
2. Secure Items: Close the holding arms firmly over the skis or snowboards. Ensure that the items are tightly clamped and cannot shift or move within the carrier. The arms should close completely and securely.
3. Lock the Carrier: Use the provided key (if applicable) to lock the holding arms. This prevents accidental opening during transit and deters theft of your equipment.
4. Pre-Drive Check: Before starting your journey, gently shake the loaded skis or snowboards to confirm they are absolutely secure. After driving a short distance (e.g., 5-10 km), stop and re-check the security of both the carrier units and the loaded items. Repeat this check periodically during longer trips.
5. Driving with Carrier: Maintain reduced speeds, especially when encountering strong winds, heavy precipitation, or uneven road surfaces. Avoid sudden or aggressive driving maneuvers to ensure the stability of the carrier and its contents.

6. Maintenance

Proper maintenance will extend the life and ensure the continued safe operation of your Fabbri Ellisse carrier.

• Cleaning: After each use, particularly after exposure to road salt, snow, or dirt, clean the magnetic plates and all carrier components with mild soap and water. Rinse thoroughly with clean water and dry completely with a soft cloth.
• Inspection: Regularly inspect the magnetic plates for any signs of wear, damage, or embedded debris. Ensure the protective layers are intact. Replace any damaged components immediately.
• Moving Parts: Check all hinges, pivots, and locking mechanisms for smooth operation. If necessary, apply a small amount of silicone-based lubricant to ensure they function correctly.
• Storage: When not in use, store the carrier in a clean, dry environment, away from direct sunlight and extreme temperatures.

7. Troubleshooting

Problem: Carrier does not adhere securely to the vehicle roof.

Solution: Ensure both the vehicle roof surface and the magnetic plates on the carrier are perfectly clean, dry, and free of any dirt, dust, or moisture. Even small particles can significantly reduce magnetic adhesion. Re-position the carrier and apply firm, even pressure to ensure full contact.

Problem: Skis or snowboards are loose or shifting during transport.

Solution: Re-open the holding arms and re-position the items. Ensure they are centered and balanced. Close the arms tightly and verify that the locking mechanism (if present) is fully engaged. Confirm that the number and type of items loaded are within the carrier's specified capacity.

Problem: Marks or damage appear on the vehicle's paintwork after using the carrier.

Solution: This issue typically arises from dirt, dust, or abrasive particles trapped between the magnetic plate and the car's roof. Always ensure both surfaces are spotless before installation. As an additional precautionary measure, some users have found success by placing a thin, clear protective film (e.g., kitchen cling film) between the magnetic plates and the car's paintwork. While not an official manufacturer recommendation, this can provide an extra layer of protection against micro-scratches.

8. Specifications

9. Warranty and Support

For detailed information regarding the product warranty, terms, and conditions, please refer to the specific warranty documentation included with your purchase. In case of any questions, technical issues, or to claim warranty service, please contact Fabbri customer support directly. It is recommended to retain your proof of purchase (receipt or invoice) as it may be required for warranty claims.