RV Designer G825 3/4 inch Angled Gas Prop Bracket Instruction Manual

1. Product Overview

The RV Designer G825 is a 3/4 inch angled gas prop bracket designed for securely affixing gas props or strut/springs in recreational vehicles. This bracket features a 10mm ball stud for compatibility with various gas props and is supplied in a pack of two, including necessary fasteners for installation.

Image 1.1: The RV Designer G825 3/4 inch Angled Gas Prop Bracket, featuring a 10mm ball stud and a black finish.

2. Product Features

• Angled Design: 3/4 inch angled bracket for versatile mounting options.
• Ball Stud: Equipped with a 10mm ball for secure attachment of gas props.
• Application: Specifically designed to affix gas props or strut/springs in RVs.
• Quantity: Supplied as a 2-pack for convenience.
• Includes Fasteners: Comes with necessary hardware for installation.

3. Installation Instructions

Proper installation of the RV Designer G825 bracket is essential for safe and effective operation of your gas prop. Ensure you have the correct tools and follow all safety precautions.

3.1 Tools Required

• Drill
• Drill bits appropriate for fasteners
• Screwdriver or wrench (depending on fastener type)
• Measuring tape
• Pencil or marker
• Safety glasses

3.2 Installation Steps

1. Determine Mounting Location: Identify the precise location where the gas prop bracket needs to be installed. This location should provide optimal leverage and support for the gas prop, ensuring smooth operation of the door, hatch, or lid.
2. Mark Drill Points: Place the bracket in the desired position and use a pencil or marker to mark the locations for drilling pilot holes through the bracket's mounting holes.
3. Drill Pilot Holes: Using an appropriate drill bit, carefully drill pilot holes at the marked locations. Ensure the pilot holes are slightly smaller than the diameter of the fasteners to allow for a secure fit.
4. Secure the Bracket: Align the bracket with the pilot holes and insert the provided fasteners. Use a screwdriver or wrench to tighten the fasteners securely. Do not overtighten, as this may strip the material or damage the bracket.
5. Attach Gas Prop: Once the bracket is firmly mounted, attach the gas prop's socket end to the 10mm ball stud on the bracket. Ensure the connection is secure and the gas prop moves freely.
6. Test Operation: Carefully test the operation of the door, hatch, or lid to ensure the gas prop functions correctly and provides the intended support.

3.3 Selecting a Compatible Gas Prop

The G825 bracket is designed to work with gas props featuring a 10mm ball socket. When selecting a gas prop, consider the required length and force for your specific application. Refer to the gas prop selector guide for assistance.

Image 3.1: Gas Prop Selector Guide - Step 1: Measure the length of the fully extended gas prop from center of ball cap to center of ball cap.

Image 3.2: Gas Prop Selector Guide - Step 3: Locate the length and force of your prop to select the right replacement. Example: Length is 14" and Force is 40 pounds or 175-185 newtons select prop 9.

Image 3.3: Gas Prop Selector Guide Table - Part 1, showing RVD #, Selection #, Length/Force, and Force in Newtons for various gas props.

Image 3.4: Gas Prop Selector Guide Table - Part 2, continuing the list of RVD #, Selection #, Length/Force, and Force in Newtons for various gas props.

4. Operating the Bracket

The RV Designer G825 bracket serves as a fixed mounting point for a gas prop. Once installed, its operation is passive, providing a secure pivot for the gas prop to support or assist in opening and closing RV doors, hatches, or lids. Ensure the gas prop is correctly attached to the 10mm ball stud for proper function.

5. Maintenance

• Regular Inspection: Periodically inspect the bracket and its fasteners for any signs of looseness, corrosion, or damage.
• Cleaning: Clean the bracket with a mild soap and water solution if dirt or grime accumulates. Avoid abrasive cleaners that could damage the finish.
• Tighten Fasteners: If any fasteners appear loose, gently tighten them to ensure the bracket remains securely mounted.
• Lubrication: The ball stud typically does not require lubrication, but ensure the gas prop's socket connection remains clean and free of debris.

6. Troubleshooting

• Bracket is Loose: Check all mounting fasteners and tighten them if necessary. Ensure the mounting surface is stable and not compromised.
• Gas Prop Detaches from Ball Stud: Verify that the gas prop's socket is fully seated onto the 10mm ball stud. If the gas prop is old or damaged, its socket may be worn and require replacement.
• Bracket Appears Damaged: If the bracket shows signs of bending, cracking, or severe corrosion, it should be replaced immediately to prevent failure.

7. Specifications

8. Warranty and Support

RV Designer is committed to the quality and durability of its products. The brand offers a Lifetime Commitment, ensuring that if an RV Designer product fails to provide the expected benefit, it will be replaced.

Image 8.1: RV Designer's Lifetime Commitment statement, emphasizing product replacement for failures.

For product support, inquiries, or to claim warranty service, please contact RV Designer directly through their official channels. Visit the RV Designer Store for more information.