Aurabeam XL-5200 KDS-55A2000 Replacement Lamp with Housing User Manual

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Aurabeam XL-5200 KDS-55A2000 replacement lamp with housing. This product is designed for use with compatible Sony rear projection televisions. Please read these instructions thoroughly before proceeding with installation.

2. Safety Information

• Always unplug the television from the power outlet before attempting any installation or maintenance. Failure to do so can result in electric shock.
• Allow the television and the old lamp to cool down completely before handling. Lamps can become extremely hot during operation.
• Do not touch the glass surface of the new lamp bulb with bare hands. Oils from your skin can reduce lamp life and performance. Use gloves or a clean cloth if accidental contact occurs.
• Handle the lamp housing carefully to avoid damage.
• The lamp contains mercury. Dispose of the old lamp according to local environmental regulations. Do not discard with regular household waste.
• Keep out of reach of children.

3. Package Contents

Verify that your package contains the following item:

• 1 x Aurabeam XL-5200 KDS-55A2000 Replacement Lamp with Housing

Image: Aurabeam replacement lamp packaging box.

4. Setup and Installation

Refer to your Sony television's original user manual for specific lamp replacement instructions. The following steps are general guidelines:

1. Power Off and Unplug: Ensure the television is turned off and completely unplugged from the power outlet.
2. Cool Down: Allow the television and the old lamp to cool for at least 30 minutes to prevent burns.
3. Locate Access Panel: Identify the lamp access panel, typically located on the bottom right side or rear of your Sony rear projection TV.
4. Remove Panel: Carefully remove the screws or latches securing the lamp access panel and set it aside.
5. Extract Old Lamp: Gently pull out the old lamp unit from its compartment. It may require a slight tug or wiggle to disengage.
6. Insert New Lamp: Align the new Aurabeam replacement lamp with housing into the compartment. Push it firmly and completely until it is securely seated. Ensure the electrical connectors are properly engaged.
7. Replace Panel: Reattach the lamp access panel and secure it with the screws or latches removed earlier.
8. Power On: Plug the television back into the power outlet.

Image: Angled view of the Aurabeam XL-5200 replacement lamp with housing.

Image: Front view of the lamp bulb within the housing.

Image: Rear view of the lamp housing, showing the ventilation grid.

Image: Side view of the lamp housing, highlighting the electrical connectors.

5. Operating Instructions

After installing the new lamp, it is recommended to reset the lamp timer in your television's service menu. Consult your Sony TV's user manual for specific instructions on how to access and reset the lamp timer. Resetting the timer ensures accurate tracking of the new lamp's operational hours.

6. Maintenance

• Handling: Always handle the lamp by its housing. Avoid touching the glass bulb directly.
• Disposal: Due to the mercury content, the old lamp must be disposed of responsibly. Check with your local waste management facility for proper recycling or disposal procedures for mercury-containing products.
• Cleaning: Do not attempt to clean the lamp bulb. If the housing requires cleaning, use a dry, soft cloth.

7. Troubleshooting

• No Picture / TV Not Turning On:
  • Ensure the new lamp unit is fully and correctly seated in its compartment.
  • Verify that the lamp access panel is securely closed and all screws/latches are fastened. Some TVs have safety switches that prevent operation if the panel is open.
  • Confirm the television is properly plugged into a working power outlet.
• Dim Picture / Poor Color Quality:
  • Reset the lamp timer in your TV's menu. An un-reset timer might cause the TV to operate as if the old, worn lamp is still in use.
  • Check TV picture settings (brightness, contrast, color) to ensure they are optimized.
• Flickering / Intermittent Power Cycling:
  • Ensure the lamp is fully seated and its connectors are firm.
  • This could indicate a faulty lamp or an issue with the television's power supply or ballast. If the issue persists after re-seating the lamp, contact support.

8. Specifications

9. Warranty Information

For detailed warranty information regarding your Aurabeam replacement lamp, please refer to the product packaging or visit the official Aurabeam website. Warranty terms and conditions may vary.

10. Support

If you encounter any issues not covered in this manual or require further assistance, please contact Aurabeam customer service. Contact information can typically be found on the product packaging or the official Aurabeam website.