Anzo USA 221147 Honda Civic Red/Clear Tail Light Assembly

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your Anzo USA 221147 Honda Civic Red/Clear Tail Light Assembly. This product is designed as a direct replacement for factory lenses and is SAE (Society of Automotive Engineers) and D.O.T. (Department of Transportation) compliant with FMVSS No. 108, ensuring safety and quality standards are met.

Please read this manual thoroughly before installation to ensure correct procedure and optimal performance.

2. Safety Information

• Always disconnect the vehicle's battery before performing any electrical work to prevent electrical shock or damage.
• Wear appropriate personal protective equipment (PPE), such as gloves and eye protection, during installation.
• Ensure the vehicle is parked on a level surface with the parking brake engaged.
• If you are unsure about any step of the installation process, consult a qualified automotive technician.
• This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning). Handle with care and wash hands after handling.

3. Package Contents

Verify that all components are present and undamaged before beginning installation.

• Anzo USA 221147 Honda Civic Red/Clear Tail Light Assembly (Sold in Pairs)
• Gaskets/Seals (pre-attached or included)
• Mounting hardware (if not integrated)

Note: Bulbs may or may not be included depending on the specific package. Retain original bulbs if new ones are not provided.

4. Specifications

5. Setup and Installation

This tail light assembly is designed for easy installation, directly replacing your vehicle's factory lenses. Basic hand tools are typically required.

5.1 Tools Required (Typical)

• Screwdriver set (Phillips and Flathead)
• Socket wrench set
• Plastic trim removal tool (optional, but recommended)

5.2 Installation Steps

1. Prepare the Vehicle: Park the vehicle on a level surface, engage the parking brake, and turn off the engine. Open the trunk or tailgate to access the tail light area.
2. Disconnect Battery (Optional but Recommended): For safety, disconnect the negative terminal of the vehicle's battery.
3. Access Mounting Bolts: Locate the mounting bolts or nuts that secure the existing tail light assembly. These are typically accessible from inside the trunk or behind a trim panel. Remove any trim panels if necessary.
4. Remove Old Tail Light: Carefully remove the mounting bolts/nuts. Gently pull the old tail light assembly away from the vehicle. It may be held in place by alignment pins or clips.
5. Disconnect Wiring: Twist and remove the bulb sockets from the old tail light housing. If the new assembly includes bulbs, transfer the wiring harness. If not, transfer your existing bulbs to the new assembly.
6. Inspect New Assembly: Before installation, inspect the new Anzo USA tail light assembly for any damage.

Figure 1: Front view of the Anzo USA 221147 Honda Civic Red/Clear Tail Light Assembly, showing the red and clear lens sections.
7. Connect Wiring to New Assembly: Insert the bulb sockets into the corresponding openings on the new Anzo USA tail light assembly, twisting them to secure. Ensure a snug fit.


Figure 2: Rear view of the Anzo USA 221147 Honda Civic Red/Clear Tail Light Assembly, illustrating the bulb socket receptacles and mounting studs.

8. Mount New Tail Light: Carefully align the new tail light assembly with the vehicle's body and push it into place. Ensure the alignment pins (if present) engage correctly.
9. Secure Mounting Bolts: Reinstall and tighten the mounting bolts/nuts. Do not overtighten, as this can crack the plastic housing.
10. Reconnect Battery: Reconnect the negative terminal of the vehicle's battery.
11. Test Functionality: Turn on the vehicle's ignition and test all tail light functions: running lights, brake lights, turn signals, and reverse lights. Ensure all lights illuminate correctly and without flickering.
12. Reinstall Trim Panels: Reinstall any interior trim panels removed during the process.

6. Operating Instructions

Once properly installed, the Anzo USA 221147 Tail Light Assembly operates automatically with your vehicle's electrical system. Ensure your vehicle's lighting controls are functioning correctly to activate the tail lights, brake lights, and turn signals as intended.

• Running Lights: Activate when the vehicle's headlights or parking lights are on.
• Brake Lights: Illuminate when the brake pedal is pressed.
• Turn Signals: Flash when the turn signal lever is engaged.
• Reverse Lights: Illuminate when the vehicle is shifted into reverse gear.

7. Maintenance

• Cleaning: Clean the tail light lenses regularly with a soft cloth and mild automotive soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the lens material.
• Inspection: Periodically inspect the tail light assembly for any signs of damage, cracks, or moisture intrusion. Check that all bulbs are functioning correctly.
• Bulb Replacement: If a bulb fails, replace it with a bulb of the correct type and wattage as specified by your vehicle manufacturer. Refer to your vehicle's owner's manual for bulb specifications and replacement procedures.

8. Troubleshooting

9. Warranty and Support

Specific warranty information for Anzo USA products is typically provided at the point of purchase or on the manufacturer's official website. Please retain your proof of purchase for any warranty claims.

For technical support or further assistance, please refer to the ANZO USA official website or contact their customer service department. Contact details are not provided in this manual but can usually be found on the product packaging or the manufacturer's website.