JR Products 13025 Black DPDT On/Off/On Momentary Switch User Manual

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your JR Products 13025 Black DPDT On/Off/On Momentary Switch. Please read this manual thoroughly before installation and use, and retain it for future reference.

The JR Products 13025 is a Double Pole Double Throw (DPDT) momentary switch designed for applications requiring an On/Off/On function, commonly used in RVs for hydraulic slide-out rooms. It features a robust design and is UL/CSA approved for reliable performance.

2. Safety Information

WARNING: Electrical work should only be performed by qualified personnel. Failure to follow these instructions may result in electrical shock, fire, or serious injury.

• Always disconnect power to the circuit before installing, servicing, or removing the switch.
• Ensure all wiring connections are secure and comply with local electrical codes.
• Do not exceed the specified electrical ratings of the switch (8A @ 125 VAC, 1/2 HP @ 125-250 VAC, 9A @ 14 VDC).
• Protect the switch from moisture and extreme temperatures unless specifically rated for such conditions.

3. Product Overview

3.1 Key Features

• DPDT (Double Pole Double Throw) configuration.
• On/Off/On momentary action.
• Electrical Ratings: 8 Amp @ 125 VAC, 1/2 H.P. @ 125-250 VAC, 9 Amp @ 14 VDC.
• UL/CSA approved for safety and quality.
• Black finish.

3.2 Components

The JR Products 13025 switch consists of a durable housing, an actuator (push button), and multiple terminals for electrical connections. The momentary action means the switch returns to the 'Off' (center) position when the actuator is released.

Figure 1: JR Products 13025 Black DPDT On/Off/On Momentary Switch. This image shows the black switch housing and the copper terminals extending from the side.

4. Setup and Installation

4.1 Tools Required

• Wire strippers/cutters
• Screwdriver (appropriate for terminal screws)
• Drill and appropriate bit (if creating a new mounting hole)
• Measuring tape or ruler
• Safety glasses

4.2 Installation Steps

1. Disconnect Power: Ensure all power to the circuit where the switch will be installed is completely disconnected at the source.
2. Prepare Mounting Location: If replacing an existing switch, carefully remove the old switch. If installing in a new location, create a cutout with dimensions of approximately 0.670 inches (width) by 0.500 inches (height). The overall switch dimensions are 1.285 inches by 0.830 inches.
3. Wire Connections: Identify the appropriate wires for your application (e.g., power input, output for 'On 1', output for 'On 2'). The switch uses screw terminals. Strip approximately 1/4 inch of insulation from each wire and securely connect them to the corresponding terminals. Refer to your specific application's wiring diagram for correct terminal assignments.
4. Mount the Switch: Insert the switch into the prepared cutout. Ensure it is seated firmly. The switch is designed to snap into place or be secured by its housing.
5. Restore Power: Once the switch is securely mounted and all connections are verified, restore power to the circuit.
6. Test Functionality: Test the switch to ensure it operates correctly for your intended application.

5. Operating Instructions

The JR Products 13025 is an On/Off/On momentary switch. This means it has three positions:

• Center Position: This is the 'Off' position. When the switch is not being pressed, it will return to this position, and no circuit will be active.
• Up Position (Momentary): Pressing the switch upwards activates one circuit. The switch will return to the 'Off' position when released.
• Down Position (Momentary): Pressing the switch downwards activates a different circuit. The switch will return to the 'Off' position when released.

To operate, simply press the switch in the desired direction (up or down) to activate the corresponding function. Release the switch to return to the neutral 'Off' state.

6. Maintenance

The JR Products 13025 switch is designed for durability and requires minimal maintenance.

• Cleaning: Periodically wipe the switch surface with a clean, dry cloth to remove dust and debris. Avoid using harsh chemicals or abrasive cleaners.
• Inspection: Regularly inspect the switch for any signs of physical damage, loose connections, or unusual operation. If any issues are found, disconnect power and address them promptly.
• Environmental Protection: Ensure the switch is not exposed to conditions beyond its IP54 rating, which indicates protection against dust ingress and splashing water.

7. Troubleshooting

If you experience issues with your switch, consider the following common troubleshooting steps:

• Switch Not Activating:
  • Check if power is supplied to the circuit.
  • Verify all wire connections are secure and correctly terminated.
  • Ensure the switch is not damaged internally.
• Intermittent Operation:
  • Inspect for loose wiring connections.
  • Check for corrosion on terminals.
• Switch Stuck:
  • Ensure no foreign objects are obstructing the switch mechanism.
  • If the switch mechanism is physically damaged, replacement may be necessary.

If troubleshooting does not resolve the issue, contact a qualified electrician or the manufacturer for assistance.

8. Technical Specifications

9. Warranty and Support

Specific warranty information for the JR Products 13025 switch is not provided in this manual. For details regarding warranty coverage, returns, or technical support, please refer to the product packaging, the retailer where the product was purchased, or contact JR Products directly through their official website or customer service channels.