Introduction
This manual provides detailed instructions for the installation, adjustment, and maintenance of your Salice Excen-Three 106 Degree Opening, 1/2 Inch Overlay Hinges. These self-closing hinges are designed for face frame cabinet applications and feature a 3-cam adjustment system for precise door alignment. Please read these instructions carefully before beginning installation.
Safety Information
- Always wear appropriate personal protective equipment, such as safety glasses, during installation.
- Keep small parts and tools out of reach of children.
- Ensure all screws are securely fastened to prevent injury or damage.
- Use the correct tools for each step to avoid damaging the hinges or cabinet.
Package Contents
Verify that all components are present before beginning installation:
- 2 x Salice Excen-Three Hinges
- Mounting Screws (for both hinge cup and face frame plate)
This image displays two Salice Excen-Three hinges, designed for a 106-degree opening and 1/2-inch overlay. They are made of steel with a nickel finish. A small pile of mounting screws is also visible, indicating that they are included with the hinges.
Specifications
| Brand | Salice |
| Model Number | CECOMINOD027120 |
| Material | Steel |
| Finish Type | Nickel |
| Mounting Type | Face Mount |
| Opening Angle | 106 Degrees |
| Overlay | 1/2 inch (13mm) |
| Bore Diameter | 35mm |
| Cup Depth | 7/16 inch |
| Adjustment | 3-cam (Height, Depth, Side-to-Side) |
| Drilling Distance | 3/32 inch (2.5mm) |
| Style | Self Closing |
| Number of Pieces | 2 |
Installation Instructions
Tools Required
- Drill with 35mm Forstner bit
- Phillips head screwdriver
- Measuring tape or ruler
- Pencil
- Optional: Kreg Jig or similar drilling guide for consistent bore hole placement
Step-by-Step Installation
These hinges are designed for face frame applications only.
- Prepare the Cabinet Door: Mark the position for the 35mm bore hole on the inside of the cabinet door. The drilling distance (distance from the edge of the door to the edge of the bore hole) should be 3/32 inch (2.5mm). Use a 35mm Forstner bit to drill the bore hole to a depth of 7/16 inch.
- Attach Hinge Cup: Place the hinge cup into the drilled bore hole. Ensure the hinge is flush with the door surface. Secure the hinge cup to the door using the provided screws.
- Prepare the Face Frame: Position the cabinet door against the cabinet opening to determine the exact placement of the hinge mounting plate on the face frame. Mark the screw holes for the mounting plate.
- Mount Hinge Plate: Attach the hinge mounting plate to the cabinet face frame using the provided screws.
- Attach Door to Cabinet: Align the hinge arm with the mounting plate and click or slide it into place. Some hinges may require tightening a screw to secure the arm to the plate.
Adjustment
The Salice Excen-Three hinges feature a 3-cam adjustment system, allowing for precise alignment of your cabinet doors after installation. Use a Phillips head screwdriver for these adjustments.
- Side-to-Side Adjustment: This adjustment moves the door left or right relative to the cabinet opening. Locate the screw closest to the cabinet edge on the hinge arm. Turning this screw clockwise or counter-clockwise will shift the door horizontally.
- Depth Adjustment: This adjustment moves the door in or out, controlling the gap between the door and the cabinet frame. Locate the screw typically found in the middle of the hinge arm. Turning this screw will adjust the door's depth.
- Height Adjustment: This adjustment moves the door up or down. This is usually achieved by loosening the screws that attach the hinge plate to the face frame, adjusting the door to the desired height, and then re-tightening the screws. Some hinge plates may have dedicated height adjustment screws.
Make small adjustments to one hinge at a time and then check the door's alignment. Repeat as necessary until the desired fit is achieved.
Maintenance
Proper maintenance ensures the longevity and smooth operation of your Salice hinges.
- Cleaning: Wipe hinges periodically with a soft, damp cloth to remove dust and grime. Avoid abrasive cleaners or harsh chemicals, which can damage the nickel finish.
- Lubrication: If hinges begin to squeak or feel stiff, apply a small amount of silicone-based lubricant to the pivot points. Do not use oil-based lubricants, as they can attract dust and debris.
- Tightening: Periodically check all mounting screws and adjustment screws for tightness. Re-tighten any loose screws to maintain proper door alignment and function.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Door does not close completely or is misaligned. | Incorrect hinge adjustment. | Refer to the "Adjustment" section and adjust the side-to-side, depth, and height screws as needed. |
| Door sags or rubs against the cabinet frame. | Loose mounting screws or incorrect height adjustment. | Tighten all mounting screws. Adjust the height of the door using the height adjustment feature or by loosening and re-tightening the hinge plate screws. |
| Hinges squeak during operation. | Lack of lubrication or debris. | Clean the hinges and apply a small amount of silicone-based lubricant to the pivot points. |
Warranty Information
Specific warranty details for Salice Excen-Three hinges are typically provided by the manufacturer or the authorized seller at the time of purchase. Please retain your proof of purchase for any warranty claims. For detailed warranty terms and conditions, refer to the documentation included with your product or visit the official Salice website.
Customer Support
If you require further assistance with installation, adjustment, or troubleshooting, please contact Salice customer support or the retailer from whom you purchased the hinges. Have your product model number (CECOMINOD027120) and purchase information ready when contacting support.
For more information, you may visit the official Salice website: www.salice.com
