Kohler K-9055-0 Salient 60" x 36" Shower Base Instruction Manual

Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your Kohler K-9055-0 Salient 60" x 36" Shower Base. Please read these instructions thoroughly before beginning installation or use to ensure safety and optimal performance. This shower base is designed for durability and functionality, featuring enameled cast iron construction and a center drain.

Image: The Kohler K-9055-0 Salient 60" x 36" Shower Base in white, featuring a textured bottom and a central drain opening.

Setup and Installation

The Kohler K-9055-0 Salient shower base is designed for alcove installation with a center drain. Due to its weight and specific installation requirements, professional installation is highly recommended. Ensure all local plumbing and building codes are followed.

Pre-Installation Checks:

• Inspect the shower base for any damage prior to installation. Do not install a damaged unit.
• Verify that the subfloor is level and capable of supporting the weight of the shower base (approximately 250 pounds) plus water and user weight.
• Confirm rough-in dimensions and drain location match the product specifications.

Installation Steps (Summary - Consult Professional Installer):

1. Prepare the alcove area, ensuring walls are plumb and square.
2. Install the drain assembly according to the manufacturer's instructions.
3. Set the shower base into a mortar bed or equivalent leveling compound to ensure full support and proper drainage slope.
4. Connect the drain to the plumbing system, ensuring watertight seals.
5. Secure the shower base to the wall studs as required.
6. Perform a leak test before proceeding with wall finishes.

Image: Technical drawing illustrating the dimensions and flange detail of the Kohler K-9055-0 Salient 60" x 36" Shower Base, including drain location and diameter.

Operating Instructions

The Kohler K-9055-0 Salient shower base functions as the foundation for your shower enclosure. Once properly installed, its operation is straightforward:

• Ensure the drain is clear of debris before and after each use to prevent water accumulation.
• The textured surface provides slip resistance; however, exercise caution when entering and exiting the shower.
• After showering, allow water to fully drain and consider wiping down the surface to minimize water spots and soap scum buildup.

Maintenance and Care

Proper care will preserve the glossy finish and extend the life of your enameled cast iron shower base.

Routine Cleaning:

• Clean the shower base regularly with a mild, non-abrasive cleaner and a soft cloth or sponge.
• Rinse thoroughly with warm water after cleaning to remove all cleaner residue.
• For stubborn stains, consult Kohler's official cleaning recommendations for enameled cast iron.

Avoid:

• Abrasive cleaners, scouring pads, or steel wool, as these can scratch and dull the glossy finish.
• Strong chemical cleaners, especially those containing harsh acids or alkalis, which can damage the enamel.
• Leaving standing water in the base for extended periods.

Troubleshooting

This section addresses common issues you might encounter with your shower base.

Slow Drainage:

• Cause: Hair, soap scum, or other debris obstructing the drain.
• Solution: Remove the drain cover and clear any visible obstructions. Use a drain snake or a chemical drain cleaner specifically safe for plumbing systems, following product instructions carefully.

Surface Stains/Discoloration:

• Cause: Mineral deposits from hard water, prolonged contact with certain chemicals, or inadequate cleaning.
• Solution: Use a non-abrasive cleaner designed for enameled surfaces. For mineral deposits, a solution of white vinegar and water can be effective, followed by thorough rinsing.

Chips or Cracks in Enamel:

• Cause: Impact from heavy objects or improper installation.
• Solution: Small chips may be repaired with an enamel repair kit. For significant damage, consult a professional or Kohler customer service for advice on repair or replacement.

Specifications

Warranty Information

Kohler products are manufactured to high-quality standards and are backed by a limited warranty. Specific warranty terms and conditions may vary by product and region. For detailed warranty information pertaining to your Kohler K-9055-0 Salient Shower Base, please refer to the warranty documentation included with your purchase or visit the official Kohler website.

Customer Support

For further assistance, technical support, or to inquire about replacement parts, please contact Kohler customer service:

• Website: Visit www.kohler.com for product information, FAQs, and support resources.
• Phone: Refer to the Kohler website or your product packaging for the most current customer service contact numbers in your region.

When contacting support, please have your model number (K-9055-0) and purchase date available.