1. Introduction
The Pyle PSPVC6 is a 6-zone channel speaker switch selector with individual volume control, designed to distribute audio from a multi-channel amplifier to up to six pairs of speakers. This unit allows for independent volume adjustment and on/off control for each speaker zone, providing flexible audio management for various listening environments.
2. Safety Information
- Ensure all connections are secure before operating the unit.
- Do not exceed the maximum power handling capacity of 100 watts per channel.
- Connect only speaker systems with a minimum impedance of 8 ohms to prevent damage to your amplifier. Note: Connecting multiple speaker pairs can lower the overall impedance. Refer to your amplifier's specifications for safe operating impedance ranges.
- Avoid exposing the unit to moisture or extreme temperatures.
- Do not attempt to open or service the unit yourself. Refer all servicing to qualified personnel.
3. Package Contents
- Pyle PSPVC6 6-Zone Speaker Selector
- User Manual
4. Features
- 6-channel speaker selector with individual volume controls.
- Supports up to six pairs of speakers.
- Handles 100 watts per channel.
- Compatible with speaker systems having a minimum impedance of 8 ohms.
- Rugged and durable housing with cabinet heatsink for heat dissipation.
- Easy to read labels for controls and terminals.
- Protection circuitry to ensure smooth operation.
Figure 1: Key Features of the PSPVC6 Speaker Selector.
5. Product Overview
Figure 2: Top, Front, and Back Views of the PSPVC6.
Figure 3: Front Panel Controls and Features.
The front panel features individual volume control knobs for each of the six speaker zones, along with an "ALL SPEAKERS ON/OFF" switch. The rear panel provides speaker terminals for connecting your amplifier and up to six pairs of speakers.
6. Setup and Connections
- Prepare Speaker Wires: Strip approximately 1/2 inch (1.2 cm) of insulation from the ends of your speaker wires. Ensure there are no stray wire strands that could cause short circuits.
- Connect Amplifier: Connect the speaker output terminals from your amplifier to the "AMPLIFIER INPUT" terminals on the rear of the PSPVC6. Match positive (+) and negative (-) terminals correctly.
- Connect Speakers: Connect each pair of speakers to the corresponding "SPEAKER 1" through "SPEAKER 6" output terminals on the rear of the PSPVC6. Maintain correct polarity (positive to positive, negative to negative).
- Power On: The PSPVC6 is a passive device and does not require external power. It draws power directly from your amplifier. Once all connections are made, you can power on your amplifier.
Figure 4: Rear Panel Connections.
Important Note on Impedance: The PSPVC6 is designed for speaker systems with a minimum impedance of 8 ohms. When connecting multiple speaker pairs, the overall impedance presented to your amplifier will decrease. For example, if all 6 speaker pairs are active, the impedance can drop significantly (e.g., to 1.7 ohms). Ensure your amplifier is capable of safely driving the combined load. Consult your amplifier's manual for its minimum safe operating impedance.
7. Operating Instructions
- Turn On/Off All Speakers: Use the "ALL SPEAKERS ON/OFF" switch on the front panel to globally enable or disable all connected speaker zones.
- Select Speaker Zone: Each speaker zone (1-6) has an individual ON/OFF switch. Flip the switch to the "ON" position to activate a specific speaker pair.
- Adjust Volume: Rotate the corresponding volume knob for each active speaker zone to adjust its output level independently. Turn clockwise to increase volume and counter-clockwise to decrease.
- Source Selection (A/B): If your amplifier has A/B speaker outputs, you can connect them to the A and B inputs on the PSPVC6 (if available on your model, verify connections). This allows you to switch between two different audio sources for each speaker zone.
Figure 5: Global On/Off Switch and Volume Control.
Figure 6: Adjusting Individual Zone Volume.
Video 1: Product Overview and Basic Operation of the Pyle 6-Zone Speaker Selector.
8. Maintenance
- Keep the unit clean by wiping it with a soft, dry cloth.
- Do not use liquid cleaners or aerosol sprays.
- Ensure proper ventilation around the unit to prevent overheating.
9. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound from speakers. |
|
|
| Distorted sound. |
|
|
| Sound from only some speakers. |
|
|
10. Specifications
- Model: PSPVC6
- Channels: 6-Zone (6 pairs of speakers)
- Power Handling: 100 Watts per channel
- Minimum Speaker Impedance: 8 Ohms
- Product Dimensions (L x W x H): 16.92" x 6.29" x 3.03" (43 x 16 x 7.7 cm)
- Item Weight: 1 lbs (0.45 kg)
- Color: Black
- Connector Type: Speaker Wire Terminals
11. Warranty and Support
For warranty information and technical support, please refer to the official Pyle website or contact their customer service department. Keep your purchase receipt for warranty claims.
Pyle Website: www.pyleusa.com
