1. Product Overview
The CRC 05350 Belt Conditioner is formulated to enhance the performance and extend the lifespan of various belt types. It effectively addresses common belt issues such as squeaking, slippage, and glazing by removing accumulated oil, grease, and glaze from the belt surface. Regular application helps maintain optimal belt condition.
- Suitable for serpentine, flat, and V-type belts.
- Helps eliminate belt squeaks.
- Prevents belt slippage and glazing.
- Removes oil, grease, and glaze from belt surfaces.
- Contributes to prolonging overall belt life.
Image 1.1: Front view of the CRC 05350 Belt Conditioner can, showing the product name and key benefits.
2. Safety Information
WARNING: Read entire label before using this product. Failure to do so may result in serious injury or property damage.
- Extremely Flammable: Keep away from heat, sparks, open flames, and hot surfaces. No smoking.
- Harmful or Fatal if Swallowed: Do not ingest. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting.
- Eye and Skin Irritant: Avoid contact with eyes and skin. In case of contact, flush with water for several minutes. If irritation persists, seek medical attention.
- Contents Under Pressure: Do not puncture or incinerate container. Do not expose to heat or store at temperatures above 120°F (49°C).
- Vapor Harmful: Use only in a well-ventilated area. Avoid breathing vapors. If experiencing dizziness, headache, or nausea, move to fresh air.
- Keep Away From Children: Store in a location inaccessible to children.
- Electrical Shock Hazard: This material can conduct electricity. Failure to turn off power to electrical sources may result in electrical shock.
- Environmental Restrictions: Not VOC Compliant for California & OTC. This item is not for sale in Catalina Island.
Image 2.1: Detailed view of the product label, highlighting safety warnings and usage directions.
3. Preparation
- Ensure the engine is off and the belt is stationary before beginning any cleaning or application process.
- For personal safety, do not apply while equipment is in operation.
- Clean the belt surface: Ensure the belt is free from wax, grease, or other contaminants. A clean, dry surface is essential for optimal product adhesion and effectiveness.
4. Operating Instructions
Follow these steps for effective application of CRC 05350 Belt Conditioner:
- Shake the can well before use.
- Hold the can in an upright position, approximately 8-10 inches away from the belt surface.
- Apply the conditioner sparingly. Do not saturate the belt. A light, even coating is sufficient.
- Allow the product to penetrate and dry before operating the equipment.
Important Note: Some users report that initial application may temporarily increase belt noise before it subsides. This is often part of the conditioning process as the product works to clean and treat the belt surface. If noise persists, reapply sparingly.
5. Maintenance
For ongoing belt maintenance and to prevent drying out and slippage, apply CRC 05350 Belt Conditioner approximately every 3,000 miles or as needed based on belt condition and usage. Regular application helps to maintain the belt's flexibility and grip, extending its service life.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Belt squeaks persist after application | Insufficient application, temporary increase during conditioning, or underlying mechanical issue. | Reapply sparingly. If squeaking continues after multiple applications, inspect belt tension, alignment, and pulleys for wear or damage. |
| Belt slippage continues | Heavy contamination, worn belt, or incorrect belt tension. | Ensure belt surface is clean before application. Check belt for cracks or excessive wear. Verify and adjust belt tension according to equipment manufacturer specifications. |
| Product feels sticky on belt | Over-application. | Apply sparingly. The product is designed to provide grip, but excessive application can lead to stickiness. Allow time for the product to dry and integrate. |
7. Specifications
- Product Name: CRC Belt Conditioner
- Model Number: 05350
- Manufacturer: CRC
- Product Dimensions: 4.75 x 2.75 x 2.75 inches
- Net Weight: 7.5 Wt Oz (8 ounces total)
- ASIN: B000M8PZB4
- Date First Available: March 1, 2006
- UPC: 0078254053509
Image 7.1: Side view of the CRC 05350 Belt Conditioner can, showing the UPC code and other label details.
8. Warranty and Support
Information regarding specific warranty terms for the CRC 05350 Belt Conditioner is not provided in the available product details. For warranty inquiries or technical support, please refer to the official CRC Industries website or contact their customer service directly.
You can visit the official CRC store for more information: CRC Official Store