Kohler CB-CLC3026FS Bathroom Medicine Cabinet Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Kohler CB-CLC3026FS Bathroom Medicine Cabinet. This cabinet is designed with a sleek mirrored surface, beveled mirror doors, adjustable glass shelves, and durable aluminum construction, suitable for enhancing bathroom storage and aesthetics.

Figure 1: Kohler CB-CLC3026FS Medicine Cabinet (Closed)

2. Important Safety Information

WARNING:

• Do not overload shelves. Maximum weight capacity is 60 pounds.
• Be cautious of sharp edges if glass breaks.
• Ensure proper installation to prevent tipping.
• Always use appropriate safety gear when handling or installing the cabinet.
• Turn off electricity to the installation site before cutting into the wall if performing a recessed installation.
• Consult a professional if encountering drain/vent piping, if the wall is load-bearing, or if installing to an exterior wall.

3. Key Features

• Adjustable Tempered-Glass Shelves: Two shelves for flexible storage.
• Double Doors: Full-overlay beveled mirrors for a seamless look.
• Mirrored Interior: Provides enhanced visibility and aesthetics.
• Two-Way Adjustable Hinges: 108° opening capability for easy access.
• Side Mirror Kit: Included for surface-mount installation.
• Durable Construction: Anodized aluminum, rust-free and chip-free finish.
• Reversible: Can be installed for left or right-hand door opening.

Figure 2: Key Features Overview

4. Package Contents

Verify all components are present before beginning installation:

• Medicine Cabinet Unit with Mirror Doors
• 2 Adjustable Tempered Glass Shelves
• Mounting Hardware (screws, wall anchors, clips)
• Side Mirror Kit (for surface-mount installation)
• Installation Guide

5. Installation

The Kohler CB-CLC3026FS medicine cabinet can be installed as either a recessed (in-wall) or surface-mount unit. Refer to the specific instructions provided in your product's installation guide for detailed measurements and procedures.

5.1. Planning and Location

• Choose an installation location that allows at least 3 inches (76 mm) of clearance above and below the cabinet door for lighting and faucet clearance.
• Determine if you will perform a recessed or surface mount installation.
• Ensure the wall can support the weight of the cabinet (Item Weight: 36 Pounds, Maximum Weight Capacity: 600 Pounds).

5.2. Recessed (In-Wall) Installation

1. Mark Cutout: Using a pencil, mark the outline for the wall cutout based on the dimensions provided in your installation guide.
2. Locate Studs/Obstructions: Use a stud finder to locate any studs, electrical wiring, or plumbing within the marked cutout area. Mark their locations.
3. Assess Wall Cavity: Cut a small opening to assess the wall cavity for any obstructions. Any electrical wires or water supply piping will need to be rerouted.
4. Cut Drywall: Carefully cut the drywall along the marked lines.
5. Frame Opening: Remove any studs within the wall cavity. Measure and cut 2x3 lumber for header and footer pieces to frame the wall opening. Ensure the 2x3s do not extend beyond the cut edge of the drywall. Nail these pieces to each stud to hold them in place.
6. Secure Drywall: Secure the drywall to the framing with screws. Repair and paint the drywall as needed.
7. Insert Cabinet: With assistance (this step requires two people), insert the cabinet into the newly framed opening and hold in place. Check the cabinet for level.
8. Secure Cabinet: Open the cabinet doors and locate the four mounting holes. Secure the cabinet with the four screws provided.

5.3. Surface-Mount Installation

For surface-mount installation, use the included side mirror kit. The kit provides side mirrors that attach to the cabinet, covering the exposed sides when mounted directly to the wall surface. Follow the specific instructions in your product guide for attaching the side mirrors and securing the cabinet to the wall using the provided mounting hardware.

Figure 3: Medicine Cabinet with doors open, showing interior storage.

6. Operation

6.1. Adjustable Shelves

To adjust the glass shelves:

1. Open the cabinet doors.
2. Remove any items from the shelf you wish to adjust.
3. Firmly press the shelf clips into the desired holes on the side of the cabinet. Ensure clips on both sides align.
4. Position the shelf at an angle, with one end resting on the shelf clips.
5. Firmly press the other end of the shelf into place. The shelf fit is tight to ensure stability.
6. Plug any unused holes with the provided plugs for a clean appearance.

6.2. Door Operation

The cabinet features two-way adjustable hinges with 108° opening capability for easy access. The hinges allow for side-to-side, vertical, and front-to-back adjustment to ensure proper door alignment. Refer to your product's installation guide for detailed hinge adjustment instructions.

7. Care and Maintenance

• Clean mirrored surfaces with a soft, damp cloth and a mild glass cleaner. Avoid abrasive cleaners.
• For the aluminum frame, wipe with a soft, damp cloth. Do not use harsh chemicals or abrasive materials that could damage the finish.
• Regularly check hinge screws for tightness and adjust if necessary to maintain proper door function.

8. Troubleshooting

• Doors not aligning: Adjust the two-way hinges using a screwdriver. Refer to the installation guide for specific adjustment points.
• Shelves feel loose: Ensure shelf clips are fully inserted into the holes and that the shelf is firmly seated on all clips. The fit is designed to be tight.
• Cabinet appears wobbly: Re-check all mounting screws to ensure they are securely fastened to the wall studs or wall anchors.

9. Specifications

10. Warranty and Support

For warranty information, technical support, or to order replacement parts, please refer to the official Kohler website or contact Kohler customer service directly. Keep your purchase receipt for warranty claims.

Visit the KOHLER Store for more products and information.