Product Overview
The RACO 808C is a durable alloy steel work cover designed for use with 4-inch square electrical boxes. It provides a secure and raised mounting surface for a single GFCI (Ground Fault Circuit Interrupter) receptacle, ensuring proper fit and protection in exposed installations. This cover is 1/2 inch raised, accommodating the depth requirements of GFCI devices.
A silver-colored, square metal electrical box cover with a rectangular cutout in the center, designed to accommodate a single GFCI receptacle. It features rounded corners and screw holes for mounting.
Safety Information
WARNING: Risk of electric shock. Always turn off power at the circuit breaker or fuse box before installing, servicing, or removing any electrical components. Improper installation can result in serious injury or death.
- Ensure all local and national electrical codes are followed.
- If you are unsure about any part of the installation process, consult a qualified electrician.
- Do not install this product if the electrical box or wiring is damaged.
- Wear appropriate personal protective equipment, such as safety glasses and insulated gloves.
Setup and Installation
This section provides instructions for installing the RACO 808C GFCI Work Cover onto a 4-inch square electrical box.
Tools Required:
- Screwdriver (Phillips or flathead, depending on screw type)
- Voltage tester
- Wire strippers (if installing new GFCI receptacle)
Installation Steps:
- Turn Off Power: Locate the circuit breaker or fuse controlling the electrical box where the cover will be installed. Turn off the power completely. Verify with a voltage tester that the power is off before proceeding.
- Prepare the Electrical Box: Ensure the 4-inch square electrical box is properly secured and all wiring is ready for connection to the GFCI receptacle.
- Position the Work Cover: Place the RACO 808C work cover over the opening of the 4-inch square electrical box, aligning the screw holes on the cover with those on the box.
- Secure the Work Cover: Insert the appropriate mounting screws (typically provided with the electrical box or cover) through the cover's screw holes and into the electrical box. Tighten the screws firmly but do not overtighten, which could strip the threads or deform the cover.
- Install GFCI Receptacle: Connect the GFCI receptacle according to its manufacturer's instructions. Once wired, carefully insert the GFCI receptacle into the rectangular opening of the RACO 808C cover. The raised design of the cover provides the necessary space.
- Secure GFCI Receptacle: Use the screws provided with the GFCI receptacle to secure it to the work cover. Ensure the GFCI is flush and stable.
- Restore Power: Once the GFCI receptacle is fully installed and secured, return to the circuit breaker or fuse box and restore power. Test the GFCI receptacle according to its instructions.
Operation
Once properly installed, the RACO 808C GFCI Work Cover functions as a protective and mounting interface for your GFCI receptacle. It provides a secure, raised surface, ensuring the GFCI device is correctly positioned and protected within the electrical system.
Maintenance
The RACO 808C GFCI Work Cover requires minimal maintenance to ensure continued performance and appearance.
- Cleaning: Periodically wipe the cover with a soft, damp cloth to remove dust and dirt. Avoid abrasive cleaners or solvents, which can damage the finish.
- Inspection: Annually inspect the cover for any signs of damage, corrosion, or loose screws. Ensure it remains securely fastened to the electrical box and that the GFCI receptacle is firmly in place.
- Damage: If the cover becomes bent, cracked, or severely corroded, it should be replaced immediately to maintain safety and integrity.
Troubleshooting
Most issues related to the RACO 808C work cover are installation-related or due to physical damage.
- Cover Does Not Fit: Ensure you are using a standard 4-inch square electrical box. This cover is specifically designed for that size. Verify the GFCI receptacle is a standard size for single-gang openings.
- Screws Do Not Tighten: Check if the screw holes on the electrical box are stripped. If so, the box may need repair or replacement. Do not overtighten screws.
- GFCI Receptacle Not Flush: Ensure all wiring is neatly tucked into the electrical box and not obstructing the GFCI or cover. The 1/2 inch raised design should provide adequate depth for most standard GFCIs.
- Visible Damage: If the cover is bent, cracked, or shows signs of severe corrosion, replace it. Physical damage can compromise its protective function.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 808C |
| Brand | RACO |
| Manufacturer | HUBBELL |
| Material | Alloy Steel |
| Color | Silver |
| Style | Compact |
| Finish Type | Polished |
| Compatibility | 4-inch Square Electrical Box, Single GFCI Receptacle |
| Raised Depth | 1/2 inch |
| Package Dimensions | 4.06 x 4.06 x 0.55 inches |
| Item Weight | Approximately 0.01 ounces |
Warranty and Support
For specific warranty information, please refer to the documentation provided with your purchase or contact RACO customer support directly. RACO products are manufactured to high standards, and support is available for product-related inquiries.
RACO Customer Support: Please visit the official RACO website or contact your retailer for support options.
