Introduction
The Digi-Code Wireless Fully-Programmable Keypad provides convenient keyless access to your garage door or gate opener. Designed for outdoor use, its flip lid protects the keypad from environmental elements. This wireless unit is powered by a 9-volt alkaline battery and is compatible with various Stanley operators and 310MHz Digi-Code Receivers. It supports 1024 dip switch codes and allows users to set and change their personal identification number (P.I.N.).
Product Overview
Image: Front view of the Digi-Code Wireless Fully-Programmable Keypad. The keypad features a light-colored casing with a dark grey numerical button pad. A flip lid is visible at the top, designed to protect the buttons from weather. The Digi-Code logo is visible below the lid. The unit is rectangular with rounded edges.
Setup and Installation
1. Battery Installation
The keypad requires a 9-volt alkaline battery for operation. To install the battery:
- Locate the battery compartment, typically on the back or bottom of the unit.
- Open the compartment cover.
- Insert a new 9-volt alkaline battery, ensuring correct polarity.
- Close the battery compartment cover securely.
2. Mounting the Keypad
The keypad is designed for outdoor mounting near your garage door or gate. Choose a location that is easily accessible but protected from direct impact. Use appropriate screws and anchors for your mounting surface.
- Mark the desired mounting holes on the surface.
- Drill pilot holes if necessary.
- Secure the keypad using suitable fasteners.
Operating Instructions
1. Setting Dip Switches (for compatible openers)
For garage door openers that use dip switches, you must match the keypad's dip switch settings to those of your opener. The Digi-Code DC5202 supports 1024 dip switch codes.
- Locate the dip switches inside the keypad (usually behind the battery compartment or a separate cover).
- Refer to your garage door opener's manual to find its dip switch settings.
- Adjust the switches on the keypad to match the "ON" or "OFF" positions of your opener's switches.
2. Programming Your P.I.N. (Personal Identification Number)
Your P.I.N. is a user-changeable code that grants access. Follow these steps to set or change your P.I.N.:
- Open the keypad's flip lid.
- Press the PROGRAM button (location may vary, refer to internal diagram if available).
- Enter your desired P.I.N. (typically 4-6 digits).
- Press the PROGRAM button again to save.
- Test your new P.I.N. by entering it and pressing the ENTER button.
3. Opening/Closing the Door
To operate your garage door or gate:
- Enter your programmed P.I.N.
- Press the ENTER button.
- The door/gate should activate.
Maintenance
Battery Replacement
The keypad is powered by a 9-volt alkaline battery. Battery life will vary depending on usage and environmental conditions. Replace the battery when the keypad's backlight dims or if the unit becomes unresponsive.
- Open the battery compartment.
- Remove the old 9-volt battery.
- Insert a new 9-volt alkaline battery, observing polarity.
- Close the compartment securely.
Cleaning
Clean the keypad's exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or electronic components. Ensure the flip lid is kept clean and free of debris to ensure proper closure and protection.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Keypad does not respond or backlight is dim. | Low or dead battery. | Replace the 9-volt alkaline battery. |
| Keypad enters code but door/gate does not activate. | Incorrect dip switch settings or P.I.N. not programmed correctly. Incompatible frequency. |
|
| Keypad buttons are sticky or hard to press. | Dirt or debris under buttons. | Clean the keypad surface and around buttons with a soft, damp cloth. |
Specifications
- Manufacturer: DIGI-CODE
- Part Number: DC5202
- Model Number: CECOMINOD038261
- Item Weight: 7.2 ounces
- Package Dimensions: 6.8 x 3.3 x 1.1 inches
- Style: Wall Mount
- Power Source: 9-volt alkaline battery (not included)
- Special Features: Backlit keypad, Flip lid design
- Compatibility: ALL 10 Dip Switch Stanley operators, 310MHz Digi-Code Receivers
- Code Capacity: 1024 dip switch codes, User-changeable P.I.N.
Warranty and Support
For specific warranty information regarding your Digi-Code Wireless Fully-Programmable Keypad, please refer to the documentation included with your purchase or contact Digi-Code customer support directly.
If you require technical assistance or have questions not covered in this manual, please visit the official Digi-Code website or contact their customer service department. Contact information can typically be found on the manufacturer's packaging or website.