Introduction
This manual provides essential information for the installation, maintenance, and general understanding of the Moen 115061 Replacement Split Bearing Washer Kit. This kit is designed as a genuine Moen replacement part for specific kitchen faucets, ensuring proper function and longevity.
The Moen 115061 kit includes a split bearing and O-ring, crucial components for maintaining the smooth operation and preventing leaks in your Moen kitchen faucet. Please read all instructions carefully before proceeding with installation.
Safety Information
Always prioritize safety when working with plumbing. Follow these guidelines:
- Turn off the main water supply to the faucet before beginning any work.
- Ensure the work area is well-lit and clear of obstructions.
- Wear appropriate personal protective equipment, such as safety glasses and gloves.
- If you are unsure about any step, consult a qualified plumber.
- Keep small parts away from children.
Package Contents
Verify that all components are present in your Moen 115061 Replacement Split Bearing Washer Kit:
- 1 x Split Bearing Washer (approximately 2 inches in diameter)
- 1 x O-ring
Image: The Moen 115061 kit, showing the split bearing washer, O-ring, and sealed packaging.
Setup and Installation
This kit is typically used to repair leaks or restore smooth operation to the spout of compatible Moen kitchen faucets. The exact installation steps may vary slightly depending on your specific faucet model. Refer to your faucet's original manual for detailed disassembly instructions if needed.
General Installation Steps:
- Prepare the Faucet: Turn off the water supply to the faucet (both hot and cold lines). Open the faucet handles to relieve any remaining water pressure. Place a towel or bucket under the faucet to catch any drips.
- Disassemble the Faucet Spout: Carefully remove the faucet handle(s) and any decorative caps or escutcheons. Locate the retaining nut or screw that secures the spout. Loosen and remove it. Gently lift and remove the spout from the faucet body.
- Remove Old Components: Inspect the base of the faucet body where the spout was seated. You will likely find the old split bearing washer and O-ring. Carefully remove these worn components. Clean the area thoroughly, removing any mineral deposits or debris.
- Install New Components: Place the new O-ring into its groove on the faucet body or the base of the spout, depending on your faucet design. Then, position the new split bearing washer. Ensure it sits correctly and is not twisted. A small amount of plumber's grease (compatible lubricant) can be applied to the O-ring to aid in installation and provide a better seal.
- Reassemble the Faucet: Carefully place the spout back onto the faucet body, aligning it with the new washer and O-ring. Secure the spout with its retaining nut or screw. Reattach the handle(s) and any decorative components.
- Test for Leaks: Slowly turn the water supply back on. Check for any leaks around the base of the spout. Operate the faucet handles to ensure smooth movement and proper water flow.
If you encounter resistance or difficulty during reassembly, double-check the alignment of the components and ensure no parts are pinched.
Operating (Function)
The Moen 115061 Replacement Split Bearing Washer Kit is a functional component designed to restore the proper operation of your Moen kitchen faucet spout. Once correctly installed, it ensures:
- Smooth Spout Swivel: The split bearing allows the faucet spout to rotate smoothly without excessive friction or stiffness.
- Leak Prevention: The O-ring, in conjunction with the bearing, creates a watertight seal at the base of the spout, preventing water from leaking out when the faucet is in use.
- Restored Performance: Replacing worn components with this genuine Moen kit helps restore your faucet to its original performance standards.
Maintenance
Once installed, the Moen 115061 kit requires minimal ongoing maintenance. However, periodic checks can help prolong the life of your faucet components:
- Regular Cleaning: Keep the exterior of your faucet clean to prevent mineral buildup around the spout base. Use a soft cloth and mild soap; avoid abrasive cleaners.
- Leak Detection: Periodically check for any signs of water leakage around the spout base. Early detection can prevent further damage.
- Spout Movement: If the spout begins to feel stiff or difficult to swivel, it may indicate a need for lubrication or eventual replacement of the bearing and O-ring.
Troubleshooting
If you experience issues after installing the Moen 115061 kit, consider the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leaking from spout base after installation. |
|
|
| Spout is stiff or difficult to swivel. |
|
|
If problems persist, contact Moen customer support or a professional plumber.
Specifications
| Attribute | Detail |
|---|---|
| Brand | Moen |
| Model Number | 115061 |
| Part Type | Replacement Split Bearing Washer Kit |
| Material | Rubber |
| Bearing Type | Split |
| Outside Diameter | 2 Inches (approximate for washer) |
| Item Thickness | 1 Inches (approximate for washer) |
| Compatible Lubricant | Grease (Plumber's Grease recommended) |
| Item Weight | Approximately 0.03 Pounds / 0.48 ounces |
| Dimensions (L x W x H) | 2.6 x 2 x 0.4 inches (packaging/overall) |
| UPC | 026508114445 |
Warranty and Support
The Moen 115061 Replacement Split Bearing Washer Kit is backed by Moen's One-Year Limited Warranty. This warranty covers defects in material and manufacturing for a period of one year from the date of purchase.
For warranty claims, technical assistance, or further product information, please contact Moen customer support directly. Ensure you have your product model number (115061) and proof of purchase available when contacting support.
Moen Customer Support:
- Refer to the official Moen website for current contact information (phone numbers, email, or online support forms).
- Visit www.moen.com for product registration, FAQs, and support resources.
