Introduction
Thank you for purchasing the Trans Globe Lighting Wentworth Collection Outdoor Wall Lantern. This manual provides essential information for the safe installation, operation, and maintenance of your new light fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.
Figure 1: Front view of the Trans Globe Lighting Wentworth Collection Outdoor Wall Lantern. This image shows the black finish, clear beveled glass panels, and the decorative scroll arm.
Safety Information
WARNING: Risk of electric shock. Disconnect power at the fuse box or circuit breaker before installation or servicing. All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). If you are unfamiliar with electrical wiring, consult a qualified electrician.
- Ensure the fixture is properly grounded.
- Do not exceed the maximum wattage specified for the bulb.
- This fixture is UL Approved for WET Locations, making it suitable for outdoor use where it may be exposed to rain or moisture.
- Wear safety glasses during installation.
Setup and Installation
Package Contents
- 1 x Outdoor Wall Lantern Fixture
- Mounting Hardware (screws, wire nuts, mounting plate)
Tools Required (Not Included)
- Phillips head screwdriver
- Flathead screwdriver
- Wire strippers
- Electrical tape
- Ladder (if installing at height)
- Safety glasses
Installation Steps
- Turn off power: Locate the circuit breaker or fuse box that supplies power to the light fixture location and turn off the power. Verify power is off using a voltage tester.
- Prepare mounting surface: Ensure the mounting surface is clean, dry, and structurally sound.
- Attach mounting plate: Secure the mounting plate to the junction box using the provided screws. Ensure the plate is level.
- Make electrical connections:
- Connect the fixture's black wire to the house's black (hot) wire.
- Connect the fixture's white wire to the house's white (neutral) wire.
- Connect the fixture's ground wire to the house's ground wire (or ground screw on the mounting plate).
- Secure all connections with wire nuts and electrical tape.
- Mount the fixture: Carefully align the fixture with the mounting plate and secure it with the provided screws.
- Install bulb: Insert one A19 shape incandescent bulb (not included) into the E26 medium base socket. Do not exceed 60 watts.
- Restore power: Turn the power back on at the circuit breaker or fuse box.
Figure 2: View of the internal mounting bracket and wiring connections. This shows how the fixture attaches to the electrical box.
Figure 3: The outdoor wall lantern with a bulb installed, ready for operation.
Operating Instructions
Once installed, the Trans Globe Lighting Wentworth Collection Outdoor Wall Lantern operates like any standard outdoor light fixture. It is designed for use with a wall switch or a compatible outdoor lighting control system.
- Turning On/Off: Use the connected wall switch to turn the light fixture on or off.
- Dimmable Feature: This fixture is dimmable. If connected to a compatible dimmer switch (sold separately), you can adjust the brightness of the light. Ensure the bulb used is also dimmable.
Figure 4: The light fixture elegantly installed on an exterior stone wall, demonstrating its outdoor application.
Maintenance
Regular maintenance will ensure the longevity and optimal performance of your outdoor wall lantern.
- Cleaning: To clean the fixture, turn off the power and wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents, as they may damage the finish or glass.
- Bulb Replacement:
- Turn off power at the circuit breaker.
- Allow the old bulb to cool completely before removing it.
- Unscrew the old bulb and screw in a new A19 shape incandescent bulb (max 60 watts) with an E26 medium base.
- Restore power.
- Periodic Inspection: Periodically check the fixture for any signs of wear, loose connections, or damage. Address any issues promptly.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. Loose wiring connection. Faulty bulb. | Check circuit breaker/fuse. Turn off power and check all wire connections. Replace bulb. |
| Light flickers. | Loose bulb. Loose wiring connection. Incompatible dimmer switch/bulb. | Tighten bulb. Turn off power and check all wire connections. Ensure both bulb and dimmer are compatible. |
| Glass panels are dirty. | Exposure to outdoor elements. | Clean with a soft, damp cloth. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | 4181 BK |
| Dimensions (H x W x D) | 16 x 7.5 x 8 inches |
| Item Weight | 3.31 Pounds |
| Material | Metal, Glass, Electrical |
| Finish | Black |
| Light Source Type | Medium Base (E26) |
| Maximum Wattage | 60 Watts |
| Voltage | 120 Volts |
| Indoor/Outdoor Usage | Outdoor |
| Water Resistance Level | Waterproof |
| Special Feature | Dimmable |
| Included Components | Mounting Hardware |
Warranty
This Trans Globe Lighting product is covered by a One Year Limited Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, misuse, abuse, or acts of nature. For warranty claims, please retain your proof of purchase and contact the manufacturer.
Support
For further assistance or technical support, please refer to the official Trans Globe Lighting website or contact their customer service department. Always provide your product model number (4181 BK) when seeking support.
You can also refer to the official user guide PDF available online: Trans Globe Lighting 4181 BK User Guide (PDF)