1. Introduction
Thank you for choosing the Taylor Made 80240 Small Swingback Boat Seat Cover. This cover is engineered to provide robust protection for your boat's swingback seats against various environmental elements, including sun, rain, and abrasion. By following the instructions in this manual, you can ensure optimal performance and extend the lifespan of your boat seating upholstery.
2. Product Overview
The Taylor Made 80240 Boat Seat Cover is constructed from durable, UV-resistant rip-stop polyester fabric. This material is specifically chosen for its ability to withstand harsh marine conditions, offering superior protection against UV degradation, water penetration, and general wear and tear. The design ensures a secure fit, helping to keep your boat seats clean and well-preserved.
Figure 2.1: The Taylor Made 80240 Small Swingback Boat Seat Cover. This image shows the navy blue cover designed to fit over a boat's swingback seat, providing protection from the elements.
3. Setup and Installation
- Prepare the Seat: Ensure the boat seat is clean and dry before applying the cover. Remove any loose debris or moisture.
- Unfold the Cover: Carefully unfold the Taylor Made 80240 cover, identifying the front and back sections.
- Position the Cover: Drape the cover over the swingback boat seat. Start by aligning the top edge of the cover with the top of the seat back.
- Adjust for Fit: Pull the cover down over the seat cushion and backrest, ensuring it snugly fits the contours of the seat. The cover is designed for a secure fit, but minor adjustments may be needed to achieve optimal coverage.
- Secure the Cover: Locate the integrated draw rope or elastic hem at the bottom edge of the cover. Tighten this mechanism to secure the cover firmly around the base of the seat, preventing it from being dislodged by wind or movement.
- Check Coverage: Verify that all exposed areas of the seat upholstery are adequately covered and protected.
Note: While the cover is designed for a universal fit on small swingback seats, slight variations in seat dimensions may result in minor differences in coverage, particularly in height. Ensure the primary seating surfaces are protected.
4. Operating Instructions
The Taylor Made 80240 Boat Seat Cover is designed for straightforward use:
- Applying the Cover: Follow the setup instructions above whenever you need to protect your boat seat from the elements, such as when docking, storing, or during periods of non-use.
- Removing the Cover: To remove, simply loosen the draw rope or elastic hem and lift the cover off the seat. Fold it neatly for storage to prevent creases and damage.
- Weather Protection: The cover provides effective protection against UV rays, rain, wind, and mildew. It is recommended to use the cover consistently to maximize the lifespan of your boat's upholstery.
5. Care and Maintenance
Proper care and maintenance will ensure the longevity and effectiveness of your boat seat cover:
- Cleaning: Clean the cover periodically with mild soap and water. Use a soft brush or sponge to gently scrub away dirt and grime. Rinse thoroughly with fresh water and allow it to air dry completely before folding or storing. Do not use harsh chemicals or abrasive cleaners, as these can damage the fabric and its UV protective coating.
- Drying: Always ensure the cover is completely dry before storing to prevent mildew growth.
- Storage: When not in use, store the cover in a cool, dry place, away from direct sunlight and extreme temperatures. Folding it neatly will help prevent unnecessary creasing.
- Inspection: Regularly inspect the cover for any signs of wear, tears, or damage. Promptly address minor issues to prevent them from worsening.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Cover does not fit snugly. | Improper positioning or insufficient tightening of the draw rope/elastic. | Re-position the cover, ensuring it is centered and fully draped. Tighten the draw rope or elastic hem securely. Verify the seat dimensions are compatible with a "small swingback" cover. |
| Water pooling on the cover. | Lack of proper tension or an uneven surface underneath. | Ensure the cover is pulled taut and secured. If possible, create a slight peak or incline to allow water to run off. |
| Mildew growth. | Cover stored wet or in a damp environment. | Clean the mildewed area with a mild bleach solution (diluted) or specialized mildew remover, then rinse thoroughly and dry completely. Always ensure the cover is dry before storage. |
| Cover appears damaged or torn. | Abrasion from sharp objects or prolonged exposure to extreme conditions. | Inspect the boat seat and surrounding area for any sharp edges. Small tears may be repairable with marine-grade fabric repair kits. For significant damage, consider replacement. |
7. Product Specifications
- Model Number: 80240
- Brand: TaylorMade
- Material: Rip-Stop Polyester Fabric
- Color: Navy (as per product description)
- Protection Features: UV Protection, Water Resistant, Wind Resistant, Mildew Resistant
- Fit Type: Universal Fit (for small swingback boat seats)
- GTIN/UPC: 040011090294
Note: Dimensions (14 x 10 x 4 inches) listed in some product specifications refer to the packaged item and not the cover's functional dimensions. The cover is designed to fit small swingback boat seats.
8. Warranty and Customer Support
Taylor Made Products provides a warranty for this product. For specific details regarding the warranty period, coverage, and claims process, please refer to the warranty information included with your purchase or visit the official Taylor Made Products website. Keep your proof of purchase for warranty purposes.
For technical assistance, product inquiries, or to report any issues, please contact Taylor Made Products customer support. Contact information can typically be found on the manufacturer's website or product packaging.