arboleaf CS10E Body Composition Smart Scale
Product Description
Product Front Demonstration
Product Back Demonstration
Product Specifications
Screen Display
Battery Installation
Remove the rear battery isolation tab to activate the power device. 
When the scale displays ‘Lo’, it indicates low battery and requires timely replacement of batteries (3XL.SV AM).
Initial Setup
Step 1: Download the “arboleaf” app and create an account. From Apple App Store (iOS) or Google Play (Android), search for “arboleaf” and download it to your smartphone. You can also scan the QR code to download.
- Download the “arboleaf” app or scan the QR code
- Register an account
Step 2: Pair the scale with your smartphone.
Make sure Bluetooth is enabled on your phone. For Android 6.0 and above, Location also needs to be enabled. Pairing is done automatically. The Bluetooth icon is displayed on the scale.
- Open the “arboleaf” app
- Apply pressure to turn on the scale
Take Measurements
- Connecting to the Scale Using the App
- To use the scale for the first time, you need to connect it to the app via Bluetooth (refer to Initial setup). Otherwise, only weight measurements will be displayed. Subsequent uses will allow direct measurement without needing to reconnect.
- Stepping onto the Body Fat Scale
- Please step onto the body fat scale barefoot. Stand upright on the scale and firmly grip the handle with both hands. Wait for the weight to stabilize; a blinking weight indicates the measurement is complete.
- Please step onto the body fat scale barefoot. Stand upright on the scale and firmly grip the handle with both hands. Wait for the weight to stabilize; a blinking weight indicates the measurement is complete.
After confirming the weight, proceed to measure body fat percentage and other body composition metrics
Ensure that arms are positioned away from the sides of the body, with the inner thighs not in contact, maintaining an upright stance with arms raised until the measurement is complete.
Body Fat Scale Measurement Demonstration Body Illustration
- Stand upright with arms naturally hanging down at an angle from the body, ensuring arms do not touch the waist.
- Avoid bending the hands outward.
- The hands are horizontally for measurement.
- Avoid bending the hands during measurement.
- Wear form-fitting clothing only during the measurement process.
Body Fat Scale Measurement Demonstration – Foot Placement Illustration
Stand with feet parallel on the scale electrodes, ensuring inner thighs do not touch each other.
- The heels of both feet should not touch each other.
- The feet should not be placed in a heel-to-heel stance.
Body Fat Scale Measurement Demonstration -Hand Demonstration Image
Thumb touching the oval electrode, four fingers touching the elongated electrode, with the handle connector wire facing downwards.
- Hands should not be clenched.
- The handle connector wire should not face upwards.
Displaying Measurement Results
The scale displays weight, body fat, body water, muscle mass, bone mass, visceral fat, BMI, and rotation (switching between weight and BMI data, each displayed for 3 seconds). For additional metrics, please refer to the app after measurement.
Display Screen Icon Guide
 | Bluetooth icon: Illuminates when Bluetooth is enabled. |
 | Body fat percentage icon: Illuminates when disp laying body fat percentage measurement results. |
 | Body water icon: Illuminates when displaying body water measurement results. |
 | Muscle icon: Illuminates when displaying muscle mass measurement results. |
 | Bone mass icon: Illuminates when displaying bone mass measurement results. |
 | Visceral fat level icon: Illuminates when displaying visceral fat level measurement results. |
 | BMI icon: Illuminates when displaying BMI measurement results. |
| % | Percentage unit |
 | Low battery |
 | Upward arrow illuminated: Indicates the measurement value is higher than the previous measurement. |
 | Downward arrow illuminated: Indicates the measurement value is lower than the previous measurement. |
 | Overload |
 | Weight instability warning |
 | Weight detected after stepping off |
 | Please return the handle to the scale when this icon is scrolling. |
CAUTION
- Do not use with implanted medical electronic devices such as pacemakers, artificial hearts, or life-supporting medical electronic devices, or wearable medical electronic devices like electrocardiographs.
- Individuals with limb defects cannot use (measurement requires good contact with all eight electrode pads).
- Do not jump on the scale.
- It is recommended to measure at the same time each day under the same conditions.
- For accurate measurement, place the scale on a hard, flat surface.
WARNING
Please read carefully before use
- Do not use if you have a pacemaker or any other internal medical devices in your body.
- Do not use if you are pregnant.
- Do not use on slippery floors.
- Do not use when your body is wet.
- Do not use rechargeable 1.2V AAA batteries.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that maycause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC ID: 2AN DX-CSX00
WARRANTY
- Arboleaf Corporation warrants this product purchased from an authorized seller to be free from defects in workmanship and materials, under normal use and conditions, for a period of one year following the date of purchase.
- Proof of purchase is required.
- This warranty does not cover failures due to misuse, abuse. accidental damage or unauthorized repair.
CONTACT
ARBOLEAF CORPORATION
- HM REVENUE AND CUSTOMS
- RUBY HOUSE
- 8 RUBY PLACE, ABERDEEN, ABIO IZP GB 450744596
- Manufactured by Shenzhen Yolanda Technology Co., Ltd.
- Address: Room 201, Jinfulai Building, No.49-l, Dabao Road, Dalang Area,
- Xinan Street, Baoan, Shenzhen,China
- service@yolanda.hk
- Custom Support Service (EU)
- support.eu@arboleaf.com
- Custom Service (US)
- Arboleaf Corporation
- 5465 Legacy Drive, Suite 650, Plano, TX 75024, USA
- 1-800-658-1148
- support@arboleaf.com
- www-arboleaf.com
Company: YH Consulting Limited- Address: C/O YH Consulting Limited, Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX
- E-mail: H2YHUK@gmail.com
- +44 07514-677868
E – CrossStu – GmbH- Mainzer Landstr. 69
- 60329 Frankfurt am Main
- Mail: E-CrossStu@web.de
Documents / Resources
 | arboleaf CS10E Body Composition Smart Scale [pdf] User Guide CS10E, CS10E Body Composition Smart Scale, Body Composition Smart Scale, Composition Smart Scale, Smart Scale |