مقدمة
The E-flite EFLA600 Universal Light Kit Controller is designed to provide remote control functionality for LED lighting systems on remote-controlled aircraft. This controller enables users to activate and deactivate connected LED lights via an auxiliary channel on their RC receiver, enhancing visibility and realism for various RC models.
احتياطات السلامة
- Always disconnect power from your RC system before making any electrical connections or disconnections to prevent damage to components or injury.
- تأكد من أن مستوى الصوت المدخلtage to the controller does not exceed 5.5 فولت. Exceeding this voltagسيؤدي ذلك إلى إتلاف وحدة التحكم.
- Verify correct polarity when connecting LED lights to the controller outputs. Incorrect polarity can damage the LEDs or the controller.
- Keep the controller and all electrical components away from moisture and extreme temperatures.
- This product is intended for use with E-flite Universal Light Kit LEDs. Compatibility with other LED types is not guaranteed.
الإعداد والتثبيت
Follow these steps to properly install and connect your E-flite EFLA600 Universal Light Kit Controller:
- الاتصال بجهاز الاستقبال: Plug the controller's servo lead (the three-wire connector) into an available auxiliary channel on your RC receiver. This channel will be used to control the ON/OFF function of the lights.
- توصيل مصابيح LED: Connect your E-flite Universal Light Kit LEDs to the white JST-style output ports on the controller. The controller supports up to 16 individual LEDs. Ensure each LED string is securely connected.
- مصدر الطاقة: The controller draws power directly from the receiver. Ensure your receiver's power supply (e.g., BEC from an ESC or a separate receiver battery) can provide sufficient current for the controller and all connected LEDs.
This image shows the E-flite EFLA600 Universal Light Kit Controller. It is a small, black rectangular unit with the E-flite logo and product information printed on it. Wires extend from both ends: one end has a standard servo connector for receiver input, and the other end has four white JST-style connectors for attaching LED light strings.
تعليمات التشغيل
The E-flite EFLA600 controller operates by interpreting the pulse width signal from your receiver's auxiliary channel.
- ON Function: The LED lights will turn ON when the pulse width from the receiver channel is greater than 1.5 milliseconds (> 1.5ms).
- وظيفة إيقاف التشغيل: The LED lights will turn عن when the pulse width from the receiver channel is less than 1.5 milliseconds (< 1.5ms). This typically corresponds to approximately the middle stick position on your transmitter for a two-position switch or a specific range for a proportional channel.
Average Current Load
The current draw depends on the number of connected LEDs:
- 6 المصابيح: Approximately 60mA @ 5.5 volts
- 12 المصابيح: Approximately 120mA @ 5.5 volts
- 16 المصابيح: Approximately 160mA @ 5.5 volts
Ensure your receiver's power source can adequately supply this current without voltage drops, especially when operating other servos or components.
صيانة
The E-flite EFLA600 Universal Light Kit Controller requires minimal maintenance to ensure long-term performance:
- تنظيف: Keep the controller free from dust, dirt, and debris. Use a soft, dry cloth to gently wipe the unit if necessary. Avoid using solvents or harsh chemicals.
- تقتيش: Periodically inspect all wiring and connectors for signs of wear, damage, or corrosion. Ensure all connections are secure.
- تخزين: When not in use, store the controller in a cool, dry environment, away from direct sunlight and extreme temperatures.
استكشاف الأخطاء وإصلاحها
If you encounter issues with your E-flite EFLA600 controller, refer to the following troubleshooting guide:
| مشكلة | السبب المحتمل | حل |
|---|---|---|
| Lights do not turn ON/OFF | Incorrect receiver channel connection or assignment. Transmitter switch/stick position incorrect. Controller damaged. | Verify the servo lead is connected to an active auxiliary channel. Check transmitter settings for the assigned channel. Ensure the switch/stick moves past the 1.5ms threshold. |
| الأضواء تومض أو تكون خافتة | Loose connections. Insufficient power from receiver. Damaged LEDs. | Check all LED and receiver connections for security. Ensure receiver power supply can handle the current load. Test LEDs individually if possible. |
| وحدة التحكم لا تستجيب | حجم الإدخالtage out of range. Controller damaged. | التحقق من حجم الإدخالtage is between 3V and 5.5V. If voltage is correct and connections are secure, the controller may be damaged and require replacement. |
| فقط بعض مصابيح LED تضيء | Faulty LED string. Loose connection to a specific LED port. | Check connections for the non-working LEDs. Test individual LED strings if possible to identify faulty units. |
تحديد
| ميزة | مواصفة |
|---|---|
| رقم الموديل | EFLA600 |
| حجم الإدخالtage | 3 – 5.5 Volts DC (Do not exceed 5.5V) |
| Max LED Capacity | Up to 16 E-flite Universal Light Kit LEDs |
| تشغيل / إيقاف التحكم | Via RC receiver auxiliary channel |
| Activation Threshold | ON at > 1.5ms pulse width, OFF at < 1.5ms pulse width |
| Average Current Load (6 LEDs) | 60mA @ 5.5V |
| Average Current Load (12 LEDs) | 120mA @ 5.5V |
| Average Current Load (16 LEDs) | 160mA @ 5.5V |
| نوع المادة | بلاستيك |
| وزن العنصر | 0.02 رطل (حوالي 9 جرامًا) |
| أبعاد العنصر | 4 × 2.4 × 0.27 بوصة (حوالي 10.16 × 6.1 × 0.69 سم) |
| بلد المنشأ | الصين |
معلومات الضمان
For detailed warranty information regarding your E-flite EFLA600 Universal Light Kit Controller, please refer to the warranty documentation provided with your purchase or visit the official E-flite webقد تختلف شروط وأحكام الضمان حسب المنطقة والتاجر.
يدعم
If you require further assistance or have questions not covered in this manual, please contact E-flite customer support or visit their official webموقع إلكتروني يحتوي على موارد إضافية، وأسئلة شائعة، ومعلومات الاتصال.
شركة إي فلايت الرسمية Webموقع: www.e-fliterc.com