AOPEN Projectors
Precautions
How to use the device properly:
- Do not turn the lens toward human eyes when in operation, to avoid damaging the eyes caused by the high intensity light source.
- Do not block the device ventilation to avoid damage to the internal electronic devices due to overheating.
- Do not use chemicals, cleaning agents or clean water to clean the device, and prevent rain water, moisture and mineral-containing liquids from corroding circuit boards.
- Please keep the device and its parts and accessories out of reach of children.
- Please ensure that the device is operated in a dry and ventilated environment.
- Do not store the device in extreme hot or cold conditions. High and low temperatures may shorten the lifespan of electronic devices. The normal operating environment is between 5’C-30’C.
- Do not put the device into any drying equipment (such as dryer, microwave oven, etc.).
- Do not squeeze or place heavy objects over the device to avoid damage to the device.
- Do not throw, knock, or shake the device violently, which may damage the Internal circuit boards.
- Do not attempt to disassemble the device without permission. If there is any problem, please contact customer support.
- Do not repair any product by yourself. If the device or any part does not work properly, you should consult customer support or return the device for repair.
As the device Is a high Intensity light source, do not stare or look directly at the lens during operation, which may damage your eyes. This warning applies to children as well.
About Your Projector
About Your Remote Controller
Operating Instructions
Preparation at 1sttime usage
- Insert Acer Wireless Projection-Kit (UWA5 Wi-Fi dongle) into the WIRELESS KIT port on projector.
(Remark: The Wi-Fi dongle cannot be removed after plugging-in) - Plug the power adaptor in your projector depending on landscape mode or portrait mode. Charge your projector by 3 hours at 1st time usage.
- To turn on projector, long press the power button of the projector for 3 seconds or press power key on remote controller directly.
- Adjust focus ring until the projection image is clear and focused.
- Select your preferred start-up language.
- Use remote control to set up Wi-Fi connection.
- After starting up, enter the below home menu and select the functions by arrow keys on the projector or remote control: Android, iOS, MacOS, Windows, Bluetooth, EZCast, Media, HDMI, and Setting.
- To turn off projector, long press the power button of the projector for 3 seconds or press power key on remote controller directly.
About “Setting”
Use your remote controller to select “Setting” on home menu of projector, and press “ENTER” to confirm.
- Wi-Fi setting: elect the “Wi-Fi setting” menu and enter the Wi-Fi setting interface, select the “Internet”, press “ENTER” key to confirm, and select the router from AP list and enter the password.
- language menu: press the left and right arrow keys to select and switch the language.
- Firmware upgrade menu: you could upgrade firmware via Internet or USB drive. To upgrade via Internet, make sure projector Is connected to your Wi-Fi router first; to upgrade via USB drive, please download latest firmware from Acer official website and rename it as “ACTUPGRADE” before starting your firmware upgrade.
- Color setting: It offers the basic color setting for your color preference fine-tuned.
- Reset all: The projector will be restored to the factory settings, and the data adjusted by the user will not be saved.
About “Media”
Use your remote controller to select “‘Media” on home menu of projector, and press “ENTER” to confirm.
- Insert a USB flash drive Into USB port on the projector.
- Select the “Media” >> ”Video”, “Music” or “Photo” to enter the file folder.
- Select the file to play with the up and down arrow keys, and press “ENTER” to confirm.
- When playing media, press ENTER” to see the menu, and select item by the left and right keys.
- Supported format:
How to user your projector as power bank to charge your mobile (1) Under batteiy mode (without power adaptor), short press (<1s) the power button to tum on or turn off the power bank to supply 5V/0.5A (via Type A)
(2) With adaptor, USB power is always available without pressing any buttons. (3) Be noted that power charge is fered via Type A only.
Other Important notice:
Battery life varies depending on product settings, usage, and other factors.
How to Connect Your Device to play music via Bluetooth
About Auto Portrait Mode
How to Do Plug and Play (via USB Cable)
Android
- Select the Android on the main menu of the projector, and then select Plug and Play menu by pressing the “Enter” key.
- Download and install EZCast app from Google Play Store or scan the QR code shown on screen.
- Connect your mobile to the projector via the mobile USB charging cable, and then enable “USB Tethering” in the Setting of your mobile.
- Enable EZCast app and select “Beam-XXXX” to enjoy your projection .
iOS
- Select the iOS on the main menu of the projector, and then select Plug and Play menu by pressing the “Enter” key.
- Download and install EZCast app from App Store or scan the QR code shown on screen.
- Connect your mobile to the projector via mobile USB charging cable, and then choose “Trust This Computer” to start your projection.
Windows 10
- Select Windows on main menu of projector, and then select Plug and Play menu by pressing “ENTER” key.
- Install EZCast app on your PC. Please visit https://www.ezcast.com/app to download EZCast app.
- Connect your PC to the projector via USB A-to-A cable.
- Enable EZcast app on your PC and select “Beam-XXXX” to enjoy your projection.
MacOS
- Select MacOS on main menu of projector, and then select Plug and Play menu by pressing “ENTER” key.
- Install EZCast app on your PC. Please visit https://www.ezcast.com/app to download EZCast app.
- Connect your PC to the projector via USB A-to-A cable.
- Enable EZcast app on your PC and select “Beam-XXXX” to enjoy your projection.
How to Do Wireless Display
Android
- Select Android on main menu of projector, and then select Wireless menu by pressing “ENTER” key.
- Select mirroing function in the setting of your phone and find “Beam-xxxx” device shown on device list to start your mirroring.
Note 1 : The naming of the mirroring function varies different brands. Visit https://www.ezcast.com/usage/androld/ezmlrror for demos.
Note 2: Compatibility: Android 5.0 or above.
iOS
- Select iOS on main menu of projector, and then select Wireless menu by pressing “ENTER” key.
- Make sure both of your projector and mobile ara connected to the same WiFi router.
- Go for Screen Mirroring of your mobile and select the “Beam-XXXX” shown on the list to start projection.
Windows 10
- Select Windows 10 on main menu of projector, and then select Wireless menu by pressing “ENTER” key.
- Make sure both of your projector and computer are connected to the same WiFi router.
- Click quick key by@]+ C!:fil on the computer, and connect to the device named by “Beam-XXXX” to start your projection .
Note: Please upgrade your windows 10’s operation system to the latest version.
MacOS
- Select MacOS on main menu of projector, and then select Wireless menu by pressing “ENTER” key.
- Make sure both of your projector and computer are connected to the same WiFi router.
- Click for Screen Mirroring icon on your computer and select the “Beam-XXXX” shown on the list to start your projection.
Google Home Screen Mirroring (Android Only)
- Select Android on main menu of projector, and then select Google Home menu by pressing “ENTER” key.
- Make sure both of your projector and mobile are connected to the same WiFi router.
- Download and install Google Home app from Google Play Store.
- Enable Google Home app and go to Account >> Mirror Device >> select the “Beam-XXXX” shown on the list to start your projection.
EZCast
- Select EZCast on main menu of projector and Make sure both of your projector and mobile are connected to the same WiFi router.
- Install EZCast app on your device. Please download the app from application market for your mobiles or visit https://www.ezcast.com/app to download EZCast app for PC.
- Enable EZCast app on your device, and then click icon and select the “Beam-XXXX” shown on the list to start your projection.
FAQ
Documents / Resources
 | Projectors |
References
- User Manualmanual.tools
Published: September 26, 2021
Updated: October 3, 2021
Hi I have a Acer Open PV12 Fire legend portable projector and it comes up with a red light when trying to charge it to power using at the DC15 V outlet and it won’t power on… I have only used it twice what could be wrong?
It doesn’t matter how long I hold down the power button, it won’t restart?
Thankyou
It doesn't matter how long I hold down the power button, it won't restart?
Thankyou
Why is my AOPEN PV12 Fire Legend projector showing a red light and failing to power on even when connected to the DC 15V outlet?
Based on the AOPEN Projector user guide, here are the steps to troubleshoot your PV12 Fire Legend projector not powering on:
If the red light persists and the unit does not respond to a 3-second long press after several hours of charging, the manual advises that you should not attempt to disassemble the device yourself. Please contact customer support or return the device for repair as it may have an internal circuit or battery issue.
Read the full Q&A page
accidental enter wrong language how do I fix this back to English???
How do I change the language back to English on my AOPEN projector?
To change the language back to English on your AOPEN projector, follow these steps using your remote control:
If you are unable to find the menu due to the language barrier, you can also use the Reset all option within the Setting menu to restore the projector to factory defaults, which will prompt you to select your preferred start-up language again.
Read the full Q&A page
Image on wall from projector upside down what may be the problem
Why is my projector image upside down and how do I fix it?
If your AOPEN projector image is upside down, it is likely because the projection mode is set incorrectly (e.g., set to 'Ceiling' mode instead of 'Desktop' mode). To fix this, follow these steps:
If you cannot find the specific orientation setting, you can also use the Reset all option in the Setting menu to restore the projector to factory defaults, which should return the image to the standard upright orientation.
Read the full Q&A page