anko 43056125 Bluetooth Party Speaker User Manual
anko 43056125 Bluetooth Party Speaker

Warning

Electric Warning Icon

CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN

Caution Icon

 The lighting flash with arrowhead symbol, with an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERICEALBE PARTS INSIDE REFEER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended alert the user tithe presence of important operating and maintenance (servicing) instructions in the l iterature accompanying the appliance.

Important precautions:

  1. . The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
  2. Minimum distances 100 cm around the apparatus for sufficient ventilation.
  3. The ventilation should not be impeded by covering the ventilation opening swith items, such as news papers, table-cloths or curtains.
  4. No naked flame sources such as lighted candles,should be placed on the apparatus.
  5. When the mains plug or and appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
  6. Working temperature:-10℃~+45℃.
  7. Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use, storage or transportation.
  8. Replacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable liquid or gas.
  9. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
  10. Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
  11. A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
  12. The use of apparatus in moderate climates.
  13. Attention should be drawn to the environmental aspects of battery disposal.
  14. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
  15. Excessive sound pressure from earphones and headphones can cause hearing loss.
  16. The internal battery is non-user replaceable.
  17. Do not use this apparatus near the water.

Your Party Speaker

Introduction

With this unit, you can:

  • Enjoy audio from USB storage Devices, and other external device;
  • Listen to radio stations.

What’s in the box

Check and identify the contents of your package:

  • Speaker
  • Remote control
  • User manual
  • Line-in/FM Antenna Cable( the same one cable)
  • AC Power cable

Product Overview

Overview of the Top control panel
Product Overview

  1. Display Window
  2. Line-in Input jack
  3. Previous button
  4. Play/Pause button
  5. EQ button
  6.  Power ON/OFF button
  7. Volume/MIC Menu button
  8. Next button
  9. Mode button
  10. Bass button
  11. USB Input jack
  12. LED ON/OFF button

Overview of the Rear Panel
Product Overview

  1. Guitar Input jack
  2. Microphone Input jack
  3. Power ON/OFF Button
  4. AC Power Input jack

Overview of the Remote Control
Product Overview

  1. Power function key
  2. Menu function key
  3. Volume+ function key
  4. Play/Pause function key
  5. Previous function key
  6. Volume- function key
  7. Channel- function key
  8. Mute function key
  9. Bass function key
  10. Mode function key
  11. Next function key
  12. Scan function key
  13. Channel+ function key
  14. EQ function key

Get started

Warning Icon Caution

  • Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation

Always follow the instructions in this chapter in sequence.

Connect power

Warning Icon Caution

  •  Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on back or the underside of the unit.
  • Risk of electric shock! When you unplug the AC power cord, always pull the plug from the socket. Never pull the cord.

Before you connect the AC power cord, make sure that you have completed all other connections
Product Overview

Prepare the remote control

To insert the remote control batteries: 

  1. Open the battery compartment.
  2.  Insert 2 x AAA batteries with correct polarity (+/-) as indicated. The 2xAAA battery not include in our products, please purchase from Authorised Seller.
  3.  Close the battery compartment.

Please Note: 

  • If you are not going to use the remote for a long time, remove the batteries.
  •  Do not use old and new or different type of batteries in combination
    Batteries contain chemical substances, so they should be disposed of properly.

Turn On

  1. Connect the AC power cable and plug to the wall socket;
  2. Press the “POWER” button to o “ON” status to power on the speaker.
    The speaker will be powered by AC power and set the power switch on rear panel to ON
    position.
  3. Press the POWER button on the top panel or on the remote control to turn it into Standby mode,Press the POWER button on the top panel or on the remote control to turn off the speaker and get into Standby mode, press for a few seconds again to turn on the speaker.

Caution: 

If you do not use this unit for a while, please switch the “POWER” button to “OFF” status, and disconnect the AC power cable of this unit

Charging the internal Battery 

The speaker comes with a built-in rechargeable battery, follow the below steps to charge it:

  1. Connect the power cable and plug to the wall socket on the rear panel to start charging.
  2. Turn on the power ON/OFF button on rear and top panel, there is a battery indicator light on the bottom left corner of the display panel, it will light up and slowly flash, that is being charge.
  3. When the battery indicator light on the top left corner of the display pane light up, the battery is fully charged, then unplug the power cable to stop charging, both top and bottom indicator light will turn off automatically.

Intrenal Battery Level indicator 

  1. When the battery is running out, the battery indicator light on the bottom left corner light up and quickly flash.
  2. During playing, if you hear a “DI” sound from the speaker means the battery is running out and the speaker will turn off after 1 minute.
  3. Please pay attention to the speaker sound, if the sound becomes abnormal, please charge the internal battery on time to keep the battery life.

Note: please fully charge the product when it is not going to be used for a long time and charge once a month to keep longer battery life.

Play

Basic key play operations 

You can control play through following operations.

Key

Function

Button icon

  1. Press this previous button for previous track when playing music on USB or Bluetooth mode.
  2. In FM mode, short press this button to adjust FM frequency for 0.1MHz, or long press this button to search FM radio from 108-87.5MHz automatically.
Button icon
  1. Press this PLAY/PAUSE button to play or pause the music when playing music on USB or Bluetooth mode.
  2. Or press for a few seconds to disconnect the Bluetooth if speaker at Bluetooth mode
Button icon Press this EQ button to switch the different music effect. Note: It cannot switch if the BASS is on
Button icon Press the POWER button to turn off the speaker and get into Standby mode, press for a few seconds again to turn on the speaker.
Plug In Insert the Line-in cable to external device
USB Socket Insert the USB driver to USB socket to play music.
Button icon
  1. press this previous button for previous track when playing music on USB or Bluetooth mode.
  2. In FM mode, short press this button to adjust FM frequency for 0.1MHz, or long press this button to search FM radio from 87.5-108MHz automatically.
Button icon Press this M button for function mode switching between Bluetooth/AUX/USB/FM modes
Volume Button
  1. Turn this VOLUME knob for volume increase or decrease when playing music, the display will show from U 00 to U 40 .
  2. Press this VOLUME knob for one time to turn to the echo volume level of microphone if using wired microphone, the display will show “ E ”, then turn the knob to adjust the sound volume of microphone echo.
  3. Press this VOLUME knob for twice to turn to the volume level of microphone if using wired microphone, the display will show “ C ”, then turn the knob to adjust the sound volume of microphone.
  4. Press this VOLUME knob for twice to turn to the volume level of guitar if using wired guitar, the display will show “ C ”, then turn the knob to adjust the sound volume of guitar.
Button icon Press this BASS button for turn on or off the bass strong effect.
Led Button Press this LED button for turn on and off, or switch the light effect
AC Input Jack AC Input jack
Mic Jack Insert the 6.35 wired microphone to the MIC jack.
Guitar Jack Insert the 6.35 Guitar to the GUITAR jack.

 

Play from USB

Make sure that the USB storage device containers playable audio in supported MP3 format.

  1. Press Button icon or Button icon key to select
  2. Press Button icon key to play or pause

Important:

USB socket is only for music playing, not support charging.

The MAX memory size of USB:32Gb.

USB memory device should be formatted as FAT32.

Listen to radio

Turn on FM radio stations

Note

  • Make sure that you have connected and fully extended the supplied FM antenna.
  • The FM Antenna cable is the same as Line-in cable.
  1. Insert the Line-in/ FM Antenna Cable to the Line-in jack
  2. Press the M/ MODE button on the Top Control panel or on the remote control to switch to FM mode
  3. Short press Button icon button to adjust the FM frequency for 0.1MHz, or long press to search the FM radio automatically from 108~87.5MHz.
  4. Short press Button icon button to adjust the FM frequency for 0.1MHz, or long press to search the FM radio automatically from 87.5~108MHz.
  5. Presss SCAN key on the remote control to search FM radio stations automatically.
  6. Press CH- / CH+ key on the remote control to select the previous or next radio station.

Connect with Bluetooth

  1. Press the M/MODE button on the Top Control panel or on the remote control to switch to the BLUETOOTH CONNECT mode, BF Button will be displayed on the screen.
  2. Open the Bluetooth on the external device (must have Bluetooth function), and the name “43056125” will show on the device, please try to connect it.
  3. Once connected, you can hear a small sound from the speaker.
  4. You can use the Button icon or Button icon key on the Top Control panel to control the tracks of the external device.
  5. Press Button icon button on the top control panel to disconnect the bluetooth.(This Button icon on remote control not work for bluetooth disconnect function.)
    Note: no password needed for connecting.

Connect with Line-in

  1. Press the M/MODE button on the Top Control panel or on the remote control to switch to the Line-in mode, (LINE) will be displayed on the screen.
  2. Connect an external audio source use a supplied line-in cable.
  3. Once connected,turn on your external device music
    Caution: Please turn off party speaker before connect Line-in cable in order to avoiding unexpected noise.
    Line Connections

Connect with Wired Microphone/Guitar

Mic Jack
Insert 6.35mm wired microphone to play with microphone.

Guitar Jack
Insert 6.35mm wired guitar to play with guitar.

Volume Button
When playing with the wired microphone/guitar, please press this knob to adjust the sound volume level of microphone/guitar.

Microphone: 

  1. Turn this VOLUME knob for volume increase or decrease when playing music, the display will show ” U “.
  2. Press this VOLUME knob for one time to turn to the microphone echo volume adjust mode, the display will show ” E “, then turn the knob to increase or decrease the  microphone echo volume if using wired microphone..
  3. Press this VOLUME knob for twice to turn to the microphone volume adjust mode, the display will show ” C “, then turn the knob to increase or decrease the microphone volume if using wired microphone.

Guitar: 

If using wired guitar, the volume instruction the same as above 3 of microphone.

Important Notes 

While using the microphone, avoid being put the microphone opposite the bass of Speaker, as they may have Whistler Noisy. To get the best singing performance, keep the micro phone within 5-15cm from your mouth and at a 45 degree angle.

Caution: Please do not put the microphone directly face to the speaker, it may damage the speaker

Product information

Specifications

Amplifier
Output power 60W
Input Sensitivity ≥500mV
FM
FM range 87.5-108MHZ
Speaker
Treble Speaker 2 Inch
Bass Speaker 5.25 Inch
General information
AC Power AC220-240V~ 50Hz
Battery Rechargeable battery

USB play ability information Compatible USB storage devices: 

  • USB flash memory (USB 2.0 or USB 1.1)
  • USB flash players(USB 2.0 or USB 1.1)
  • Memory cards (requires an additional card reader to work with this apparatus)

Supported for formats: 

  • USB or memory file format FAT32
  • MP3 bit rate (data rate):32-320Kbps and variable bit rate
  • Directory nesting up to a maximum of 8 levels
  • Number of albums/folders:maximum 99
  • Number of tracks/titles:maximum 999
  • File name in Unicode UTF8 (maximum length:32 bytes)

Unsupported formats: 

  • Empty albums: an empty album is an album that does not contain MP3.
  • Unsupported the file formats are skipped. For example, Word documents (.doc) or MP3 files with extension .dlf are ignored and don’t play

Troubleshooting

Warning Icon Warning: Never remove the casing of this speaker

If you encounter problems when using this speaker,check the following points before requesting service

No power 

  • Ensure that the AC power plug of the speaker is connected properly.
  • Ensure that there is power at the AC outlet.

No sound or poor sound 

  • Adjust the volume.
  • Disconnect the headphones.
  • Check that the speakers are connected correctly.
  • Check if the stripped speaker wires are clamped.

No response from the speaker

  • Disconnect and reconnect the AC power plug, then turn on the speaker again.

Remote control does not work 

  • Before you press any function button, first select the correct source with the remote control instead of the main unit.
  • Reduce the distance between the remote control and the unit.
  • Insert the battery with its polarities(+/- signs) aligned as indicated.
  • Replace the battery.
  • Aim the remote control directly at the sensor on the front of the speaker.

USB device not supported 

  • The USB device is incompatible with the unit. Try another one.
  • The USB device is incompatible with the speaker or the USB damaged.

Poor radio reception 

  • Increase the distance between the speaker and your TV.
  • Full extend the FM antenna.
  • Put the speaker at a open area to search radio.

Bluetooth can not search or connect 

  • If other devices are connected to the machine, please disconnect other Bluetooth devices and use the new device to search and connect again.
  • Turn off the Bluetooth of your device , then turn on your device Bluetooth again, search and connect. Or turn off the speaker and turn on again and switch to Bluetooth mode.

Warranty

12 Month Warranty

Thank you for your purchase from Kmart.

Kmart Australia Ltd warrants your new product to be free from defects in materials and workmanship for the period stated above, from the date of purchase, provided that the product is used in accordance with accompanying recommendations or instructions where provided. This warranty is in addition to your rights under the Australian Consumer Law.

Kmart will provide you with your choice of a refund, repair or exchange (where possible) for this product if it becomes defective within the warranty period. Kmart will bear the reasonable expense of claiming the warranty. This warranty will no longer apply where the defect is a result of alteration, accident, misuse, abuse or neglect.

Please retain your receipt as proof of purchase and contact our Customer Service Centre on 1800 124 125 (Australia) or 0800 945 995 (New Zealand) or alternatively, via Customer Help at Kmart.com.au for any difficulties with your product. Warranty claims and claims for expense incurred in returning this product can be addressed to our Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

For New Zealand customers, this warranty is in addition to statutory rights observed under New Zealand legislation.

Documents / Resources

anko 43056125 Bluetooth Party Speaker [pdf] User Manual
43056125, Bluetooth Party Speaker

Leave a comment

Your email address will not be published.