![Anker SoundCore User Manual [Pairing Instructions] pdf](/img/pdf.png){kind=small}
Anker SoundCore
Anker SoundCore
For FAQs and more information, please visit
What’s Included
At a Glance
Using Your SoundCore
1. Turn on / off
Note: SoundCore will automatically turn off after 10 minutes if no device is connected.
2. Charge your SoundCore
Flashing red Low power
Steady red Charging
Off Fully charged
Use the included USB cable to charge your SoundCore and make sure it is fully charged before first use.
Pair with your device
Un-pair connected device and re-enter pairing mode
Rapidly flashing blue Pairing mode
Steady blue Connected to a device
When turned on, SoundCore will automatically connect to the last connected device if available. If not, SoundCore will enter pairing mode. Having connection problems? Remove SoundCore from your device’s Bluetooth history, ensure it’s less than 3 feet away then try pairing again.
Connect via AUX
- SoundLine AUX cable sold separately.
- Rapidly flashing blue AUX mode
When using AUX mode, control audio playback via the connected device.
Controls
Play – pause
Skip forward
Volume up / down
Answer / End call
Reject call
Put current call on hold and answer incoming call
Specifications
- Input : 5 V = 1 A
- Audio output : 3 W × 2
- Charging time : 5 – 6 hours
- Play time (varies by volume level and content) : 24 hours
- Size : 165 × 45 × 54 mm 6.5 × 1.8 × 2.1 in
- Weight : 365 g / 12.9 oz
- Range : 20 m / 66 ft
Attention
Use original or certified cables
Don’t expose to liquids
Don’t disassemble
Avoid dropping
Avoid extreme temperatures
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio / TV technician for help.
RF Warning Statement: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Trademark
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Anker Technology Co., Limited is under license.
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
Hereby, Anker Technology Co., Limited declares that the radio equipment type A3102 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
www.anker.com
www.ankeroficial.com.br
suporte@ankeroficial.com.br
- BT Maximum output power: 1.5dBm
- BT Frequency band: 2.4G band (2.4000GHz-2.4835GHz)
IC NOTICE TO CANADIAN USERS
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003.
warranty
- 18-month limited warranty
Customer Service
- Lifetime technical support
- suporte@ankeroficial.com.br
- TEL: 1-800-988-7973
- 00477-18-10554
- Mon-Fri 9:00-5:00 PST (US)
Thanks
Questions about Anker SoundCore ? Post in the comments!
DOWNLOAD RESOURCES
FAQ’S
Ensure Bluetooth is enabled on your device, then try pairing again.
Ensure you are within 3 feet of SoundCore. If the problem persists, remove SoundCore from your device’s Bluetooth history and try again.
I can’t connect to SoundCore via AUX. How do I fix this?
Make sure you are using the included SoundLine AUX cable, and that it is fully inserted into both ends. If the problem persists, remove SoundCore from your device’s Bluetooth history and try again.
This may be due to a weak connection between your phone or tablet and the AUX cable. Try moving the cable around to find a better connection point, or use a different AUX cable if available. If you continue to experience problems, please contact our support team at www.anker.com/support .
This may be due to a weak connection between your phone or tablet and SoundCore. Try moving your phone or tablet closer to SoundCore until you find a good connection point, then try playing music again. If you continue to experience problems, please contact our support team at www.anker.com/support .
Anker doesn’t provide a weatherization rating, so I wouldn’t leave this speaker exposed to the elements or use it too close to the edge of a pool.
It’s loud enough to fill a small room, but will struggle to be heard on a noisy beach or street. This is to be expected from such a compact speaker with stellar battery life but it’s a trade-off nonetheless. Those who want 360-degree audio, waterproofing, and better sound should look at the UE Wonder boom.
Featuring a customized 3′ Runtrack Speaker driver with BassUp™ technology, it delivers a wide range of high-quality audio frequency at 10 watts. The Icon connects to devices via Bluetooth 5.0 and provides 12 hours of playtime on a single charge.
Compatibility: Bluetooth; works with all Mac’s, iPad’s, iPhone’s and iPods that have Bluetooth. This means in practice all Mac’s, iPads and iPhones and all iPod touches.
Anker SoundCore 2 Portable Bluetooth Speaker with Better Bass, 24-Hour Playtime, 66ft Bluetooth Range, IPX5 Water Resistance & Built-in Mic, Dual-Driver Wireless Speaker (Red)
The Soundcore app is available on iOS and Android devices.
The SoundCore will take about 3 hours to charge with a 2 amp charger (like a tablet charger or Anker wall charger) or about 6-8 hours with a phone charger or laptop USB port. When the LED turns white it will have finished charging.
Your Bluetooth device may be out of range for connection. To solve this remove any obstacles between the speaker and your device, move as close as possible, and try to connect.
VIDEO
www://anker.com/
I am trying to connect this device to my Playstation 3, but it asks for a passkey. There is no passkey i am aware of and I had this for a long time so I do not have the original box. Not even the online manual had a passkey for Playstation devices.
Default passkeys for SoundCore devices are usually either 0000 or 8888
I recently purchased an Anker Sound Core 2 with the built-in mic. I hope to use the speaker as a sound output only. We use the speaker for Skype and the other end only hears themselves due to the feedback from the mic being right next to the sound speaker. Is there a way to turn off the build-in mic?
Is the aux connector truly stereo? I have tried four or five different cables which I *KNOW* are three-conductor (TRS) cables, yet the audio that comes through is always monaural, both channel playing through both speakers.
Dead doesn’t want to be charged, why huh?
Mati tidak mau dicharger kenapa ya
I have two soundcare A3102 speakers, and I have tried to connect them together, but it was impossible. Is there any configuration to be able to do it? Or only the Soundcare 2 can be connected to each other?
Tengo dos parlantes soundcare A3102, y he tratado de conectarlos entre sí, pero me ha sido imposible. Existe alguna configuración para poder hacerlo? O solo los Soundcare 2 se pueden conectar ente sí?