AMP AFL-4010 DiffusePro Flood Light User Guide

This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.

Make sure the power is turned OFF before installing or servicing this luminaire.

WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

Wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.

The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when turning on.
Do not touch the hot lens, guard or enclosure.

Keep lamp away from materials that may burn.
Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.

Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS

A. (1) Stake

B. (1) Luminaire

PRODUCT DIMENSIONS

Install Stake

Determine the desired location for mounting the luminaire. Hammer the stake into the ground until the flange of stake is flush to grade. To avoid damage to the stake, place a board on top of stake while hammering.
NOTE: If the ground is hard and the stake is difficult to install, make a crosscut in ground using a flat shovel.

Remove Cover and Gasket with Lens

Loosen the lock screws and remove the cover and gasket with the lens from the luminaire to expose the socket.

Install Bulb

Insert the bulb with correct wattage and type marked on the luminaire label.

CAUTION: Do not exceed maximum wattage marked on luminaire label.

NOTE: DO NOT touch bulb with bare hands. Use soft cloth to handle lamp.

Install Gasket with Lens and Cover

Decide which lens you would like to use with this fixture. Then install the gasket with your lens of choice back onto the luminaire and secure with the lock screws.

Install Luminaire to Stake

Clear away an area in the ground at the wireway slot on top of the stake. Lay the luminaire pigtail into the wireway slot and screw the fixture on to the stake. Tighten the hex nut on the luminaire against the stake and tighten until snug.

Wire Connections

Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.

1-813-978-3900 • Mon-Fri 9am-6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved. customersupport@amplighting.com • amplighting.com

FAQ

Q: Can I use a power supply with more than 300 watts?
A: No, this luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts. Using a higher wattage power supply may damage the luminaire.
Q: How deep should I bury the low voltage cable?
A: The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm). Ensure it is buried at a depth within this range for proper installation.

Documents / Resources

AMP AFL-4010 DiffusePro Flood Light [pdf] User Guide
AFL-4010 DiffusePro Flood Light, AFL-4010, DiffusePro Flood Light, Flood Light

References

User Manual

AMP AFL-4010 DiffusePro Flood Light

Specifications

IMPORTANT SAFETY INSTRUCTIONS: