Document

AMP - LOGO

INSTALLATION & MAINTENANCE GUIDE

AMP® Low Voltage Landscape Lighting
AMP® Stagecoach LED Path & Area Light
APL-3023-4-B-BZ

Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com

INSTALLATION & MAINTENANCE GUIDE

Stagecoach LED Path & Area Light
APL-3032-4-B-BZ
Important Safety Instructions: Read Before Installation!
This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.

These instructions do not intend to cover all variations in installation, operation maintenance, or mounting situations.

  1. Make sure that the power is turned OFF before installing or servicing this luminaire.
  2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from the pool, spa, or fountain.
  3. This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
  4. Wiring connections must be made with UL-listed wire connectors that are suitable for outdoor use.
  5. Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
  6. The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).

Important Safety Instructions!

THE LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.

  1. Turn off/unplug and allow to cool before reducing the lamp.
  2. Lamp gets HOT quickly!
  3. Do not touch the hot lens, guard, or cowl.
  4. Keep the lamp away from materials that may burn.
  5. Do not touch the lamp at any time.
  6. Use a soft cloth.
  7. Oil from the skin may damage the lamp.
  8. Do not operate the fixture with a damaged or missing lens or shield.

Package Contents

A. (1) Fixture
B. (1) Stem
C. (1) Ultra Realistic LED Moving
Flame Bi-Pin Candle
D. (1) 17” Stake

Additional Parts Required (sold separately)

A. (1) LED SCB Lamp

Product Dimensions

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - TOP VIEW

Remove the Hat

Remove the hat from the stem by removing the set screws from the hat mount.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Remove the Hat

Reinstall Hat

After installing the LED lamp into the socket, place the hat back onto the mount at the top of the stem.
Secure both pieces in place with the set screws previously removed. Hand tightens until snug.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Reinstall Hat

Install LED Lamp

Insert the lamp with the correct wattage and type marked on the fixture label.
CAUTION: Do not exceed maximum wattage marked on the luminaire label.
NOTE: DO NOT touch the bulb with bare hands. Use a soft cloth to handle the bulb.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Install LED Lamp

Remove Upper Part of Hat

Remove the upper part of the hat by loosening the set screws.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Remove Upper Part of Hat

Install LED Bi-Pin Candl

Insert Ultra Realistic LED Moving Flame Bi-Pin Candle.
CAUTION: Do not exceed maximum wattage marked on the luminaire label.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Candle

Reinstall Upper Part of Hat

Place the upper part of the hat back onto the lower part of the hat and secure with the set screws previously removed. Hand tightens until snug.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Part of Hat

Install Stem

Pass the supply wires through the stem and extension. Then thread the extension onto the stem. Hand tightens until snug.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Install Stem

Install Stake and Conduit

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Stake and Conduit

Dig a hole in the ground for the conduit runs and the stake. Install the conduit. Slide the stabilizer grid onto the stake and secure with the screws. Place the stake over the conduit runs. Backfill against the mounting stake.

Remove Cap from Stake

Remove the cap from the stake by loosening the set screws.

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Cap from Stake

Install Cap to Fixture

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Cap to Fixture

Wire Connection and Fixture Installation

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting - Wire Connection and Fixture

Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.

Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
Specifications and product details are subject to change without notice.
© Copyright 2021, AMP ®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
www.amplighting.com
IS-APL-3023-4-B-BZ-ver3.pdf

Documents / Resources

AMP Lighting APL-3023-4-B-BZ Low Voltage Landscape Lighting [pdf] Installation Guide
Stagecoach LED Path Area Light, APL-3023-4-B-BZ Low Voltage Landscape Lighting, APL-3023-4-B-BZ, Low Voltage Landscape Lighting

Leave a comment

Your email address will not be published.