QUICK START GUIDE
Ready from the first scan.
Install the battery, charge the device, power on, and begin barcode data collection.
ANDROID 14+ QCM4490 CPU | 2.4 GHZ IP68
8 GB RAM | 128 GB FLASH WI-FI 6E | BLUETOOTH BLE 5.2
5G / LTE / CBRS READY

What is in the box
Contents vary when optional charging items are ordered.
INCLUDED
Every PDX50 package
- PDX50 mobile computer
- Rechargeable main battery
- Adjustable hand strap
IF ORDERED
Packed with the PDX50
- AML power supply
- USB-C charging/data cable
These items are purchased separately. When ordered with the device, they ship in the same PDX50 box.
DEVICE OVERVIEW
Controls and features
The numbered views identify the controls, connections and service points of the PDX50.

NUMBERED LEGEND
- Proximity sensor
- Microphone
- Receiver
- Notification LED
- Front camera
- Barcode scanner
- Touchscreen
- Left scan button
- Volume down
- Volume up
- Power button
- Programmable button (PTT capable)
- Right scan button
- Rear camera
- Camera flash
- Battery release latch
- Upper hand-strap mount
- Main battery
- Lower hand-strap mount
- Speaker
- USB-C port
- Charging contacts
- Microphone
- NFC reading area
- Accessory I/O connector
- Laser safety label
FIRST USE
Prepare, charge, power on
Complete these steps before using the PDX50 for barcode data collection.
- Install cards, if required
With the PDX50 powered off, remove the main battery. Insert the nano-SIM and/or microSD card in the marked slot and orientation. Never force a card into place.
Card availability and cellular service depend on the PDX50 configuration. - Install the battery
Align the battery with the rear compartment, seat it fully, and press until securely latched. Fit the included hand strap and confirm that it does not interfere with the battery latch.
Use only AML-approved PDX50 batteries (AML model 180-5300). - Charge the PDX50
Connect the optional AML power supply and
USB-C cable, or place the PDX50 in its charging cradle. The cradle is supplied with its own power supply.
RED Charging GREEN Charged - Turn on and complete setup
Press and hold the Power button for 3 seconds.
Follow the Android setup prompts supplied with your AML configuration. AML Barcode Service initializes automatically during startup.
A momentary Power-button press puts the
PDX50 in standby or wakes it.
CHARGING NOTE
Allow the battery to charge fully before the first extended work shift. Keep the USB-C port and cradle contacts clean and dry.
FIRST-BOOT CONFIGURATION
Set up in a few guided steps
The AML Setup Wizard appears when the PDX50 is started for the first time. Complete it before deploying the device.

Setup by barcode
On the Welcome screen, scan an AML-approved setup barcode to apply a predefined industry or application deployment. Depending on the barcode, the PDX50 can be enrolled into AML Device Manager (ADM) or supported third-party applications such as Soti, Velocity, InTune.
If directed by barcode
AML Setup runs only when instructed by the enrollment barcode. It performs the requested setup, then closes automatically.
RECOMMENDED
Although the wizard provides a Skip option, completing Wi-Fi and time-zone setup is recommended before application enrollment and normal operation.
DAILY USE
Your first scan
AML Barcode Service starts automatically. No separate scanner utility needs to be opened at startup.
- Connect
Open Settings and connect to the required Wi-Fi network. - Aim
Place the barcode inside the aiming pattern. - Scan
Press either blue scan button and hold steady until decoded.
If data does not appear, confirm the receiving app is active and the scan window is unobstructed.
Power and warm battery swap
STANDBY Press the Power button momentarily.
POWER MENU Press and hold Power to display Battery Swap, Power Off and Restart.
BATTERY SWAP Select Battery Swap, follow the on-screen prompt, then replace the main battery.

Help and support
TECHNICAL SUPPORT
877-842-3990
support@amltd.com
www.amltd.com
7361 Airport Fwy, Richland Hills, Texas 76118
Use safely
- Use only AML-approved batteries and charging accessories.
- Do not charge when ports or contacts are wet.
- Do not disassemble, puncture or short-circuit the battery.
KEEP IN TOUCH
Register your PDX50
Registering your PDX50 is quick and easy. Registration can help AML expedite support requests and keep you informed about news and information that may affect your AML devices.

Disclaimer and notices
AML reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult with AML to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of AML. AML shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of AML.
LATEST INFORMATION
Specifications and procedures may change. Visit www.amltd.com or contact AML Technical Support at 877-842-3990 for current information.
AML PDX50 Quick Start Guide
Rev A | August 2026
Documents / Resources
![]() | PDX50 |
References
- AML Mobile Computers and Kiosks – Since 1983, AML has helped warehouses, manufacturers, and retailers improve productivity with rugged mobile computing solutions designed and supported in the USA. Our hardware, software, and responsive U.S.-based team delwww.amltd.com
- Product Registration – AMLwww.amltd.com
- AML Mobile Computers and Kioskswww.amltd.com
- User Manualmanual.tools
