• Connect the included power adapter to the device and plug into a power outlet.
• Connect the device into an HDMI port of a display device.
• Wait until the device boots up.

PAIR YOUR REMOTE:

• Follow the on-screen instructions to pair the supplied remote.

SET UP YOUR DEVICE:

• Follow the on-screen instructions to setup a wireless network connection and user account.

Your device is now ready for use. Stream content of your choice through applications found on the home scree.

Safety and Compliance Information

Using Your Device Around Other Electronic Devices

The Device, uses, and can radiate radio frequency (RF) energy and, if not used in accordance with its instructions, may cause interference to radio communications and electronic equipment. External RF signals may affect improperly installed or inadequately shielded electronic operating systems, entertainment systems, and personal medical devices.

While most modern electronic equipment is shielded from external RF signals, if in doubt, check with the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with your physician or the manufacturer to determine if they are adequately shielded from external RF signals.

There are some places where RF signals could constitute a hazard, such as health care facilities, and construction sites. If you are not sure, look around for signs indicating that two way radios or mobile phones should be turned off.

Other Safety Considerations

• Do not touch your device or any wires connected to your device during a lightning storm.
• Small parts contained in your device and its accessories may present a choking hazard to small children.
• Your device is shipped with an AC adapter. Your device should be powered using the AC adapter and USB cable included with the device, or another USB cable approved for use with your device with a compatible AC adapter.

FCC Compliance Information

Radio Frequency Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications that are not expressly approved by the party responsible for compliance could make the device no longer comply with the FCC Rules.

FCC regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.

Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.

Information on your device is on file with the FCC and can be found by inputting your device’s FCC ID, which can be found on the back of Device, into the FCC ID Search form available at transition.fcc.gov/oet/ea/fccid.

The party responsible for FCC Compliance is Amazon.com Services Inc. 410 Terry Ave North, Seattle WA 98109 USA.
Website link: www.amazon.com/devicesupport

Information Regarding Exposure to Radio Frequency Energy

The output power of the radio technology used in the Device is below the radio frequency exposure limits set by the FCC. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

IC Compliance Information

Radio Frequency Information

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.
This device for operation in the band 5,150–5,250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Devices shall not be used for control of or communications with unmanned aircraft systems.

Information Regarding Exposure to Radio Frequency Energy

This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

CAN ICES-3(B)/NMB-3(B)