ZigBee Smart plug
የተጠቃሚ መመሪያ
የምርት መግቢያ
የመሳሪያው ክብደት ከ 1 ኪሎ ግራም ያነሰ ነው. ከ 2 ሜትር ያነሰ የመጫኛ ቁመት ይመከራል.
የመጫኛ መመሪያዎች
- ኃይል አጥፋ
የኤሌክትሪክ ንዝረትን ለማስወገድ፣ ሲጭኑ እና ሲጠግኑ እርዳታ ለማግኘት አከፋፋዩን ወይም ብቃት ያለው ባለሙያ ያማክሩ።
- የወልና መመሪያ
መሣሪያውን ከማብራትዎ በፊት ትክክለኛውን ሽቦ ያረጋግጡ።
S1/S2 can connect with the rocker light switch, or it doesn’t connect. To ensure safety, do not connect the neutral wire and live wire to it.
ዝርዝሮች
የምርት ዓይነት | ዚግቢ ስማርት ተሰኪ |
ግቤት | 100-240VAC 50/60Hz |
ውፅዓት | 100-240VAC 50/60Hz |
Max.Lad | 10A/13A/16A/20A |
ዚግቢ | IEEE 802.15.4 2.4GHZ |
ቁሳቁስ | PC VO |
ባህሪያት
ZigBee plug is a smart Plug that adopts the ZigBee plug wireless protocol and connects to your internet through the ZigBee hub. You can turn on/off, schedule on/off, and share the device with your family to control together, and so on.
![]() | ![]() |
![]() | ![]() |
![]() |
The above functions are determined by the ZigBee Hub.
የአሠራር መመሪያ
- APP አውርድ
Please refer to the user guide of the hub to download the corresponding APP. below platforms are recommended:SmartThings Amazon Alexa ሁ - የሃብ ግንኙነት
Set the hub according to the user guide.Support ZigBee plug hubs as follows:
ኢኮ ስቱዲዮ
Echo Plus (ሞዴል፡ ZE39KL)
2ኛ Gen Echo Show (ሞዴል፡ DW84JL)
2ኛ Gen Echo Plus (ሞዴል፡ L9D29R)
ሳምሰንግ SmartThings ማዕከል
Philips Hueግንኙነቱ ካልተሳካ፣ እባክዎ መገናኛውን ወደ ስልክዎ ያቅርቡ እና እንደገና ይሞክሩ።
- አብራ
ካበራ በኋላ መሳሪያው ለመጀመሪያ ጊዜ ጥቅም ላይ በሚውልበት ጊዜ የማጣመሪያ ሁነታውን ያስገባል, እና የ LED ምልክት አመልካች ብልጭ ድርግም ይላል.The device will exit the pairing mode if no next operation for a long time. If you enter again, please long-press the manual switch for 5s until the LED signal indicator flashes and release.
- ከአሌክስክስ ጋር ይገናኙ
1. Power on the Plug
2. Ask, “Alexa, discover devices!
3. Plug ashes once it’s connected
4. Wait until Alexa finishes, check the new devices” First/Second….plug”
ከ SmartThings ጋር ይገናኙ
- Power up the smart bulb, bulb breathe 3 times, and enter the configuration state.
- Open the SmartThings app, and click”+”, click “Device”, click “SmartThings”, click “Lighting”, click ” Smart Bulb”, click “Start”, click “Next”, click “Skip the step”, click “Done”
የፋብሪካ ዳግም ማስጀመር
Long-press the configuration button for 5s until the LED signal indicator flashes and release, then the reset is successful. The device enters spairing mode.
If you pair the device with the hub again, please reset the device to factory default.
በቻይና ሀገር የተሰራ
ሰነዶች / መርጃዎች
![]() | የዚግቢ ብርሃን መቀየሪያ ሞዱል [pdf] የተጠቃሚ መመሪያ የመብራት መቀየሪያ ሞዱል፣ መቀየሪያ ሞዱል፣ ሞጁል |