Metra DP-7528 Enkel of Dubbel DIN Dash Panel Instruksie Handleiding
Metra DP-7528 Enkel of Dubbel DIN Dash Panel

KIT-KENMERKE

  • ISO DIN radio voorsiening met sak
  • ISO ODIN radio provision
  • Textured to match the factory dash.
  • Can also be used as a factory dash replacement with factory Mazda radios.

KIT KOMPONENTE

KIT KOMPONENTE

  • A) Radiobehuising
  • B) Radio trim panel
  • C) Radiohakies
  • D) Sak
  • E) #8 x 3/8″ Phillips skroewe (10)
  • F) Paneelknipsels (2)
  • G) #8 x 1/2″ Phillips screws (2)

BEDRADING EN ANTENNA VERBINDINGE (apart verkoop)

Bedradingskabel: 70-7901
Visit metraonline.com for audio/video and steering
wheel control interface options.
Antenneadapter: nie nodig nie

GEREEDSKAP BENODIG

  • Paneel verwyder instrument
  • Phillips skroewedraaier

Aandag! With the key out of the ignition, disconnect the negative battery terminal before Installing this product. Ensure that all Installation connections are secure before cycling the ignition to test this product.

DASH-DEMONTERING

From the center console: 

  1. Unclip ashtray to reveal (1) Phillips screw and remove. (Figure A)
  2. Open storage compartment and remove (2) Phillips screws. (Figure B)
  3. Locate the (2) Phillips screws on the front sides of the gear shifter trim panel and remove. (Figure C )
    DASH-DEMONTERING
  4. Unscrew gear shift knob. (Figure D)
  5. Unplug (2) connectors and remove the center console. (Figure E)
    DASH-DEMONTERING

Van die fabrieksradio -vergadering: 

  1. Unclip and remove center air vents to reveal (2) screws at the top of the radio trim panel. Remove the (2) screws. (Figure F)
  2. Unplug and remove the radio trim panel. (Figure G)
  3. Remove the (4) Phillips screws and pull out the radio assembly. (Figure H)
    DASH-DEMONTERING
  4. Remove (2) Phillips screws from the support bar on top of radio trim. Save bar for kit preparation. (Figure I)
  5. Remove (2) Phillips screws to remove the hazard switch. Save switch for kit preparation. (Figure J)
  6. Remove (1) screw from each air vent retaining clip. Keep together for (Figure I) kit preparation. (Figure K)
    DASH-DEMONTERING

KIT VOORBEREIDING

  1. Secure the support bar to the top of the radio housing using the (2) screws removed in step 4. (Figure A)
  2. Secure the hazard switch using the (2) #8 x 1/2″ Phillips screws provided. (Figure B)
  3. Transfer the retaining clips to the corresponding locations on the radio housing using screws removed in step 6. (Figure C)
    KIT VOORBEREIDING
  4. Attach the radio trlmplate to the radio housing using (6) of the supplied #8 x 3/8″ Philips screws. (Figure D)
  5. Attach the (2) panel clips to the radio housing. (Figure E)
    KIT VOORBEREIDING

KIT VERGADERING

ISO DIN radio voorsiening met sak 

  1. Attach the pocket to the radio brackets using (4) of the supplied #8 x 3/8″ Phillips screws. (Figure A)
  2. Slide the radio into the bracket/pocket (iii. assembly and secure it using the screws supplied with the radio. (Figure B)
  3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra -~ and/or AXXESS.
  4. Slide the radio into the sub dash and secure it using the factory hardware.
  5. Reassemble the dash in reverse order of  (Figure 8) disassembly using the new 7528 radio housing.
    KIT VERGADERING

ISO ODIN radio provision 

  1. Attach the radio brackets to the radio using the screws supplied with the  radio. (Figure A)
  2. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS.
  3. Slide the radio into the sub dash and secure it using the factory hardware.
  4. Reassemble the dash in reverse order of disassembly using the new 7528 radio housing.
    KIT VERGADERING

Het u probleme? Ons is hier om te help.

QR-kode

Icons  Kontak ons ​​tegniese ondersteuningslyn by:
386-257-1187
Icons Of per e -pos by:
[e-pos beskerm]

Ure vir tegniese ondersteuning (Eastern Standard Time) 

Maandag tot Vrydag: 9:00 – 7:00
Saturday: 10:00 AM- 7:00 PM
Sondag: 10:00 - 4:00

Logos KENNIS IS MAG
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school In our industry. Log onto www.installerinstituto.edu or call 386-672-5771 for more information and take stops toward a better tomorrow

Logos Metra beveel MO-gesertifiseerde tegnici aan

Dokumente / Hulpbronne

Metra DP-7528 Enkel of Dubbel DIN Dash Panel [pdf] Instruksiehandleiding
DP-7528, Single or Double DIN Dash Panel, DP-7528 Single or Double DIN Dash Panel, Double DIN Dash Panel, DIN Dash Panel, Dash Panel, Panel

Los kommentaar

Jou e-posadres sal nie gepubliseer word nie.