iPRO LOGOAdapterkas
Handleiding
iPRO WVQJB500 W Adapter BoxModel No
WV-QJB500-W
WV-QJB500-S
WV-QJB500-G

Voorsorgmaatreëls

  • Gebruik hierdie hakie nie, behalwe met geskikte kameras.
    As u dit nie nakom nie, kan dit lei tot beserings of ongelukke.
  • Verwys die installasiewerk na die handelaar.
    Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product.
    Raadpleeg die handelaar.
  • Install the product securely on a wall or a ceiling in accordance with the installation instructions.
    Versuim om dit na te kom, kan beserings of ongelukke veroorsaak.
  • Moenie die rande van metaaldele met u hand vryf nie.
    As u dit nie in ag neem nie, kan u beserings opdoen.

Lees ook die “Voorsorgmaatreëls” soos beskryf in die gebruiksaanwysings vir die kamera om aan te sluit, wanneer u hierdie produk gebruik. 

Voorwoord
Use this product when performing outdoor wiring of a box-type camera for outdoor or a wall mount bracket such as using a conduit.
For the latest information about the supported cameras, refer to our support webwerf
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information<ControlNo.:C0501,C0502>).

spesifikasies

Omgewingstemperatuur: -50 ° C tot +60 ° C (-58 ° F tot +140 ° F)
Dimensions: 115 mm (B) x 115 mm (H) x 40 mm (D)
(4-17/32 inches (W) x 4-17/32 inches (H) x 1-11/16 inches (D))
Mass: Approx. 430 g (0.95 Ibs)
Voltooi: Base bracket: Aluminum die cast
Attachment plate: Stainless
WV-QJB500-W: i-PRO white
WV-QJB500-S: Silver
VW-QJB500-G: Light gray

* This product consists of an attachment plate and a base bracket and they are separately packaged.

Voorsorgmaatreëls vir die installasie

  • In order to prevent injury, the product must be securely mounted to a ceiling or wall according to the Installation Guide of this bracket.
  • Maak seker dat u hierdie produk verwyder as dit nie meer gebruik sal word nie.

Standaard-bybehore

Operating Instructions (this document) …….. 1 pc.
Installed auxiliary wire* ………………………….. 1 pc.
Hexagon screw …………………………………. 5 pcs.
(M4 × 14 mm {9/16 inches}) (of them, 1 for spare)
Fixing screws for attachment plate ………… 5 pcs.
(M4 × 10 mm {13/32 inches}) (of them, 1 for spare)
Screw for temporary fixing …………………… 2 pcs.
(M3 × 3.5 mm {1/8 inches}) (of them, 1 for spare)

* An installed auxiliary wire is equipped with the attachment plate. 

Ander items wat benodig word (nie ingesluit nie)
Fixing screws (M4) …………………. 4 pcs.
BELANGRIK

Voorbereidings

Remove the tape fixing installed auxiliary wire (accessory) on the attachment plate.
When installing another bracket on this product
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an example.

  1. Remove the installed auxiliary wire (accessory) from the attachment plate. iPRO WVQJB500 W Adapter Box - FIG 1
  2. Attach the screw for temporary fixing (accessory) to the bracket to be installed on this product.iPRO WVQJB500 W Adapter Box - FIG 2 Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
  3. If necessary, install the attachment plate provided with the camera to WV-QWL500-W by following the instructions described in the Operating Instructions of WV-QWL500-W.

When using a conduit

  • Remove the cap for the female or thread for the conduit using a 5 mm hex wrench and attach the conduit.
    The female thread for the conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4 or ISO 228-1 (parallel pipe threads) G3/4.

iPRO WVQJB500 W Adapter Box - FIG 3

installasie

Step 1: Process the installation surface.
(Screw holes (4 places)/ Cable access hole (1 place))
When directly installing this product, process the installation surface.
let wel:

  • Determine the fixing screw hole diameter and depth in accordance with the specifications of the screws or anchors (x4) (M4: locally procured).
  • When wiring using a conduit, it is unnecessary to process the cable access hole on the installation surface. Make a fixing screw hole so that the cable access hole (for conduit) of the base bracket is arranged in the direction of the conduit.

Depending on the condition of the ceiling or the wall surface, the following five patterns of screw positions are available for fixation of the base bracket. Use only the holes of the same pattern (A – E) for mounting.

iPRO WVQJB500 W Adapter Box - FIG 4

Vertikale Horisontale
A 83.5 mm {3-9/32 inches} (82.5 mm {3-1/4 inches}) 46 mm {1-13/16 inches} (47.6 mm {1-7/8 inches})
B 46 mm {1-13/16 inches} (47.6 mm {1-7/8 inches}) 83.5 mm {3-9/32 inches} (82.5 mm {3-1/4 inches})
C* 83.5 mm {3-9/32 inches} (83.3 mm {3-9/32 inches}) -
D* - 83.5 mm {3-9/32 inches} (83.3 mm {3-9/32 inches})
E 63 mm (2-15/32 inches} 63 mm (2-15/32 inches}

* When mounting to a single-gang junction box, fix with two fixing screws (M4: locally procured) using the holes of either pattern C or D.

Stap 2: Fix the base bracket on the installation surface or on a junction box.
Pass the cables through the base bracket and then fix the base bracket on the installation surface or on a junction box (locally procured) with fixing screws (M4: locally procured).
When installing the base bracket on the installation surface
let wel:

  • When installing this product outdoors, be sure to apply waterproofing to the cable access hole and the holes for fixing the screw.

iPRO WVQJB500 W Adapter Box - FIG 5The illustration shown on the left is an example when installing on a wall using the combination of the fixing screw holes that is 83.5mm {3-9/32inches} × 46mm {1-13/16inches}.

■ When mounting the base bracket to a junction box
Select the holes on the base bracket so that they match with the screw holes of the junction box.
let wel:

  • When using a two-gang junction box, it is recommended that the boxes are arranged side by side as shown in the illustration below. (The cable connection work on the empty box side will become easier.)

iPRO WVQJB500 W Adapter Box - FIG 6

Step 3: Fix the attachment plate.
Fix the attachment plate with four fixing screws for the attachment plate (M4: accessory).
Recommended tightening torque: 1.37 N·m {1.01 lbf ft}

iPRO WVQJB500 W Adapter Box - FIG 7

let wel:

  • When wiring using a conduit, complete the connection work on the base bracket side before fixing the attachment plate.
  • When installing this product on a wall, fix the attachment plate with the “TOP⇧” mark facing upward.
  • When installing this product on a ceiling, fix the attachment plate so that the “TOP⇧” mark is faced in the direction where the camera is aiming at.

Stap 4: Install a camera or other bracket on this product.
■ When installing a camera
The following are descriptions of how to install WV-U1542L (outdoor box type) on a wall using this product as an example. The installation procedure is the same for other cameras.

  1. Hang the camera by hooking the installed auxiliary wire on this product on the hook on the rear of the camera mount base as shown in the illustration on the right.
  2. Connect the cables by following the instructions in the Installation Guide of the camera.
  3. Temporarily fix the camera mount base by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 8iPRO WVQJB500 W Adapter Box - FIG 9
  4. Fix the camera on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}
    iPRO WVQJB500 W Adapter Box - FIG 10

■ When mounting another bracket
The following are descriptions of how to install WV-QWL500-W (Wall Mount Bracket) on this product as an example.

  1. Pass the cable through WV-QWL500-W and temporarily fix it by hooking the screw for temporary fixing onto this product.iPRO WVQJB500 W Adapter Box - FIG 11
  2. Fix WV-QWL500-W on this product with four hexagon screws (M4: accessory) using a 3 mm hex wrench (locally procured).
    Recommended tightening torque: 1.37 N·m {1.01 lbf ft}iPRO WVQJB500 W Adapter Box - FIG 12
  3. Install the camera by following the Operating Instructions of WV-QWL500-W.
  • Lees hierdie instruksies aandagtig deur voordat u hierdie produk wil koppel of installeer en stoor hierdie handleiding vir toekomstige gebruik.
  • Die uiterlike voorkoms en ander dele wat in hierdie handleiding getoon word, kan verskil van die werklike produk wat nie die normale gebruik sal beïnvloed nie as gevolg van verbetering van die produk.

i-PRO Co., Ltd. aanvaar geen verantwoordelikheid vir beserings of skade aan eiendom wat voortspruit uit mislukkings wat voortspruit uit onbehoorlike installasie of werking wat nie met hierdie dokumentasie ooreenstem nie.

Let op: Kennisgewing:
• Before attempting to connect or operate this product, please read these instructions carefully. • This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily
reach it.
• For information about screws and brackets required for installation, refer to the corresponding section of this document.

Vir die VSA en Kanada:
i-PRO Americas Inc.
Vir Europa en ander lande:
i-PRO EMEA BV
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
iPRO WVQJB500 W Adapter Box - BAR CodeNs0520-1042
Gedruk in China

Dokumente / Hulpbronne

i-PRO WV-QJB500-W Adapter Box [pdf] Instruksiehandleiding
WV-QJB500-W, Adapter Box, WV-QJB500-W Adapter Box, Box

Verwysings

Los kommentaar

Jou e-posadres sal nie gepubliseer word nie. Verpligte velde gemerk *