OES-LOGO

HARVEST TEC 740DM Dye Sprayer Marking System

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-PRODUCT

Inleiding

Congratulations on purchasing a Harvest Tec Dye Sprayer Marking System. When attached to a 700 Series Automatic Applicator or 700 Series Moisture Only kit for any large square baler, will allow you to visibly mark the wet areas on your bales. The system includes the tank, pump, plumbing mounting hardware, and necessary cables. There is a parts breakdown in the back of the manual to reference if replacement parts are needed. All replacement parts and dye will be ordered through your local equipment dealer.

Bykomstighede benodig

  • Standaard sleutel stel
  • Hamer
  • Reguit kant
  • Standaard sok stel
  • Maatband
  • Metaal boor en sny gereedskap
  • Middelpunt
  • Marker

Installasie van kleurstofspuittenk en loodgieterswerk

Installasie van monteerbeugel en tenk – groot vierkante

Vind die tenk en monteerbeugel-samestelling. As u na Figure 1, 2 en 3 kyk, besluit watter van hierdie monteerplekke die gerieflikste sal wees en die beste vir die gebruiker sal werk.

  • Once tank location is decided, mark the mounting holes and drill out using a 3/8” bit.
  • Maak die monteerbeugel aan die baler vas met die 5/16” hardeware wat in die stel voorsien word.HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-1
  1. Figure 1: Common Hesston, Massey Ferguson, Challenger Balers
  2. Figure 2: New Holland 590,595, BB940-960A Case LBX331-432HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-2
  3. Figure 3: New Holland BB9060-9080 Case LB & New Holland BB Models

Stelselbedrading

  1. Locate the wiring harness (006-765IDM) supplied in the 740 dye Sprayer Marking Kit. Attached is 12 pin plug into the module mounted on the metal frame of the dye marker.
  2. Plug uncapped triangle plug into the plug on a metal frame.
  3. Run Dye Marking harness down to the main applicator harness (006-765B or 006-765B2) and attach it to one of the two CAN plugs.

Stelselbedradingsdiagram

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-3

Installation of Plumbing

Om die nat kolle in enige baal die beste te merk, beveel Harvest Tec aan dat die spuitpunte direk bo of onder die Star Wheels gemonteer word. Om die beste spuitpatroon direk op die nat plek van die baal gefokus te kry, sal die spuitpunte ongeveer 1” bokant die baal moet wees wat gemerk word. 'n Klein kerf moet dalk gesny word om die oppervlakte van die baal wat gemerk word te vergroot.

  1. Once you have the tank and mounting bracket securely fastened to the baler, locate parts A, B, C, D & E pictured below in Figure 1 or 2. Assemble in the following order:
  • Elmboog
  • nozzle holder
  • Kontroleerklep
  • reducing bushing
  • tip as pictured below.

let wel: All parts should be thread taped

  1. Once the nozzle holders are fastened to the balers, route the 3/8” hose to the tips. Make sure to fasten the hose securely but avoid pinching the lines. (Plumbing Diagram pictured in Figure 7)
    1. Keep from routing the hose in the way of moving parts on the baler.
  2. Attach drain hose top hose barb fitting at bottom of the tank. Run the hose to a secure point and attach valve assembly.HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-4

Installasie van loodgieterswerk en bedrading

  1. Install the tip and nozzle holder assemblies in the suggested locations pictured shown below. Use the 1/4” hardware provided to do so.HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-5
  • Maak seker dat die puntsamestellings (A) in lyn met die sterwiele (B) gemonteer is sodat die stelsel die nat kolle van die baal merk.

Loodgieter diagram

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-6

Algemene vraag

Is die merkkleurstof veilig vir veeverbruik?

  • Die DSM gebruik rooi-gekleurde, voedsel-graad kleurstof en is veilig vir alle vee.

Hoe laat ek die lug behoorlik uit die lyne uitblaas?

  • Remove the tips from the check valves that they’re threaded into and press the prime button on the dye marker until the air is pushed out of the lines.

Probleemoplossing

Probleem Moontlike oorsaak Oplossing
Die punte spuit nie Dye nie
  1.    The system is out of the dye.
  2. There is air in the lines, preventing a steady mist from coming from the tips.
  3. Damaged/pinched hose.
  4. The tip is plugged.
  5. Setpoint is set too high
  1.     Check the tank for a solution. If the tank is empty, refill and bleed air from lines.
  2.     Remove the tips from the check valves and using the priming button bleed the air out of the lines.
  3.     Inspect all the hoses making sure the lines are damaged or pinched.
  4.     Removed the tip from the bushing and inspect, clean is necessary.
  5.     Lower the set point level at which the user would like to have the bales marked at.

Onderhoud

  1. For winter storage, drain all of the liquid out of the lines and tank, and pump.

Vul tenk en eerste keer en jaarlikse opstart

Vul die tenk
Remove the tank lid from the 3-gallon tank. Make sure the tank is clean and completely empty. Mix the Dye (009-0800) with warm water inside the Dye bottle. Make sure that the the bottle is shaken vigorously so that the dye completely dissolves. Once the solution is mixed, add it to the 3-gallon tank and fill the tank with water.

Eerste keer en jaarlikse opstart

  • Once the tank has been filled the plumbing lines will need to be primed. With the system turned on and in a paused mode, hold the priming button until all the air is flushed out of the lines and there is a steady stream of liquid coming from each of the tips.

NOTA: The system needs to be primed every time the system has run out of dye.

  • You can adjust the moisture content level at which you would like the system to mark the ‘Wet Flakes’ in the bale is made. This can be done by entering ‘Setup’ followed by moisture setup, then adjusting Set Point.

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-7

Bedryfsinstruksies Outomatiese modus of Handmatige modus

Auto & Manual mode will automatically mark bales with dye if the moisture dye marking system is turned on and moisture content sensed by the star wheels is above the moisture ‘Set Point’ level that was set by the operator.

  1. The moisture sensed by the star wheels is indicated below. See page 9 for set-up instructions.

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-8

Speld uit

Integrated Dye Marker Module (IDM) on harness 006-765IDM (Deutsch Plug Number: DTM06-12SA)

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-9

  1. Pin Red+12V from ECU
  2. Pin Red/Black +12V, EOB
  3. Pin Black/White Ground, EOB
  4. Pin – –
  5. Pin – –
  6. Pin Purple Signal, EOB
  7. Pin Green ISO CAN Lo
  8. Pin Yellow ISO CAN Hi
  9. Pin Red/White +12 DSM
  10. Pin Black/White Ground DSM
  11. Pin Blue Prime, DSM
  12. Pin Black Ground from ECU

ISOBUS Plug on harness 006-765IDM (Deutsch Plug Number: DT04-4P)

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-10

  1. Pin Red +12V from ECU
  2. Pin Yellow ISO CAN Hi
  3. Pin Green ISO CAN Lo
  4. Pin Black Ground from ECU

End of Bale Sensor Plug on Harness 006-765IDM (Deutsch Plug Number: DT06-3S)HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-11

  1. Pin Red/Black +12V to End of Bale Sensors
  2. Pin Black/White Ground to End of Bale Sensors
  3. Pin Purple Signal

Prime Switch Plug on Harness 006-765IDM (Deutsch Plug Number: DT06-3S)

  1. Pin Orange/White+12V to Pump
  2. Pin Black/White Ground to Pump
  3. Pin Blue Prime

Onderdele-uiteensetting

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-12

HARVEST-TEC-740DM-Dye-Sprayer-Marking-System-FIG-13

Ref/ Description /Part /Qty

  1. Tank 005-9019 1
  2. DSM Mounting Bracket 001-2500 1
  3. Tank Cap 005-9022C 1
  4. Dye Marker Control 006-2472DM 1
  5. DSM Wire Harness 006-765IDM 1
  6. Remote Push Switch 006-2850 1
  7. DM Pump Switch 006-765IDM2 1
  8. Slang Clamp 002-9002 10
  9. 3/8” Barbed Tee 003-T3838 1
  10. 3/8” EPDM Hose 002-9003AS 26’
  11. DSM Pump 007-4120LF 1
  12. 3/4×1/4” Reducer 003-RB3414M 1
  13. 1/4×1/4” Nipple 003-M1414 1
  14. 1/4×3/8” Fitting 003-A1438 2
  15. 1/4″ FPT Tee 003-TT14 1
  16. 1/4×3/8” Elbow 003-EL1438 1
  17. SLV Bottle Valve 002-2216 1
  18. Male Quick Connect 004-4710 1
  19. Rubber Gasket 004-1207W 2
  20. Shut-Off Cap 004-1207F 1
  21. NP Tank Cap Gasket005-9022CG 1
  22. Nozzle Holder 001-4216 2
  23. Straight Fitting 003-A1438 2
  24. Vinnige verbinding 004-1207H 2
  25. Rubber Gasket 004-1207W 2
  26. Tip Screen 004-1203-100 2
  27. Check Valve 004-1207V 2
  28. Street Elbow 003-SE14F 2
  29. Nozzle Body 004-4722 2
  30. Brass Tip 004-TX-5 2
  31. Nozzle Cap 004-4723 2

Harvest Tec LLC. Waarborg en aanspreeklikheidsooreenkoms

Harvest Tec, LLC. sal komponente herstel of vervang wat foutief gevind word binne 12 maande vanaf die datum van vervaardiging. Onder geen omstandighede dek hierdie waarborg enige komponente wat na die mening van Harvest Tec, LLC. onderwerp is aan nalatige gebruik, misbruik, verandering, ongeluk, of indien herstelwerk gemaak is met onderdele anders as dié wat vervaardig en verkrygbaar is by Harvest Tec, LLC. Ons verpligting ingevolge hierdie waarborg is beperk tot die gratis herstel of vervanging van enige onderdeel wat volgens ons oordeel bewyse van gebrekkige of onbehoorlike vakmanskap aan die oorspronklike koper vervang, mits die onderdeel aan Harvest Tec, LLC terugbesorg word. binne 30 dae na die mislukking. As daar vasgestel word dat 'n nie-Harvest Tec-gemerkte hooi-preserveermiddel binne die Harvest Tec-toedienerstelsel gebruik is waar die mislukking plaasgevind het, behou Harvest Tec die reg voor om die waarborgversoek na goeddunke te weier. Onderdele moet deur die verkoopshandelaar en verspreider terugbesorg word, en vervoerkoste moet vooraf betaal word.

This warranty shall not be interpreted to render Harvest Tec, LLC. liable for injury or damages of any kind, direct, consequential, or contingent, to persons or property. Furthermore, this warranty does not extend to loss of crop, losses caused by delays, or any expense prospective profits or for any other reason. Harvest Tec, LLC. shall not be liable for any recovery greater in amount than the cost or repair of defects in workmanship. There are no warranties, either expressed or implied, of merchantability or fitness for a particular purpose intended or fitness for any other reason. This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, LLC. will not affect our ability to obtain materials or manufacture necessary replacement parts. Harvest Tec, LLC. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold.

HARVEST TEC, LLC.

  • POSBUS 63 2821 HARVEY STREET HUDSON, WI 54016
  • FOON: 715-386-9100
  • 1-800-635-7468.
  • FAKS: 715-381-1792
  • e-pos: info@harvesttec.com

Dokumente / Hulpbronne

HARVEST TEC 740DM Dye Sprayer Marking System [pdf] Eienaarshandleiding
740DM, Dye Sprayer Marking System, 740DM Dye Sprayer Marking System, Sprayer Marking System, Marking System, System

Los kommentaar

Jou e-posadres sal nie gepubliseer word nie. Verpligte velde gemerk *