FOS-logo

FOS technologies Razor Laser Multibeam RGB Laser Moving Head

FOS-technologies-Razor-Laser-Multibeam-RGB-Laser-Moving-Head-product

pak

Thank you for choosing our products. For your own safety, please read this manual before installing the device. This manual covers important information on installation and applications. Please install and operate the fixture with the following instructions, make sure the power is off before opening the light or repairing it. Meanwhile, please keep this manual well for future needs.

It is made of a new type of high-temperature strength of engineering plastics and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theaters, studios, nightclubs and discos. 6 modules RGB laser light which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation.

Veiligheidsmaatreëls

Versigtigheid!
Wees versigtig met u handelinge. Met 'n gevaarlike voltage, you can suffer a dangerous electric shock when touching wires

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this user manual.

Belangrik:
Skade wat veroorsaak word deur die verontagsaming van hierdie gebruikershandleiding is nie onderhewig aan 'n waarborg nie. Die handelaar sal nie aanspreeklikheid aanvaar vir enige gevolglike defekte of probleme nie.

If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore, it is essential that the device be earthed. The electric connection must carry out by a qualified person. The device shall only be used with rate voltage en frekwensie. Maak seker dat die beskikbare voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer.

Ontkoppel altyd van die stroomnet wanneer die toestel nie gebruik word nie of voordat dit skoongemaak word. Hanteer net die kragkabel aan die prop. Moet nooit die prop uittrek deur die kragkoord te trek nie.

During the initial start-up, some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective, it should decrease gradually. Please don’t project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

Belangrikste kenmerke

  • Voltage: AC100-240V,50/60HZ
  • Laser color: RGB full color
  • Laser krag: 3W
  • RGB 500mw*6PCS (R:100mw G:200mw B:200mw) Laser pattern: a variety of rough beam effect patterns.
  • Y-Axis rotating: 240°
  • Rotation angle: 270°
  • Control mode: Music / Automatic / DMX512 (11/26/38CH) Scanning system: stepping motor
  • Scanning angle of motor: 25 degrees
  • Rated power:<180W
  • Working environment: indoor Lamp
  • Produkgrootte: 85 x 16 x 45 cm
  • Size of carton case (1in1): 92 x 16 x 32 cm
  • N.W: 11kgs / G.W:12.6kgs
  • Size of carton case (2in1): 94.5 x 34 x 33.5 cm
  • N.W: 23kgs / G.W:26.5kgs

Operasie instruksies

  • The moving head is for laser purposes.
  • Don’t turn on the fixture if it’s been through severe temperature difference like after transportation because it might damage the light due to the environmental changes. So, make sure to operate the fixture until it is in normal temperature.
  • Hierdie lig moet weggehou word van sterk skud tydens enige vervoer of beweging.
  • Moenie die lig net met die kop optrek nie, want dit kan skade aan die meganiese dele veroorsaak.
  • Moenie die toebehore blootstel in oorverhitting, vog of omgewing met te veel stof wanneer dit geïnstalleer word nie. En moenie enige kragkabels op die vloer lê nie. Of dit kan elektroniese skok vir die mense veroorsaak.
  • Maak seker dat die installasieplek in 'n goeie veiligheidstoestand is voordat die toebehore geïnstalleer word.
  • Maak seker dat jy die veiligheidsketting sit en kyk of die skroewe behoorlik geskroef is wanneer die toebehore geïnstalleer word.
  • Make sure the lens is in good condition. It’s recommended to replace the units if there are any damages or severe scratches.
  • Maak seker dat die toebehore deur gekwalifiseerde personeel bedien word wat die toebehore ken voordat dit gebruik word.
  • Hou die oorspronklike pakkette as enige tweede versending nodig is.
  • Moenie probeer om die toebehore te verander sonder enige instruksie deur die vervaardiger of die aangestelde herstelagentskappe nie.
  • Dit is nie binne die waarborgreeks as daar enige wanfunksies is as gevolg van die nie volg van die gebruikershandleiding om te gebruik of enige onwettige handeling, soos skokkortsluiting, elektroniese skok,amp gebreek, ens.

Display menu control

Press MENU to choose Address / DMX/ Color/ Manual/ Demo /Auto/Sound/ Temp /Version /Hours, then press ENTER to confirm or to enter the next step.if there are more function for options, press UP/DOWN to choose, then press ENTER to confirm, then press MENU to exit, or wait for 10 and exit automatically.

Opmerkings:
If no operation on any button, the display will turn off automatically in 20 seconds; if no DMX signal, the first dot of the display will turn on statically, if with DMX signal, the dot will flash

  • DMX Address A001
  • A512 Address Code
  • Channel Mode 11CH, 26CH, 38
  • CH channel selection
  • Show Mode SOUND AUTO, effect selection
  • Slave Mode MASTER, SLAVE, main and auxiliary machine selection
  • Black Out YES, NO Standby mode
  • Sound State ON, OFF voice switch
  • Sound Sense sound sensitivity (0 off, 100 most sensitive)
  • Pan Inverse
  • YES, NO level reverse
  • Tilt1 Inverse YES, NO vertical reverse
  • Tilt2 Inverse YES, NO vertical reverse
  • Tilt3 Inverse YES, NO vertical reverse
  • Tilt4 Inverse YES, NO vertical reverse
  • Tilt5 Inverse YES, NO vertical reverse
  • Tilt6 Inverse YES, NO vertical reverse
  • Back Light ON, OFF backlight switch
  • Auto Test Auto Test
  • Firmware Version V104 software version number
  • Defaults YES, NO Restore factory settings
  • System Reset YES, NO Machine reset

DMX Channels 11Channel Mode

CH funksie DMX-waarde besonderhede
1 Pan motor 0-255 0-360°positioning
2 Pan motor

spoed

0-255 Van vinnig tot stadig
3 Tilt1—Tilt6

motor stroke

0-255 0 no function 1-255

0°-360° positioning

4 Kantel motor

spoed

0-255 Van vinnig tot stadig
 

 

 

 

 

 

5

 

 

 

 

 

 

Selfaangedrewe

0-55 Geen funksie nie
56-80 Self-propelled effect 1 (XY

uncontrollable)

81-105

106-130

131-155

156-180

Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
181-205 Sound control (XY

uncontrollable)

206-230 Self-propelled effect 6 (XY

uncontrollable)

231-255 Sound control (XY

uncontrollable)

6 Selfaangedrewe

spoed

0-255 self-propelled speed and

Sound-activated sensitivity

7 Dimmer 0-255 0-100% total dimming
 

8

 

strobe

0-9 Geen strobe nie
10-255 Strobespoed van stadig na vinnig
 

 

 

9

 

 

 

Laser-effek

0-15 Geen funksie nie
16-27 Effek 1
 

......

Every time the DMX value is increased by 12, there will be

an effect

232-243 Effek 19
244-255 Effek 20
10 Laser-effek 0-255 self-propelled speed from fast
  spoed   te stadig
 

11

 

Herstel

0-249 Geen funksie nie
250-255 machine reset (value stays for

5 sekondes)

26Channel Mode

CH funksie DMX-waarde besonderhede
1 Pan motor 0-255 0-360°positioning
2 Pan motor

spoed

0-255 Van vinnig tot stadig
3 Tilt1 motor 0-255 0°-360° positioning
4 Tilt2 motor 0-255 0°-360° positioning
5 Tilt3 motor 0-255 0°-360° positioning
6 Tilt4 motor 0-255 0°-360° positioning
7 Tilt5 motor 0-255 0°-360° positioning
8 Tilt6 motor 0-255 0°-360° positioning
9 Tilt1-Tilt6

motor

0-255 0 no function     1-255 0°-360°

posisionering

10 Kantel motor

spoed

0-255 speed from fast to slow
 

 

 

 

 

 

11

 

 

 

 

 

 

Selfaangedrewe

0-55 Geen funksie nie
56-80 Self-propelled effect 1 (XY

uncontrollable)

81-105

106-130

131-155

156-180

Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
181-205 Sound control (XY

uncontrollable)

206-230 Self-propelled effect 6 (XY

uncontrollable)

231-255 Sound control (XY

uncontrollable)

12 Selfaangedrewe

spoed

0-255 self-propelled speed and

Sound-activated sensitivity

13 Dimmer 0-255 0-100% total dimming
14 strobe 0-9 Geen strobe nie
10-255 Strobespoed van stadig na vinnig
15 Red laser 1-6

verduistering

0-255 0 geen funksie nie

1-255 1-100% dimming

16 Groen laser

1-6 dimming

0-255 0 geen funksie nie

1-255 1-100% dimming

17 Blue laser 1-6

verduistering

0-255 0 no function       1-255 1-100%

verduistering

 

 

 

 

18

 

 

 

The first group of RGB lasers

0-31 Off
32-63 rooi
64-95 groen
96-127 Blou
128-159 geel
160-191 Purple
192-223 Cyan
224-255 Vol helder
 

 

 

 

19

 

 

 

The second group of RGB lasers

0-31 Off
31-63 rooi
64-95 groen
96-127 Blou
128-159 geel
160-191 Purple
192-223 Cyan
224-255 Vol helder
 

 

 

 

20

 

 

 

The third group of RGB lasers

0-31 Off
32-63 rooi
64-95 groen
96-127 Blou
128-159 geel
160-191 Purple
192-223 Cyan
224-255 Vol helder
 

 

 

 

21

 

 

 

The fourth group of RGB lasers

0-31 Off
32-63 rooi
64-95 groen
96-127 Blou
128-159 geel
160-191 Purple
192-223 Cyan
224-255 Vol helder
 

 

 

 

22

 

 

 

The fifth group of RGB lasers

0-31 Off
32-63 rooi
64-95 groen
96-127 Blou
128-159 geel
160-191 Purple
192-223 Cyan
224-255 Vol helder
23 Die sesde 0-31 Off
  group of RGB lasers 32-63 rooi
64-95 groen
96-127 Blou
128-159 geel
160-191 Purple
192-223 Cyan
224-255 Vol helder
 

 

 

 

24

 

 

 

Laser-effek

0-15 Geen funksie nie
16-27 Effek 1
 

......

Every time the DMX value is

increased by 12, there will be an effect

232-243 Effek 19
244-255 Effek 20
25 Laser-effek

spoed

0-255 self-propelled speed from fast to

stadig

 

26

 

Herstel

0-249 Geen funksie nie
250-255 machine reset (value stays for 5 seconds)

38Channel Mode

CH funksie DMX-waarde besonderhede
1 Pan motor 0-255 0-360°positioning
2 Pan motor

spoed

0-255 Van vinnig tot stadig
3 Tilt1 motor 0-255 0-360°positioning
4 Tilt2 motor 0-255 0-360°positioning
5 Tilt3 motor 0-255 0-360°positioning
6 Tilt4 motor 0-255 0-360°positioning
7 Tilt5 motor 0-255 0-360°positioning
8 Tilt6 motor 0-255 0-360°positioning
9 Tilt1—Tilt6

motor stroke

0-255 0 geen funksie nie

1-255 0°-360° positioning

10 Tilt motor speed 0-255 speed from fast to slow
 

 

 

 

11

 

 

 

 

Selfaangedrewe

0-55 Geen funksie nie
56-80 Self-propelled effect 1 (XY

uncontrollable)

81-105

106-130

131-155

156-180

Self-propelled effect 2 (XY uncontrollable)…Self-propelled effect 5 (XY uncontrollable)
181-205 Sound control (XY uncontrollable)
206-230 Self-propelled effect 6 (XY
      uncontrollable)
231-255 Sound control (XY uncontrollable)
12 Selfaangedrewe

spoed

0-255 self-propelled speed and

Sound-activated sensitivity

13 Dimmer 0-255 0-100% total dimming
14 strobe 0-9 Geen strobe nie
10-255 Strobespoed van stadig na vinnig
15 Red laser 1-6

verduistering

0-255 0 geen funksie nie

1-255    1-100% dimming

16 Green laser 1-6

verduistering

0-255 0 geen funksie nie

1-255 1-100% dimming

17 Blue laser 1-6

verduistering

0-255 0 geen funksie nie

1-255 1-100% dimming

18 The first group

of red lasers

0-255 0-100% verduistering
19 The first group

of green lasers

0-255 0-100% verduistering
20 The first group

of blue lasers

0-255 0-100% verduistering
 

21

Die tweede

group of red lasers

0-255  

0-100% verduistering

...... ...... ...... ......
33 Die sesde groep

of red lasers

0-255 0-100% verduistering
34 Die sesde groep

of green lasers

0-255 0-100% verduistering
35 Die sesde groep

of blue lasers

0-255 0-100% verduistering
 

 

 

36

 

 

 

Laser-effek

0-15 Geen funksie nie
16-27 Effek 1
...... Every time the DMX value is increased

by 12, there will be an effect

232-243 Effek 19
244-255 Effek 20
37 Laser-effek

spoed

0-255 self-propelled speed from fast to slow
 

38

 

Herstel

0-249 Geen funksie nie
250-255 machine reset (value stays for 5 seconds)

Onderhoud en skoonmaak

Die volgende punte moet tydens die inspeksie oorweeg word:

  1. All screws for installing the devices or parts of the device must be tightly connected and must not be corroded.
  2. There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling, suspension, trussing).
  3. Meganies-beweegde dele moet geen spore van slytasie toon nie en moet nie met onbalanse roteer nie.
  4. Die elektriese kragtoevoerkabels mag geen skade, materiaalmoegheid of sedimente toon nie.

Further instructions depending on the installation spot and usage must be adhered by a skilled installer and any safety problems have to be removed.

Versigtigheid!
Ontkoppel van die hoofstroombron voordat instandhouding begin.

In order to make the lights in good condition and extend the lifetime, we suggest a regular cleaning to the lights.

  1. Clean the inside and outside lens each week to avoid the weakness of the lights due to the accumulation of dust.
  2. Maak die waaier elke week skoon.
  3. A detailed electric check by an approved electrical engineer every three months makes sure that the circuit contacts are in good condition, and prevents the poor contact of the circuit from overheating.

We recommend frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents. There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.

Dokumente / Hulpbronne

FOS technologies Razor Laser Multibeam RGB Laser Moving Head [pdf] Gebruikershandleiding
Razor Laser, Multibeam RGB Laser Moving Head, RGB Laser Moving Head, Moving Head, Razor Laser

Los kommentaar

Jou e-posadres sal nie gepubliseer word nie. Verpligte velde gemerk *