KuWFi 2.4GHz Outdoor Wireless CPE Bridge User Manual

1. Introduction

The KuWFi Outdoor Wi-Fi Bridge is a 300Mbps outdoor CPE Wi-Fi Bridge designed for extending wireless network coverage over long distances. It complies with IEEE 802.11b/g/n standards and features a built-in panel antenna, enabling Point-to-Point (PTP) or Point-to-Multipoint (PTMP) transmission distances of up to 1000 meters under optimal conditions.

Constructed with an ABS waterproof, dustproof, and sunscreen shell, this device is temperature adaptive and supports 24V passive PoE and 4KV lightning protection, making it suitable for various harsh outdoor environments.

2. Key Features

• 300Mbps 2.4G Wi-Fi Bridge: Offers a maximum Wi-Fi rate of 300Mbps. Equipped with 10/100Mbps network ports (LAN1/LAN2), providing a faster and more stable network. LAN2 port supports 24V POE.
• AP / Repeater Mode: Supports universal Access Point (AP) and Repeater modes, allowing for flexible deployment and extended Wi-Fi signal range up to 1KM when used in pairs.
• Built-in Panel Antenna: Optimized for outdoor Wi-Fi camera monitoring with PTP/PTMP ranges of 500m to 1KM.
• One-click Fast Pairing: Simplifies the setup process for point-to-point connections by allowing automatic pairing with a single button press.
• 100Mbps Ethernet Ports: The CPE bridge features LAN1 and LAN2 ports, both supporting 10/100Mbps. LAN2 also supports 24V POE, enabling more flexible installation of equipment in designated locations.
• Dual Power Supply Modes: Supports 24V PoE power supply and DC 12V power supply (DC 12V adapter not included).
• Outdoor Durability: Features professional lightning protection, IP65 waterproof, and dustproof ABS plastic shell, suitable for multiple harsh environments.

3. Setup and Installation

3.1. One-touch Automatic Pairing (PTP/PTMP)

The CPE Bridge devices are primarily used for long-range signal bridging and repeating. To avoid IP address conflicts with other router devices, DHCP is disabled by default. Follow these steps for one-touch automatic pairing:

1. Power Connection: Connect the CPE with power using the POE adapter. Connect one end of the Ethernet cable to the POE port on the POE power supply, and the other end to the CPE's LAN port.
2. Set Working Mode:
   • For the Master AP, move the toggle switch to the 'A' position.
   • For the Slave AP, move the toggle switch to the 'C' position.
3. Initiate Pairing: Simultaneously press the RST buttons on both the Master AP and Slave AP for one second.
4. Wait for Pairing: The devices will automatically pair.

3.2. Initial PC Connection for Configuration

It is recommended to use a wired connection for initial setup.

Method 1 - Wired Connection:

1. Connect one end of a network cable to the LAN port of the Master AP.
2. Connect the other end of the network cable to your PC's network port.

Method 2 - Wireless Connection:

On your PC, search for the CPE's Wi-Fi SSID: "Wireless XXXX" (where XXXX is the last four digits of the device's unique identification number).

3.3. Configure PC IP Address

To access the CPE's web interface, you need to set a static IP address for your PC. Use 192.168.1.xxx (where xxx is between 2 and 80, e.g., 192.168.1.10).

1. Find the network icon in the lower right corner of your PC's screen and click "Open Network and Internet Settings".
2. Select "Ethernet" and click "Change Adapter Options".
3. Right-click the network connection in use and select "Properties".
4. Double-click "Internet Protocol Version 4 (TCP/IPv4)".
5. Select "Use the following IP address:" and enter:
   • IP address: 192.168.1.10
   • Subnet mask: 255.255.255.0
6. Click "OK" to confirm.

4. CPE Bridge Configuration (WEB UI)

Before configuring the Bridge IP, AP Configuration, or Client Configuration, ensure your PC and CPE are properly connected and the PC IP is configured as described above.

It is recommended to use Google Chrome for configuration.

1. Open Google Chrome and enter the IP address:
   • Master AP: 192.168.1.88
   • Slave AP: 192.168.1.89
2. The login interface will appear. The default login password is: admin.

4.1. Check Bridge Status and Operating Mode

After logging in, you can view the bridge status and operating mode on the home page (Dashboard).

Master AP (192.168.1.88) Example:

4.2. CPE Wireless Settings (Master AP)

In the Wireless settings, you can modify the SSID name, password, and encryption methods for the wireless bridge.

Example Settings:

4.3. CPE Wireless Advanced Settings

Under Advanced settings, you can configure additional wireless features such as region, wireless transmission power, channel, and bandwidth.

Example Settings:

4.4. CPE Network Settings

The CPE supports both dynamic and static IP addresses. No additional configuration is typically required under normal circumstances.

Example Settings:

4.5. CPE Support Cloud Settings

The Cloud AC platform allows for centralized management of devices, including gateways, billing, and cloud APs. You can view device status and modify configurations in the cloud.

Example Settings:

5. Operating Modes and Applications

The CPE Bridge system is versatile and finds extensive application in various monitoring and network extension scenarios.

5.1. Operating Modes

The CPE Bridge supports two primary working modes:

• Access Point (AP) Mode: One unit acts as an AP, broadcasting the Wi-Fi signal.
• Client Mode (Repeater Mode): The other unit acts as a client, receiving the Wi-Fi signal and extending it.

A single AP can pair with multiple client units, significantly expanding signal coverage and network capacity. The working mode can be effortlessly switched between AP Mode and Repeater Mode with one click.

5.2. Typical Applications

The CPE Bridge is ideal for:

• Residential surveillance
• Highway monitoring
• Reservoir and river monitoring
• Lift security
• Construction crane oversight
• Port and terminal operations
• Marine aquaculture monitoring
• Extending network to a second building
• Extended camera monitoring range
• Point to Multipoint connections (without obstacles)

6. Maintenance

6.1. CPE System Settings

The system settings page allows you to manage the CPE's firmware, configuration, and device reboot:

• Firmware Upgrade: Upgrade the CPE's firmware version.
• Upload/Backup Configuration: Backup the current configuration files or upload previous configurations.
• Restore to Factory Default: Reset the device to its original factory settings.
• Reboot Device: Restart the CPE device.

6.2. CPE Ping Watchdog Settings

The Ping Watchdog feature monitors network connectivity by sending ping packets to a target IP/domain. If no response is received, it can trigger alerts or preset actions (e.g., device restart) to resolve connectivity issues and ensure real-time network availability.

Configurable parameters include:

• Target Address
• Checking Interval
• Number of Failures before action
• Ping Timeout
• Action (Reboot, Close Wireless, Restart Network, Enable Rescue SSID, No Action)

6.3. CPE Scheduled Reboot Settings

Configuring scheduled reboots helps clear cached files and ensures optimal device operation. It is strongly recommended to set up scheduled reboots.

Configurable parameters include:

• Reboot Cycle (e.g., Every Day)
• Reboot Time

6.4. Physical Maintenance

The device features a robust outdoor ABS plastic shell with professional lightning protection, IP65 waterproof, and dustproof ratings. Regular visual inspection for physical damage and ensuring proper sealing of ports can help maintain its durability in harsh environments.

7. Troubleshooting and FAQ

7.1. Common Issues and Solutions

• Q: How to pair Bridges?
  A: Set one Bridge as Master ('A' switch) and the other as Slave ('C' switch). Simultaneously press the 'RST' button on both Bridges for one second. They will automatically pair.
• Q: Cannot access the WEB UI page for IP Address configuration.
  A: Ensure your computer is connected to the bridge and has a static IP address set (e.g., 192.168.1.10 with subnet mask 255.255.255.0). Then, open a browser and input 192.168.1.88 (for AP) or 192.168.1.89 (for Repeater). Remember to restore your PC's original network settings after configuration.
• Q: Outdoor Wi-Fi bridge range is less than described.
  A: Transmission distance is affected by environmental factors like buildings, trees, and local network conditions. Avoid walls or other obstacles during installation.
• Q: Weak Wi-Fi signal or short transmission distance.
  A: Adjusting the Wi-Fi protocol and bandwidth in the WEB UI can affect network speed and transmission distance. Continuous debugging for your specific environment and requirements is recommended.
• Q: Does the bridge support 360-degree signal transmission?
  A: No, the bridge uses panel antennas and does not support 360-degree transmission. For optimal stability, install the two Bridges face-to-face.
• Q: Cannot find a Wi-Fi signal.
  A: Different countries support different Wi-Fi channels. Log into the WEB UI page to change the country region for Wi-Fi signal or try another channel.
• Q: Outdoor Wi-Fi bridge is not powered.
  A: Ensure the product's WAN or POE port is correctly connected to the adapter's POE port. If the issue persists, try changing the adapter and RJ45 LAN cable.

8. Technical Specifications

8.1. Package Listing:

• 2x 2.4GHz CPE Bridge
• 2x POE Power Supply
• 2x Network Cable
• 1x Manual

9. User Tips

• For best performance, ensure the two CPE Bridges are installed facing each other directly, minimizing physical obstructions like walls or dense foliage.
• If experiencing signal issues, experiment with different Wi-Fi channels and bandwidth settings in the WEB UI to find the optimal configuration for your environment.
• Always restore your PC's original network settings after configuring the CPE Bridge to ensure normal internet access.
• Regularly check for firmware updates via the System Settings in the WEB UI to ensure your device has the latest features and security patches.

10. Support and Contact Information

Thank you for choosing the KuWFi network device. If you encounter any problems during use, please contact us for support.

Customer Service Email: support@kuwfi.com

Manufacturer: Shenzhen HuaXuFeng Technology Development Co., LTD

Address: Room 1102, Youcheng Building, Minzhi Street, Longhua District, Shenzhen 518111

TEL: 86-0755-28010121

Mobile/WhatsApp: +8618002530681

Designed by Kuwfi in Shenzhen, Mainland China.

10.1. Safety Precautions

• Do not use incorrect or unauthorized chargers.
• Do not use metallic objects to contact short circuit electrodes.
• Do not get the device wet.
• Do not expose the device to excessive heat, humidity, or corrosive environments.
• It is recommended to install and use the device under the guidance of professionals or with adequate professional knowledge.