1. Introduction
The SINO A10 Plus is a state-of-the-art IMU GPS GNSS RTK measurement equipment designed for high-precision surveying applications. Featuring 1590 channels, extended battery life, and a super integrated radio, this device offers reliable and accurate data collection for land surveying, topographic surveys, and cadastral surveys. Its robust design and advanced features ensure efficient performance in complex environments.
2. Package Contents
Upon unpacking your SINO A10 Plus system, please verify that all the following components are present and in good condition:
- Receiver (2 units)
- Controller (1 unit)
- Controller bracket (1 unit)
- Charger (2 units)
- Data cable (2 units)
- UHF antenna (2 units)
- 30cm extension rod (1 unit)
- Adapter (2 units)
3. Product Overview & Features
The SINO A10 Plus is engineered for precision and durability, offering a range of features to enhance surveying efficiency:
- Advanced GNSS Tracking: Supports 7 Stars and 30 frequencies with up to 1590 parallel channels for full constellation tracking, ensuring performance in complex environments.
- Super IMU: Integrated Inertial Measurement Unit allows for up to 60° tilt measurement with 2.5 cm accuracy, improving efficiency by 30%.
- High Accuracy: Achieves 52cm accurate measurement through a new inertial navigation algorithm and anti-magnetic interference technology.
- Rapid Initialization: Features ultra-easy 5-second initialization by simply shaking the device back and forth.
- NFC Easy Connection: Advanced NFC technology enables automatic connection with a single touch.
- Extended Battery Life: Unique low-power design provides up to 30 hours of operation on a single full charge.
- Compact & Lightweight: The receiver is designed to be compact and light, weighing approximately 750g and being as thin as 8.5cm.
- Enhanced UHF Radio: Offers an impressive working range of up to 15KM with 2W power consumption.
- Durable Construction: Built with a magnesium alloy AZ91D body, ensuring robustness and longevity.
- IP68 Rating: Dust and waterproof for reliable operation in challenging field conditions.
- External Power Support: Compatible with USB port external power supply for continuous operation.
4. Setup Instructions
Follow these steps to set up your SINO A10 Plus RTK measurement equipment:
- Charge the Batteries: Before initial use, fully charge the receiver and controller batteries using the provided chargers and data cables.
- Assemble the Receiver: Attach the UHF antenna to the receiver. If using a pole, secure the receiver to the 30cm extension rod.
- Mount the Controller: Attach the controller to the controller bracket, then secure the bracket to the pole or a suitable mounting point.
- Power On: Press and hold the power button on both the receiver and the controller until they power on.
- Connect Devices: Utilize the NFC Easy Connection feature by touching the NFC-enabled areas of the receiver and controller to establish a connection. Alternatively, connect via Bluetooth or Wi-Fi as per the controller's interface instructions.
- Initialization: For accurate measurements, especially with the IMU function, perform the 5-second initialization by gently shaking the receiver back and forth until the system indicates readiness.
- Software Configuration: Launch the surveying software on the controller. Configure project settings, coordinate systems, and base/rover modes as required for your specific application.
5. Operating Instructions
The SINO A10 Plus controller software provides a user-friendly interface for various surveying tasks:
- Accessing Functions: The interface features a simple and reasonable layout. Built-in help documents and real-time video calls are available to assist users.
- Point Measurement: Navigate to the 'Point Measurement' function. Position the receiver over the desired point and follow the on-screen prompts to record the coordinates.
- Point Stakeout: Use the 'Point Stakeout' function to guide you to specific coordinates. The controller will provide real-time directions to reach the target point.
- Road Stakeout: The system supports direct import of data in multiple road formats. Utilize this feature to automatically edit and stake out road designs.
- CAD Drawing Construction: For complex projects, the controller can automatically search for drawings, import CAD files with one click, and offer multi-preview functions to simplify CAD drawing construction.
- Personalized Settings: Customize interface styles, voice broadcasting, and point measurement styles to suit your preferences.
6. Maintenance
Proper maintenance ensures the longevity and optimal performance of your SINO A10 Plus equipment:
- Cleaning: Regularly clean the receiver and controller with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
- Storage: Store the equipment in its protective carrying case in a cool, dry place when not in use. Avoid extreme temperatures and direct sunlight.
- Battery Care: Fully charge batteries before long-term storage and recharge every 3-6 months to prevent deep discharge. Use only the provided chargers.
- Firmware Updates: Periodically check for and install any available firmware updates for both the receiver and controller to ensure optimal performance and access to new features.
- Physical Inspection: Before each use, inspect all cables, connectors, and antennas for any signs of wear or damage.
7. Troubleshooting
This section addresses common issues you might encounter with your SINO A10 Plus:
- No Power:
- Ensure batteries are fully charged.
- Check all power connections and cables.
- If using external power, verify the power source is functioning correctly.
- No GNSS Signal/Poor Accuracy:
- Ensure the receiver has a clear view of the sky, free from obstructions.
- Verify that the UHF antenna is securely connected.
- Perform the 5-second initialization procedure by shaking the receiver.
- Check the controller software for satellite visibility and signal strength.
- Ensure correct base station setup and data link if operating in RTK mode.
- Connection Issues (NFC/Bluetooth/Wi-Fi):
- Ensure both devices are powered on.
- For NFC, ensure the NFC areas are touching correctly.
- For Bluetooth/Wi-Fi, ensure they are enabled on both devices and try re-pairing/reconnecting.
- Restart both the receiver and controller.
- Software Malfunctions:
- Restart the controller and the surveying application.
- Ensure the software is up-to-date.
- If issues persist, consult the built-in help documents or contact support.
8. Specifications
| Category | Specification |
|---|---|
| Model Number | Sino A10Plus |
| Brand Name | Sino / XMSJ |
| DIY Supplies | Metalworking |
| Origin | Mainland China |
| Application | Land Surveying, topographic survey, cadastral survey |
| Channels | 1590 / 1598 |
| Inertial Measurement | Yes (IMU: Up to 60° tilt with 2.5 cm accuracy) |
| Material | Magnesium alloy AZ91D body |
| Battery Life | Up to 30 hours |
| External Power Supply | Support USB port external power supply |
| Standard Internal Rx | 410 - 470 MHz |
| Enhanced UHF Range | Up to 15KM |
| Dust & Waterproof | IP68 |
| Power Consumption | 1.4W |
| Input Voltage | 6-28 VDC |
GNSS Performance
| System | Frequency Point/Signal |
|---|---|
| GPS | L1C/A, L2P, L1C, L2C, L5 |
| GLONASS | G1C, G1P, G2C, G2P, G3 |
| Galileo | E1, E5b, E5a, E5AltBoc, E6c |
| BDS-2 | B1, B2, B3 |
| BDS-3 | B1C, B2a, B2b, B2b-ppp |
| SBAS | L1C/A, L5C |
| QZSS | L1C/A, L2C, L5, L1s, L5s, L6 |
| IRNSS | L5 |
GNSS Accuracies
| Mode | Horizontal | Vertical |
|---|---|---|
| Static and Fast Static | 2.5 mm + 0.5 ppm | 5 mm + 0.5 ppm |
| Long Observations Static | 3 mm + 0.1 ppm | 3.5 mm + 0.4 ppm |
| Real Time Kinematic (RTK) | 8mm + 1ppm | 15 mm + 1 ppm |
| DGPS | <0.4 m RMS | |
| SBAS | 1 m 3D RMS | |
| Standalone | 1.5 m 3D RMS | |
| PPP | 10cm | 20cm |
Communication & Electrical
| Category | Details |
|---|---|
| Serial Port | Supports serial communication |
| USB | Type-C interface |
| Data Protocols | LTE-FDD, LTE-TDD, DC-HSDPA HSPA+, HSDPA, HSUPA, WCDMA, TD-SCDMA, CDMA, EDGE, GPRS |
| Antenna | Three in one antenna |
| Data Formats | NMEA-0183: GPGGA, GPGPSV, GPGSA, GPRMC, GPVTG, GPZDA Sinan binary format: cnb (sinognss custom) RTCM2.x: RTCM1B, RTCM3B, RTCM9B, RTCM1819B, RTCM59B RTCM3.0: 1004, 1005, 1006, 1007, 1008, 1011, 1104, 1033 RTCM3.2: MSM4, MSM5 |
| WIFI | 802.11b/g/n |
9. User Tips
Leverage these tips to maximize your experience with the SINO A10 Plus:
- Quick Initialization: Always perform the quick 5-second shake initialization for the IMU to ensure the highest accuracy, especially when starting a new measurement session or after significant movement.
- NFC Convenience: Utilize the NFC feature for fast and hassle-free connections between the receiver and controller, saving time in the field.
- Software Exploration: Take advantage of the built-in help documents and real-time video calls within the controller software to quickly learn and master advanced functions like road stakeout and CAD drawing construction.
- Battery Management: For prolonged field work, consider carrying a portable USB power bank to utilize the external power supply feature and extend operational time beyond the internal 30-hour battery life.
- Regular Updates: Keep your device's firmware and software updated to benefit from performance improvements and new features.
10. Warranty & Support
The SINO A10 Plus comes with a 1-year warranty from the date of purchase, covering manufacturing defects and malfunctions under normal use. For warranty claims or technical assistance, please contact our support team.
Contact Information:
- WhatsApp: +86 15373439653
- Telegram: +86 15373439653
- Email: hongdou@surdoca.com
11. Frequently Asked Questions (FAQ)
- Q: What does the SINO A10 Plus package include?
- A: The package typically includes two receivers, one controller, one controller bracket, two chargers, two data cables, two UHF antennas, one 30cm extension rod, and two adapters. Please refer to the 'Package Contents' section for a complete list.
- Q: Can I use a custom logo on the products?
- A: Yes, custom logos can be printed on the products and their packaging boxes.
