ADVANTECH SEG520-4SFP-T Industrial Managed Ethernet Switch
Product Information
| Model # | Description | Temp Rating |
|---|---|---|
| SEG5204SFP-T | 16 Port GbE + 4 GbE SFP Full L2 Industrial Managed Ethernet Switch | N/A |
Product Usage Instructions
Before you begin, be sure you have the following:
- Ethernet Switch
- Din Rail Mount Bracket (Installed)
- Wall Mount Bracket
- Power Supply (Required not included)
Hardware Installation
Wall Mounting
Follow the steps below to wall mount the Ethernet switch:
- Choose a suitable location on the wall.
- Use appropriate screws and wall anchors to securely attach the wall mount bracket to the wall.
- Slide the Ethernet switch onto the wall mount bracket and ensure it is securely attached.
DIN Rail Mounting
Follow the steps below to DIN rail mount the Ethernet
switch:
- Choose a suitable location on the DIN rail.
- Slide the DIN rail mount bracket onto the DIN rail and ensure it is securely attached.
- Slide the Ethernet switch onto the DIN rail mount bracket and ensure it is securely attached.
Terminal Blocks
The Ethernet switch has terminal blocks for power input. Follow the instructions below to connect the power:
- Connect Power Input 1 (12 to 48VDC) to the respective terminal block.
- Connect Power Input 2 (12 to 48VDC) to the respective terminal block.
- Ensure proper grounding by connecting the DC Ground wires to the respective terminal block.
LED Status
The Ethernet switch has several LEDs that indicate its status.
Refer to the table below for LED status descriptions:
| LED | Status | Description |
|---|---|---|
| LED SYS | Green | System is operating normally |
| LED R.M. | Green Off | No Power / system crash / operation initiating |
| LED PWR1 | Green Off Solid Red | Powered up Power down or not installed |
| LED PWR2 | Blinking Red Off | Powered up Power down or not installed |
| Alarm | Green Off Defined Major policies are detected Defined minor policies are detected Powered off or system operating normally |
Default Settings
The Ethernet switch has the following default settings:
- IP Address: 192.168.1.1
- Subnet mask: 255.255.255.0
- Default gateway: 192.168.1.254
- Username: admin
- Password: admin
Product Overview
Hardware Installation
DIN Rail Mounting
Wall Mounting
Terminal Blocks
| Terminal | Description |
| V2- | Power Input 2 (DC Ground) |
| V2+ | Power Input 2 (12 to 48VDC) |
| P-Fail | Power Fault Relay |
| P-Fail | Power Fault Relay |
| V1- | Power Input 1 (DC Ground) |
| V1+ | Power Input 1 (12 to 48VDC) |
- Wire Gauge: 12-24 AWG (3.31 – 0.205 mm2).
- Torque: 7lb-in.
LED Status
| LED | Status | Description |
| SYS | Green | System is operating normally |
| Off | No Power / system crash / operation initiating | |
| R.M. | Green | Active when determining ring master |
| PWR1 | Green | Powered up |
| Off | Power down or not installed | |
| PWR2 | Green | Powered up |
| Off | Power down or not installed | |
| Alarm | Solid Red | Defined Major policies are detected |
| Blinking Red | Defined minor policies are detected | |
| Off | Powered off or system operating normally |
Default Settings
- IP Address: 192.168.1.1
- Subnet mask: 255.255.255.0
- Default gateway: 192.168.1.254
- Username: admin
- Password: admin
Recommended Accessories
MDR-40-24
Power Supply
C5UMB3FBG
Ethernet Cables
Troubleshooting
If no LEDs light, verify that the power supply connections are solid and that power is present on the output of the power supply.
Use the LED table to verify that power is present, a link is established, data is being transmitted, and to verify port speed.
If data does not pass and cable connections have been verified, contact your Network Administrator to validate that the network connection is good.
If you encounter any issues with the Ethernet switch, follow the troubleshooting steps below:
- Ensure that the power supply connections are secure and that power is present on the output of the power supply.
- Refer to the LED table to check if power is present, a link is established, and data is being transmitted.
- If data does not pass and cable connections have been verified, contact your Network Administrator to validate the network connection.
You can find the complete user manual in the documentation and download section of the product web page. Follow the steps below to access it:
- Go to www.advantech-bb.com.
- Search for the model number.
- Visit the documentation/download section of the product page to download the files.
If you need further assistance, please contact our support team:
Phone: 1-888-948-2248 (US) | Europe: +353 91 792444
Email: support@advantech-bb.com
Website: www.advantech-bb.com
Address: 707 Dayton Road, PO Box 1040, Ottawa, IL 61350
Phone: 815-433-5100 | Fax: 815-433-5109
Documents / Resources
 | ADVANTECH SEG520-4SFP-T Industrial Managed Ethernet Switch [pdf] User Guide SEG520-4SFP-T Industrial Managed Ethernet Switch, SEG520-4SFP-T, Industrial Managed Ethernet Switch, Managed Ethernet Switch, Ethernet Switch |
