ADLER AD 7731 Ceramic Fan Heat Tower
LCD with Remote control User Manual

ADLER AD 7731 Ceramic Fan Heat Tower LCD with Remote control User Manual

ADLER AD 7731 Ceramic Fan Heat Tower LCD with Remote control - Model identifier

This product is suitable only for occasional use or for use in well insulated room.

ADLER AD 7731 Ceramic Fan Heat Tower LCD with Remote control - Overview 1ADLER AD 7731 Ceramic Fan Heat Tower LCD with Remote control - Overview 2

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

The warranty conditions are different, if the device is used for commercial purpose.”

  1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
  2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
  3. The applicable voltage is 220-240V, ~50/60Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
  4. Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
  5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
  6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
  7. Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc. Never use the product in humid conditions.
  8. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
  9. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
  10. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
  11. Never use the product close to combustibles.
  12. Do not let cord hang over edge of counter or touch hot surfaces.
  13. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
  14. In order to provide additional protection, it is recommended to install residual current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
  15. Never use this device close to water, e.g.: under shower, in bath tube, or above sink filled with water.
  16. If using the device in bathroom after use remove the power plug from the socket, because water proximity presents risk, even if the device is turned off.
  17. Do not put your fingers or any objects through the ventilation grille
  18. Do not place any objects on the convector. The vents must not be covered by a towel, curtain, etc. may cause a malfunction or fire.
  19. Keep the distance between the convector and other items such as furniture, curtains.
  20. Convector is equipped with a device to prevent overheating. Automatically turns off the convector in the event of excessive temperature convector (due to clogged vents, fan malfunction ) . In this case, disconnect the unit from the power supply , waiting a few minutes and remove the cause of overheating,
  21. Do not touch the hot parts of the convector . Do not touch the appliance with wet hands.
  22. In the case of wet convector or falling of any object through the ventilation grille of the convector , turn it off immediately and disconnect from the network. Before re-use with convector call for service.
  23. Do not place the convector directly below the electrical outlet.
  24. Always turn off the convector button before disconnecting it from the mains.
  25. Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
  26. Do not use this heater if it has been dropped
  27. Do not use if there are visible signs of damage to the heater
  28. Use the heater on a level and stable surface or attach it to the wall, if provided for by the manufacturer

WARNING: Do not use this heater in small rooms where there are people who are unable to leave them by themselves, unless constant supervision is ensured.

WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at least 1 m away from the heater air outlet.

ADLER AD 7731 Ceramic Fan Heat Tower LCD with Remote control - Caution Hot Surface“Caution Hot Surface” – The temperature of accessible surfaces may be higher when the equipment is in operation, which means that the housing elements become hot during operation during operation, BE CAREFUL !!!

ADLER AD 7731 Ceramic Fan Heat Tower LCD with Remote control - avoid overheating iconWARNING: In order to avoid overheating – do not cover the heater. The device is not to be covered with clothing, blankets and other textile products which could cause ignition.

BEFORE FIRST USE

In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. This device should only be placed on a firm level surface and a minimum 50cm distance from walls or any other objects. It is a way to optimize air flow, avoid placing the device in corners and small spaces.

Product description: Tower fan heater

1. LCD panel
2. Buttons
3. Air outlet grid
4. Indication light
5. Handle
6. Air inlet grid
7. Power switch
8. Base
9. Remote control
10. Power button
11. Temperature decrease button
12. Oscillation button
13. Heat setting button
14. Timer button
15. Temperature increase button
16. Fan indicator
17. Heat indicator: level I – 1200W
18. Heat indicator: level II – 2200W
19. Timer indicator
20. Oscillation indicator
21. Desired temperature level

USAGE 

  1. Ensure the power switch (7) is off. Insert the plug into a suitable power outlet and turn the power supply on by power (7) located at the back of the device. The device is in standby mode.
  2. When in standby mode, only power button (10) on control panel will respond your touch. Turn on the device by pressing the power button (10) on either the remote or control panel. The device will blow cold air by fan function illustrated by fan indicator (16).
  3. Press the Heat setting button (13) once to operate low heating mode 1200W, or twice to operate high heating mode 2200W. You can see one sun (17) or two suns (17+18) at control panel. After 10 minutes all displayed symbols will be turn off automatically.
  4. To turn off the device press the power button (10). Please note: the unit will take approximately 30 seconds to stop blowing out air. Turn off the power switch (7) at the back of the unit.

TIMER FUNCTION: 

The timer function can be used in any mode. The timer allows you to set the length of time from 1-8 hours. To use the timer, press the timer button (14). Each press of the button increases the time set by 1 hour, at the same moment the timer indicator (19) will be displayed. The amount of time set will be displayed on the unit, and will count down in 1 hour. If the timer has been set for 8 hours (MAX amount of time) pressing the button once more will reset the Timer Function.

OSCILLATION FUNCTION:

Press the oscillation button (12) to turn on the oscillation function. The device starts to swing left and right side. At the same time the oscillation indicator (20) will be displayed. Press the oscillation button (12) again to turn off the oscillation function.

TEMPERATURE SETTING:

By pressing buttons (15) and (11) set up desired room temperature.

  1. The temperature range is available in the range from 10 to 49 degrees. Press button (15) to increase the desired temperature and press button (11) to decrease the desired room temperature. The desired room temperature is shown by symbol (21).
  2. The device working on full power when the room temperature is 4°C lower than the setting temperature. The device working on half power when the room temperature is between 0° and 2°C lower than the setting temperature. The device switches off when the room temperature is higher than the setting temperature. The fan working 30 seconds to make inside cool to protect components, then fan stops, the device enter into standby. The device switches on again when the room temperature falls 2°C below the setting temperature.

WARNING: During use, do not touch or cover the air inlet and air outlet.

WARNING: Allow the device to cool down for 30-60 seconds before switching on again and before turning off at the power outlet. This will protect the inner parts.

Remote control (9) operation is same as manual operation of buttons on control panel. To use the device with the remote control (9) supplied, pull the installing film. In order to remove the battery, simply squeeze the small tab and pull. Insert 1 x CR2025 (3V) lithium battery into the small crevice as illustrated.

IMPORTANT: The + symbol on the battery inserted should be facing upwards. Firmly close the battery compartment to begin using the Remote Control (9).

SAFERTY PROTECTION

1. OVERHEAT PROTECTION: This device is fitted with a safety overheat protection device. If overheating occurs, ensure the power switch is off and turn off the power supply. Unplug the device and let it cool down for 30 minutes. If something is obstructing grids, ensure the object is removed. Check with unit appearance, power cord and plug if no damaged before switch on again. Next, after 30 minutes has passed, turn the device on.

2. TIP-OVER SWITCH: The device will only work on a firm stable surface. If the device is not 100% stable, vertical position, the unit will switch off until placed in the correct position.

CLEANING AND MAINTENANCE

1. Make sure the device is not hot.
2. Before cleaning the device remove the plug from the electrical socket.
3. Keep the air inlet and outlet openings clean. Do not allow dust to collect on the openings.
4. Clean the housing using only dry or moist cloth.
5. Do not immerse the device in water!

TECHNICAL DATA

Voltage: 220-240V ~50Hz
Power: 2200W
Battery: 1 x CR2025 (3V) lithium battery included

Disposal Icon

To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.

ADLER Products

Documents / Resources

ADLER AD 7731 Ceramic Fan Heat Tower LCD with Remote control [pdf] User Manual
AD 7731, Ceramic Fan Heat Tower LCD with Remote control, AD 7731 Ceramic Fan Heat Tower LCD with Remote control

References

Leave a comment

Your email address will not be published. Required fields are marked *