Mpow S10 Sports Wireless Earphones User Manual BH303A

USER MANUAL

Sports Wireless Earphones

Sports Wireless Earphones
Mpow S10 / BH303A

We are appreciated for purchasing our Mpow S10. This guide contains instructions for setting up and using you Mpow S1 O easily.

Package

Package

Diagram

Diagram

How To Pair

How To Pair

First use

First use

  1. Turn on the Bluetooth function on your phone.
  2. Power it on, then it will enter the pairing mode automatically. Orange and white lights will start flashing alternately with the voice “Pairing”
  3. Search for the Bluetooth devices and select “M pow S10 “(Enter the code “0000” if needed).
  4. When pairing is successful, the white light will start flashing slowly. You will also hear the voice “Connected”.

Pair to another device

  1. In the state of shut-down, keep pressing the MFB button for 5-7 seconds or so. Do not release it until the orange and white lights start flashing alternately with the voice “Pairing”.
  2. The rest goes the same as above.

Power ON / OFF

Power ON / OFF

Redial/ Play/ Pause/ Answer/ Hang Up/ Reject/ Siri

Redial/ Play/ Pause/ Answer/ Hang Up/
Reject/ Siri

Volume Control/ Music Control

Volume Control/ Music Control

Charge Battery

Charge Battery

Correct Disposal of This Product

( Waste Electrical& Electronic Equipment )

Disposal

This Marking shown on the product or its literature indicate that it should not be disposed with other household wastes at the end of its working life.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it response to promote the sustainable reuse of material resources Household user should contact either the retailer where they purchased this product or their local government office. for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contact This product should not be mixed with other commercial wastes for disposal.

FCC Statement

Operation is subject to the following three conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

(3) This device has been evaluated to meet general RF exposure requirement The device can be used in portable exposure condition without restriction.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and. if not installed and used in accordance with the instruction, may cause harmful Interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receil.er is connected.
  • Consult the dealer or an experienced radio /W technician for help.

Notification

  1. Please fully charge it if it was going to lay idle for a long time and place
    it in a cool and dry place. Please recharge it each 2 months for storage.
  2. Please fully charge it for the first use.

Questions about your Manual? Post in the comments!

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. My wife and I each have a pair of the Mpow S10 headphones and we listen to different music.

    Is there a way to ensure that her phone connects to her buds and my phone connects to my buds. We struggled the other day with connecting to each others buds.

    Doug

    Doug McGill asks My wife and I each have a pair of the Mpow S10 headphones and we listen to different music.

    Is there a way to ensure that her phone connects to her buds and my phone connects to my buds. We struggled the other day with connecting to each others buds.

    Doug

    Manuals+ clarified question
    Question

    How can I prevent two pairs of Mpow S10 earphones from cross-connecting to the wrong phones when used in the same area?

    Answer

    To ensure each pair of Mpow S10 earphones connects only to the intended phone, you should manage the initial pairing process and the order in which you power them on. Because both devices share the same Bluetooth name (Mpow S10), your phones may struggle to distinguish between them if both are in pairing mode at the same time.

    Follow these steps to stabilize your connections:

    • Clear Previous Pairings: On your phone, go to Bluetooth settings and "Forget" or "Unpair" any existing Mpow S10 entries. Do the same on your wife's phone.
    • Pair One at a Time: Turn off Bluetooth on your wife's phone. Put your earphones into pairing mode (press and hold the MFB button for 5-7 seconds until the orange and white lights flash) and connect them to your phone. Once connected, turn your earphones off.
    • Repeat for the Second Pair: Turn off Bluetooth on your phone. Have your wife put her earphones into pairing mode and connect them to her phone.
    • Sequential Power On: In the future, try to turn on one pair of earphones and let it connect to its respective phone before turning on the second pair. This prevents the second phone from accidentally "grabbing" the signal of the first pair while they are searching for a connection.

    If the phones continue to cross-connect, you can manually select the correct device from your phone's Bluetooth menu, or ensure that the person who is not currently using their headphones has their Bluetooth toggled off temporarily.

    1. Reset both pairs of buds, and remove them from the bluetooth settings in both phones.

      After reset, be sure you only pair each set with one phone.

      admin asks Reset both pairs of buds, and remove them from the bluetooth settings in both phones.

      After reset, be sure you only pair each set with one phone.

      Manuals+ clarified question
      Question

      How can I prevent two pairs of Mpow S10 earphones from cross-connecting to the wrong phones when used in the same area?

      Answer

      Reset both pairs of buds, and remove them from the bluetooth settings in both phones.

      After reset, be sure you only pair each set with one phone.

  2. The phone no longer finds the headphones despite being turned on, how do they reset?
    Thanks

    Il telefono non trova più le cuffie nonostante siano accese, come si resettano?
    Grazie

    Edoardo asks <em>The phone no longer finds the headphones despite being turned on, how do they reset?
    Thanks</em>
    Il telefono non trova più le cuffie nonostante siano accese, come si resettano?
    Grazie
    Manuals+ clarified question
    Question

    How do I reset the Mpow S10 BH303A earphones if my phone cannot find them?

    Answer

    While the Mpow S10 manual does not specify a dedicated "reset" button combination, you can force the earphones back into pairing mode to allow your phone to find them again. Follow these steps:

    1. Turn off the earphones: Ensure the device is powered down.
    2. Enter Pairing Mode: From the shut-down state, press and hold the MFB (Multi-Function Button) for approximately 5-7 seconds.
    3. Wait for the lights: Do not release the button until you see the orange and white lights flashing alternately and hear the voice prompt say "Pairing".
    4. Reconnect: Open the Bluetooth settings on your phone, search for devices, and select "Mpow S10".

    If the device still does not appear, try "forgetting" or deleting any previous Mpow S10 entries in your phone's Bluetooth list and restarting your phone's Bluetooth function.

  3. Overnight I have one side that stopped working. Is there a way to fix this or my headphones are broken?
    Du jour au lendemain j’ai un côté qui a cessé de fonctionner. Est ce qu’il y a moyen de réparer ça ou mes écouteurs sont fichus ?

    Anonymous asks <em>Overnight I have one side that stopped working. Is there a way to fix this or my headphones are broken?
    Du jour au lendemain j'ai un côté qui a cessé de fonctionner. Est ce qu'il y a moyen de réparer ça ou mes écouteurs sont fichus ?
    Manuals+ clarified question
    Question

    One side of my Mpow S10 earphones stopped working. How can I fix this?

    Answer

    If one side of your Mpow S10 earphones has stopped working, you can try the following troubleshooting steps to determine if it is a software glitch or a hardware failure:

    • Reset the Connection: Forget the "Mpow S10" from your phone's Bluetooth settings, turn off Bluetooth, and then re-pair the device following the manual's instructions (hold the MFB button for 5-7 seconds until lights flash orange and white).
    • Check for Debris: Ensure there is no earwax or debris blocking the speaker mesh of the silent earbud, as this can significantly muffle or block sound.
    • Test with Another Device: Pair the earphones with a different phone or computer. If the issue persists across all devices, the internal wiring or driver in that earbud is likely damaged.
    • Check for Physical Damage: Since these are sports earphones, sweat or moisture ingress can sometimes cause temporary or permanent failure. Ensure the charging port cover was sealed and the unit is dry.

    If these steps do not restore sound, the headphones are likely broken internally. As the manual does not provide a specific factory reset button combination beyond the pairing mode, hardware failure is the most probable cause for a single-sided outage.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.